Connections - Sony CDX-GT315C Service Manual

CDX-GT315C
QQ
3 7 63 1515 0
• E model
Location of controls and basic operations
Main unit
1 2 3 4 5
OFF
PUSH SELECT
EQ3 SOURCE
SEEK SEEK
BTM MODE
DIM ALBM
DSPL 1 2
9 q; qa qs qd qfqg qh
Card remote commander
RM-X151
wa
1
OFF ATT
ws
4
SOURCE SEL MODE
qd
ql
+
wd
–
qk
qf
DSPL SCRL
1 2 3
wf
4 5 6
+
w;
VOL
–
TE
6
L 13942296513

• CONNECTIONS

• US, Canadian model
A
*
AUDIO OUT REAR
* AUDIO OUT SUB/REAR
B
BUS AUDIO IN
BUS CONTROL IN
www
BUS AUDIO IN
Source selector*
Sélecteur de source*
XA-C40
.
BUS CONTROL IN
6
http://www.xiaoyu163.com
6 7 8
AUX
REP SHUF PAUSE
3 4 5 6 SCRL
CDX-GT315C
qj qk
Refer to the pages listed for details. The
corresponding buttons on the card remote
commander control the same functions as those
on the unit.
A OFF button
To power off; stop the source.
B EQ3 (equalizer) button 9
To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
GRAVITY, CUSTOM or OFF).
C Volume control dial/select button 9
To adjust volume (rotate); select setup items
(press and rotate).
D SOURCE button
To power on; change the source (Radio/CD/
MD* 1 /AUX).
E Disc slot
Insert the disc (label side up), playback
starts.
F Display window
G AUX input jack 10
To connect a portable audio device.
H Z (eject) button
To eject the disc.
I BTM button 8
To start the BTM function (press and hold).
J
(front panel release) button 5
x ao
y
i
* not supplied
non fourni
http://www.xiaoyu163.com
8
K SEEK –/+ buttons
CD:
To skip tracks (press); skip tracks
continuously (press, then press again within
about 1 second and hold); reverse/fast-
forward a track (press and hold).
Radio:
To tune in stations automatically (press); find
a station manually (press and hold).
L Receptor for the card remote
commander
M MODE button 8, 11
To select the radio band (FM/MW/SW);
select the unit* 2 .
N DSPL (display)/DIM (dimmer) button
8
To change display items (press); change the
display brightness (press and hold).
O RESET button (located behind the front
panel) 4
P Frequency select switch (located on the
bottom of the unit)
See "Frequency select switch" in the
supplied installation/connections manual.
Q Number buttons
CD/MD* 1 :
(1)/(2): ALBM –/+* 3 * 4
To skip albums (press); skip albums
continuously (press and hold).
(3): REP 8
(4): SHUF 8
(6): PAUSE* 5
To pause playback. To cancel, press
again.
Radio:
To receive stored stations (press); store
stations (press and hold).
R SCRL (scroll) button 8
To scroll the display item.
Q Q
3 6 7 1 3
Connection example
Notes (2- A )
• Be sure to connect the ground (earth) lead before connecting
the amplifi er.
• The alarm will only sound if the built-in amplifi er is used.
Tip (2- B - )
For connecting two or more CD/MD changers, the source
selector XA-C40 (not supplied) is necessary.
Exemple de raccordement
Remarques (2- A )
• Raccordez d'abord le câble de mise à la masse avant de
raccorder l'amplifi cateur.
• L'alarme est émise uniquement lorsque l'amplifi cateur intégré
est utilisé.
Conseil (2 - B - )
Dans le cas du raccordement de deux changeurs de CD/MD ou
plus, le sélecteur de source XA-C40 (non fourni) est requis.
u163
.
2 9 9 4 2 8
The following buttons on the card remote
commander have also different buttons/functions
from the unit. Remove the insulation film before
use (page 4).
ql < (.)/, (>) buttons
To control CD/radio, the same as (SEEK)
–/+ on the unit.
w; VOL (volume) +/– button
To adjust volume.
wa ATT (attenuate) button
To attenuate the sound. To cancel, press
again.
ws SEL (select) button
The same as the select button on the unit.
wd M (+)/m (–) buttons
To control CD, the same as (1)/(2)
(ALBM –/+) on the unit.
wf Number buttons
To receive stored stations (press); store
stations (press and hold).
*1 When an MD changer is connected.
*2 When a CD/MD changer is connected.
*3 When an MP3/WMA is played.
*4 If the changer is connected, the operation is
different, see page 11.
*5 When playing back on this unit.
Note
If the unit is turned off and the display disappears, it
cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
inserted to activate the unit first.
Tip
For details on how to replace the battery, see
"Replacing the lithium battery of the card remote
commander" on page 14.
1 5 0 5 8 2 9 9 4
m
co
9 9
7
2 8 9 9