Page Introduction 1. Connections 2. Mains Power 3. General Installation NAP 500 4. NAP 500 Installation and Operation 5. NAP 500 Connections NAP 300 6. NAP 300 Installation and Operation 7. NAP 300 Connections NAP 250 8. NAP 250 Installation and Operation 9.
Note: Please read the Statutory Safety Naim Audio products are conceived with performance as the top priority. Careful installation will Warnings found at the help ensure that their full potential is achieved. This manual covers all power amplifiers. It begins end of this manual.
It is essential that repairs and updates are only carried leads. Always use the power switch on the product rather out by an authorised Naim retailer or at the factory by than a mains outlet switch. Naim itself. Many components are custom made, tested or matched and appropriate replacements are often A “thump”...
Switch on the source and preamplifier components, with the volume turned down, before switching on the NAP 500. The NAP 500 power button is located on the front panel of the NAP 500PS Power Supply.
Left Right NAP 500PS NAP 500PS Burndy Burndy NAP 500PS AC ONLY FREQUENCY: 50/60Hz DESIGNED AND MADE IN ENGLAND BY NAIM AUDIO LTD. SOUTHAMPTON ROAD, SALISBURY INPUT POWER: 480VA FUSE RATING: ANTISURGE S/No. Use only 100V TO 120V: T6.3AL. NAP 500 200V TO 240V: T3.15AL/250V.
6.3 Loudspeaker Cable and Connectors Only Naim Audio speaker cable should be used to connect a loudspeaker to the output of the NAP 300. Custom Naim Audio loudspeaker connectors are supplied to make the connection and in order to comply with current European safety regulations these should always be used.
Burndy Burndy NAP 300PS Power supply output Power supply output AC ONLY DESIGNED AND MADE IN ENGLAND BY NAIM AUDIO LTD. DESIGNED AND MADE IN ENGLAND BY NAIM AUDIO LTD. FREQUENCY: 50/60Hz SOUTHAMPTON ROAD, SALISBURY SOUTHAMPTON ROAD, SALISBURY INPUT POWER:...
Only Naim Audio speaker cable should be used to connect The mains earth should always be connected regardless of a loudspeaker to the output of the NAP 250. Custom Naim what other equipment is used. This only grounds the case...
Only Naim Audio speaker cable should be used to connect The mains earth should always be connected regardless of a loudspeaker to the output of the NAP V145. Custom Naim what other equipment is used. This only grounds the case...
NAP 200. The NAP 200 power button is located on the front panel. The NAP 200 can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
NAP 155 XS. The NAP 155 XS power switch is located on the rear panel. The NAP 155 XS can provide power for an appropriate Naim Audio preamplifier. The power supply output is carried on the DIN input socket.
European safety regulations these should order to avoid hum-loops the signal negative of the whole always be used. Naim Audio speaker cable will provide the system should be connected to the mains earth in one place. best results; however, a wide range of speaker cable types can be used without risk of damage to the amplifier.
None None None Dimensions (H x W x D): NAP 500 - 160 x 432 x 375mm NAP 300 - 87 x 432 x 314mm 87 x 432 x 314mm NAP 500PS - 87 x 432 x 314mm NAP 300PS - 87 x 432 x 314mm...
20. Declarations of Conformity Naim Audio declares that Naim Audio products are in conformance with: Low Voltage Directive 2006/95/EC Electromagnetic Compatibility Directive 2004/108/EC Restriction of Hazardous Substances (RoHS2) Directive 2011/65/EU Waste of Electrical and Electronic Equipment Directive 2012/19/EC Energy Using Product Directive 2009/125/EC...