Hdd Format - Yamaha CDR-HD1000 Service Manual

CDR-HD1000
QQ
3 7 63 1515 0
knob.
(1) "Main FW (CD)" means upgrading the system control firmware from CD-ROM.
(2) "CDRW FW (CD)" means upgrading the CD-R/W drive firmware from CD-ROM.
(3) "All FW (CD)" equal executing "Main FW (CD)" and "CDRW FW (CD)" at the same time.
(4) "Main FW (HDD)" means upgrading the system control firmware from internal HDD backup.
(5) "CDRW FW (HDD)" means upgrading the CD-R/W drive firmware from internal HDD backup.
4. Select "Main FW (CD)" and press the "MULTI JOG" knob.
5. "Push PLAY KEY" is displayed. Press the "
6. "Downloading" is displayed. NEVER TURN OFF THE POWER WHILE "Downloading" IS DISPLAYED.
7. When finishing the recovery, "Complete" is displayed and the CDR-HD1000 is rebooted.
8. Confirm that the firmware version has been changed from old to new.
3.2.2 The CD-R/W drive firmware recovery
If the CD-R/W drive doesn't work after updating its firmware, the CD-R/W drive firmware may be corrupted.
In this case, you can recover the CD-R/W drive firmware by the following procedures.
1. Turn off the power.
Turn on the power while pressing the "
Keep pressing until the start up sequence is finished.
2. Press the "MENU" key to enter MENU mode.
3. Rotate the "MULTI JOG" knob to select "Sys. Utility".
Press the "MULTI JOG" knob. "Firm. Version" is displayed.
4. Rotate the "MULTI JOG" knob to select "Firm. Update".
Press the "MULTI JOG" knob.
5. "Main FW (HDD)" is displayed. Two types of upgrade mode can be selected by rotating the "MULTI JOG"
knob.
(1) "Main FW (HDD)" means upgrading the system control firmware from internal HDD backup.
(2) "CDRW FW (HDD)" means upgrading the CD-R/W drive firmware from internal HDD backup.
6. Select "CDRW FW (HDD)". Press the "MULTI JOG" knob.
TE
L 13942296513
7. "Push PLAY KEY" is displayed. Press the "
8. "Downloading" is displayed. NEVER TURN OFF THE POWER WHILE "Downloading" IS DISPLAYED.
9. When finishing the recovery, "Complete" is displayed and the CDR-HD1000 is rebooted.
10. Confirm that the firmware version has been changed from old to new.
CAUTION: Never press the "CDR" and "COPY" keys during the above sequence.

HDD FORMAT

Use the following procedure for initialization of the hard disk drive.
1. Turn on the power.
2. Press the "HDD" key to select HDD and then press the "MENU" key.
3. Turn the "MULTI JOG" knob to select "HDD Utility" and then press the "MULTI JOG" knob.
4. Turn the "MULTI JOG" knob to select "HDD Format" and then press the "MULTI JOG" knob. Then "Initialize
?" is displayed.
5. Press the " " key, and "Format Really" is displayed.
6. Press the "INPUT" key.
7. Wait for "No data" to be displayed.
8. Turn off the power.
www
.
13
http://www.xiaoyu163.com
" key to start update.
" key and the "MENU" key.
" key to start update.
x ao u163
y
i
http://www.xiaoyu163.com
2 9
8
Q Q
3 6 7 1 3 1 5
co
.
9 4 2 8
0 5 8 2 9 9 4 2 8
m
9 9
9 9