Epson Pulsense PS-500 Quick Start

™
Pulsense PS-500

Quick Start

Read these instructions before using your product.
Charge your product
Before using your product for the first time, make sure the
battery is fully charged. Charging takes approximately 2.5 to
3.5 hours. A full charge lasts about 36 hours.
Caution: Do not attach the charging cradle when the PS-500 is
wet. If the PS-500 is wet, wipe it with a damp cloth, remove the
moisture with a towel, then let it air dry before attaching the
charging cradle.
1. Open the charging cradle and insert the PS-500 as shown.
2. Insert the USB plug into a power source. You can use:
■
Computer (using a free USB port)
■
Optional USB AC Adapter (part number SFAC04)
The orange LED lights up
when your PS-500 is
connected correctly.
Charging is complete when
the blue LED is lit.
Install Epson PULSENSE
View
Download
Epson PULSENSE View
device's app store.
The following mobile devices are supported:
■
iPhone 4s, iPhone 5, iPhone 5c, or iPhone 5s with iOS
7.1 or later
■
Mobile device running Android
Bluetooth ® Smart
Launch the app and pair your
PS-500
You must pair your PS-500 through the Epson PULSENSE
View app. This sets the time and date. The PS-500 will not
store any data until you've paired it with the app.
Follow these steps:
1. Start the Epson PULSENSE View app.
2. Make sure that the PS-500 is within 3 feet (1 meter) of the
mobile device.
3. Follow the on-screen instructions to pair your PS-500
with your mobile device and perform the initial
configuration.
The PS-500 can store up to 480 hours of data before needing
to be synced.
App icon Meaning
No network connection. Make sure you have a
network or data connection, then tap the icon to
reconnect.
No Bluetooth connection. Make sure Bluetooth is
enabled on your product and mobile device, then tap
the icon to reconnect.
LED status
The LEDs on the PS-500 light up or flash to indicate different
states. When exercising, the LEDs indicate which zone you're
currently in. The PS-500 vibrates when entering or leaving a
zone.
Light pattern
from your mobile
4.3 or later with
TM
Status
Heart rate is below the fat burning
zone
Heart rate is approaching the fat
burning zone
Heart rate is in the fat burning zone
Light pattern
Wearing and Caring Instructions
Keep these tips in mind when wearing your PS-500:
■
When wearing the PS-500, make sure it does not touch
the ulna bone.
Ulna bone
■
For greater accuracy, wear the PS-500 on your
non-dominant wrist.
■
Tap the watch face to turn on the backlight.
■
Before boarding an aircraft, power off your PS-500 by
selecting from the
Power off
Your Pulsense product is made from materials commonly used
in watches and other consumer products. Since you may wear
your product over extended periods, including when you are
exercising and sweating, it is important that you take care of
your skin and your product according to these instructions.
Prolonged wearing of your product without proper care could
lead to skin irritation or rash.
Please follow the precautions below to ensure full enjoyment
and benefit of your Pulsense product:
1. Keep Pulsense and skin clean
2. Keep Pulsense and skin dry
3. Give skin a rest and some air
See the online User's Guide for more instructions, including
additional instructions on how to wear the band.
Caution: Persons with high skin sensitivity, eczema, allergies,
or asthma may be more likely to experience skin irritation or an
allergic reaction from the Pulsense product or similar products.
Even persons without such conditions may start to experience
redness or skin irritation on wrists from prolonged use or if the
product is not cleaned regularly as indicated above. If you
experience such symptoms:
■
Stop wearing and remove your Pulsense product
immediately. Do not put it back on.
■
If symptoms persist for more than 2-3 days after removing
the Pulsense product, consult a dermatologist.
■
Make sure to follow the wear and care instructions above.
Calibrating your heart rate
To personalize your heart rate zones and calibrate the sleep
monitoring feature, wear your PS-500 for 2 to 7 days while
you sleep. The accuracy of your heart rate zone and sleep data
will improve after the PS-500 has calibrated your resting heart
rate.
Using PULSENSE View
You can view live and collected data, such as heart rate, steps,
calories, and sleep, from your PS-500 using the PULSENSE
View mobile app.
Swipe down for
live heart rate
Settings
Swipe left/
right for
data
overview
If you do not have a mobile device, you can use your
Windows computer to upload data to the PULSENSE View
web application. Download the PS Uploader software
Status
Heart rate is in the aerobic exercise
zone
Heart rate is in the anaerobic
exercise zone
Heart rate is above the anaerobic
exercise zone (flashing rapidly)
settings menu.
System
Refresh
Show data
details
Enter data
Share