End Call; Outgoing Calls; Redial; Incoming Calls - AEG AR 4021 BT Instruction Manual

Confirm your selection with the
‹
ton (5). DIAL
Enter with the help of the
‹
tons the desired phone number.
Save the phone number by pressing the
‹
SEL button. SAVE OK is shown on the
display.
NOTE
►
If you have entered one or more numbers
incorrectly, you can delete the numbers
using the
Press briefly: The numbers are deleted
individually.
Keep pressed: All entered numbers are
deleted.
►
The saved speed dials are lost if the car
radio has been reset using the RESET but-
ton (30).
Use a saved speed dial number
Press the button (3). DIAL
‹
on the display.
Now keep the corresponding numeric
‹
button pressed to call the desired phone
number. CALLING appears on the display.
RECEIVED Here you can display a list of the last received
phone numbers. Press the
the displayed number.
DIALED
Here you can display the last 10 dialed phone
numbers.
MISSED
Here you can display missed calls.
MANU
Call answering settings
ANS / ■ MANU ANS
: To accept a call you must
AUTO press the button (3).
■
ANS AUTO ANS : The car radio accepts the call
without having to press the button.
TALK You can set the desired talk volume here.
VOLUME

End call

/BND button (26) to end outgoing or
Use the
‹
incoming calls. CALL END is shown on the display.
NOTE
►
To reject an incoming call, press again the
button (26).

Outgoing calls

Press the button (3). DIAL
‹
display.
The phone number is entered using the numeric
‹
buttons. The entered phone number is shown on the
display of the car radio.
SEL but-
is shown on the display.
numeric but-
/BND button (26).
is shown
button (3) to call
/BND
is shown on the
NOTE
►
If you have entered one or more numbers incor-
rectly, you can delete the numbers using the
BND button (26).
Press briefly: The numbers are deleted individually.
Keep pressed: All entered numbers are deleted.
To call the desired number, press afterwards the
‹
button (3). CALLING is shown on the display.

Redial

The unit saves the last dialed number. To retrieve this, fol-
low the steps below:
Press the button twice (3). LAST NUM and then the
‹
last selected phone number is shown on the display.
Press the button (3) again to call the phone num-
‹
ber.

Incoming calls

When there are incoming calls, a ring tone sounds from
the speakers and if the caller has a CLIP "Calling Line
Identification Presentation (Caller ID)" enabled phone, the
caller number appears on the car radio display. Otherwise
"RINGING" appears on the display.
To be able to answer an incoming call, press the
‹
button (3). You can listen to the caller through via the
speakers in your car.

Transfer call between car radio and mobile phone

You can transfer a call again to your mobile phone.
To do so, keep the T-MENU button (25) pressed.
‹
TRANSFER is shown on the display (7). The car radio
activates the MUTE mode. Keep this button down
again pressed to transfer the call to the car radio.
Music reproduction via A2DP (Advanced
Audio Distribution Profile)
This involves a cross-manufacturer Bluetooth profile.
Stereo audio signals are transferred wireless between the
playback unit (source) and receiver unit. To be able to
remote control the source, the playback unit must support
the AVRCP profile (Audio Video Remote Control Profile).
Full functionality cannot be guaranteed due to different
unit manufacturers, model and software versions.
After you have connected the devices to each other,
‹
you can start to music reproduction using the PAU
button (9). You must start music reproduction before-
hand on your mobile phone, depending on the device
manufacturer, model and software versions.
Use the / buttons (23) to select the next or previous
‹
music title.
ENGLISH
91
/