CHAPTER 1 GENERAL ADJUSTMENTS SAFETY INSTRUCTIONS WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” INSTRUCTIONS BELOW. X-RAY RADIATION PRECAUTION 1. Excessive high voltage can produce potentially hazardous 2. This receiver is equipped with a Fail Safe (FS) circuit which X-RAY RADIATION.
WARNING: BEFORE SERVICING THIS CHASSIS, READ THE “X-RAY RADIATION PRECAUTION”, “SAFETY PRECAU- TION” AND “PRODUCT SAFETY NOTICE” ON PAGE 3 OF SERVICE MANUAL. SET-UP ADJUSTMENT I The following adjustments should be made when a complete realignment is required or a new picture tube is installed. Perform the adjustments in order as follows : 1.
Page 5
(5) Adjust the sub-4-pole magnets only in case there is any deviation of Xv bow-shaped convergence. (To be usually set at the initial position) Align both sides with the sub-4-pole magnets and minimize the deviation of blue and red with the main 4-pole magnets. Xv bow-shaped deviation of convergence red/blue blue...
SERVICE MODE 1. ENTERING TO SERVICE MODE 1) Press MUTE button once 2) Press MUTE button 3) While pressing the MUTE button, on Remote Control. again to keep pressing. press MENU button on TV set. MUTE (Service mode display) 2. DISPLAYING THE ADJUSTMENT MENU 1) Press MENU button on TV.
Page 7
4. SELECTING THE ADJUSTING ITEMS 1) Every pressing of CHANNEL s button in the service mode changes the adjustment items in the order of table-2. (t button for reverse order) Refer to table-2 for preset data of adjustment mode. (See SETTING & ADJUSTING DATA on page 13) 5.
Page 8
8. SELF DIAGNOSTIC FUNCTION 1) Press “9” button on Remote Control during display of adjustment menu in the service mode. The diagnosis will begin to check if interface among IC’s are executed properly. 2) During diagnosis, the following displays are shown. SELF CHECK NO.
DESIGN MODE 1. ENTERING TO DESIGN MODE 1) Select the Service mode. 2) While pressing RECALL button on 3) Press MENU button on TV. Remote and press MENU button on TV. Item Press Data Press (Design mode) (Adjustment mode) When QA02 is initialized, items “OPT0” and “OPT1” and "OPT2" of DESIGN MODE are set to the data of the representative model of this chassis family.
ELECTRICAL ADJUSTMENT ITEM ADJUSTMENT PROCEDURE FOCUS VR ADJ 1. Enter the service mode, then select any register item. 2. Press the TV/VIDEO button on the Remote until the black cross-bar pattern ap- pears on the screen. 3. Adjust the FOCUS control (on T461) for well defined scanning lines on the picture screen.
Page 11
ITEM ADJUSTMENT PROCEDURE HORIZONTAL POSITION 1. Call up the adjustment mode display, then select the item HPOS or VPOS. (HPOS) 2. Press the TV/VIDEO button on Remote until the VERTICAL POSITION white cross-bar or black cross-bar pattern appears (VPOS) on the screen. 3.
CIRCUIT CHECKS HIGH VOLTAGE CHECK Troubleshooting Guide for Fail Safe Circuit CAUTION: There is no HIGH VOLTAGE ADJUSTMENT on this chassis. Checking should be done following the steps Check that the set returns to normal operation when pin 12 below. of Z801(or emitter of Q472) is grounded with jumper wire.
CHAPTER 2 SPECIFIC INFORMATIONS SETTING & ADJUSTING DATA SAFETY INSTRUCTIONS 32" HIGH VOLTAGE AT ZERO BEAM: 32.7kV MAX HIGH VOLTAGE: 34.1kV Table-1 SERVICE MODE ADJUSTING ITEMS AND DATAS IN THE SERVICE MODE: Item Name of adjustment Preset Item Name of adjustment Preset Data Data...
LOCATION OF CONTROLS (Representative: 32AF43) Front View OUTSIDE IND. & CONTROLS: FRONT DEMO MENU TV/VIDEO VOLUME CHANNEL VIDEO-3 IN S-VIDEO VIDEO L/MONO AUDIO INSIDE DOOR RMT SENSOR POWER VOLUME Remote VIDEO-3 IN DEMO MENU CHANNEL TV/VIDEO T / S sensor...
Remote Control MUTE POWER RECALL MUTE RECALL POWER Channel Number CH RTN CH RTN MENU CHANNEL s/t MENU/ ENTER Menu s/t VOLUME T/S Menu T/S TV/CABLE/VCR CABLE EXIT Set to "TV" to control the TV. EXIT FAV CH t/s button FAV CH TV/VIDEO TV/VIDEO...
PROGRAMMING CHANNEL MEMORY The channel memory is the list of TV channel numbers your TV will stop on when you press the CHANNEL s or t button. First, use the TV/CABLE and CH PROGRAM functions to preset all active channels in your area automatically. If necessary, arrange the preset channels with the ADD/ERASE functions so that you can tune into only desired channels.
• The part number must be used when ordering parts, in order to assist in processing, be sure to include the Model number and Description. • The PC board assembly with mark is no longer available after the end of the production. Model :32AF43, 32AF53 Capacitors ..... CD Ceramic Disk : Plastic Film : Electrolytic Resistors ....
Page 18
Location Location Parts No. Description Parts No. Description C466 24503041 PLASTIC FILM , 63V 0.1UF J C834 24503047 PLASTIC FILM, 63V 0.33UF J * C467 24095879 PLASTIC FILM, 630V 0.022UF H C840 24795221 ELECTROLYTIC, 25V 220UF M * C469 24095879 PLASTIC FILM, 630V 0.022UF H C842 24792101...
Page 20
ELECTROLYTIC, 10V 470UF M CZ530 24092730 CERAMIC CHIP, 16V B 0.1UF K (32AF53) CZ03 24092442 CERAMIC CHIP, 16V F 0.47UF Z (32AF43) CZ540 24092730 CERAMIC CHIP, 16V B 0.1UF K (32AF53) CZ05 24109103 CERAMIC CHIP, 50V B 0.01UF K (32AF43)
SCHEMATIC DIAGRAM MODEL : 32AF43 / 32AF53 WARNING: BEFORE SERVICING THIS CHASSIS, READ THE "X-RAY RADIATION PRECAUTION", "SAFETY PRECAUTION" AND "PRODUCT SAFETY NOTICE" ON THE MANUAL FOR THIS MODEL. CAUTION: The international hazard symbols "*" in the schematic diagram and the parts list designate components which have special characteristics important for safety and should be replaced only with types identical to those in the original circuit or specified in the parts list.
SPECIFICATIONS (Representative : 32AF43) TELEVISION SYSTEM NTSC standard CHANNEL COVERAGE VHF: 2 through 13 UHF: 14 through 69 Cable TV: mid band (A-8 through A-1, A through I) super band (J through W) hyper band (AA through ZZ, AAA, BBB)