Advertisement
Available languages
Available languages
english
life, do not discharge batteries fully. It is
recommended that the batteries be recharged after
each use.
leaving the battery in the charger
The charger and battery pack can be left connected with
the green LED glowing indefinitely. The charger will keep
the battery pack fresh and fully charged.
imPortant charging notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature is
between 65°F and 75°F (18°- 24°C). DO NOT charge
the battery pack in an air temperature below +40°F
(+4.5°C), or above +105°F (+40.5°C). This is important
and will prevent serious damage to the battery pack.
2. The charger and battery pack may become warm to
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed, or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check current at receptacle by plugging in a lamp
or other appliance
b. Check to see if receptacle is connected to a light switch
which turns power off when you turn out the lights.
c. Move charger and battery pack to a location
where the surrounding air
approximately 65°F - 75°F (18°- 24°C).
d. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily done
previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may also
charge a partially used pack whenever you desire with no
adverse affect on the battery pack.
5. Foreign materials of a conductive nature such as,
but not limited to, steel wool, aluminum foil, or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the
cavity. Unplug charger before attempting to clean.
6. Do not freeze or immerse charger in water or any
other liquid.
Warning: shock hazard. Do not allow any liquid
to get inside charger. Never attempt to open the battery
pack for any reason. If the plastic housing of the battery
pack breaks or cracks, return to a service center for
recycling.
safety Warnings and
instructions: drills
1. Hold drill firmly with one hand on the grip and the
other hand on the bottom of the battery pack.
2. When attaching accessories in the drill chuck, hand
tighten the keyless chuck firmly.
8
(original instructions)
temperature is
Warning: Drill may stall (if overloaded or improperly
used) causing a twist. Always expect the stall. Grip the
drill firmly with both hands to control the twisting action
and prevent loss of control which could cause personal
injury. If a stall does occur, release the trigger immediately
and determine the reason for the stall before re-starting.
installing and removing the
battery Pack from the tool
Warning: Make certain the lock-off button is
engaged to prevent switch actuation before removing or
installing battery.
TO INSTALL BATTERY PACk: Insert battery (5) into
tool until an audible click is heard (figure b). Ensure
battery pack is fully seated and fully latched into
position.
TO REMOVE BATTERY PACk: Depress the battery
release button (6) as shown in figure c and pull battery
pack out of tool.
oPerating instructions
trigger sWitch & reversing button
(figure d)
• The drill is turned ON and OFF by pulling and releasing
the trigger switch (1). The farther the trigger is
depressed, the higher the speed of the drill.
• A forward/reverse control button (2) determines the
direction of the tool and also serves as a lock off
button.
• To select forward rotation, release the trigger switch and
depress the forward/reverse control button to the left.
• To select reverse, depress the forward/reverse
control button the opposite direction.
note: The center position of the control button locks
the tool in the off position. When changing the position
of the control button, be sure the trigger is released.
drill / drive mode select (figure e)
This drill is equiped with mode select buttons (3) to
quickly and easily change the performance of the tool
to drilling or driving based upon your project.
• To set the tool to drive mode, press the botton
marked with the
symbol.
• To set the tool to drill mode, press the botton
marked with the
symbol.
note: A blue LED will light the symbol for the mode
that is selected.
state of charge indicator (figure e)
The drill is equipped with a state of charge indicator. This
can be used to display the current level of charge in the
battery during use. It does not indicate tool functionality
and is subject to variation based on product components,
temperature, and end-user application.
checking state of charge during use:
• Insert the battery (5) into the tool as shown in
figure b.
Advertisement
