Sharp UP-600 Service Manual page 52

2) LAN CONTROLLER (RTL8019AS)
2)-1. Features:
•
100-pin PQFP
•
Supports PnP auto detect mode
•
Compliant to Ethernet II and IEEE802.3 10Base5, 10Base2,
10BaseT
•
Software compatible with NE2000 on both 8 and 16-bit slots
•
Supports both jumper and jumperless modes
•
Supports Microsofts Plug and Play configuration for jumperless
mode
•
Supports Full-Duplex Ethernet function to double channel band-
width
•
Supports three level power down modes:
– Sleep
– Power down with internal clock running
– Power down with internal clock halted
•
Built-in data prefetch function to improve performance
•
Supports UTP, AUI & BNC auto-detect
•
Supports auto polarity correction for 10BaseT
•
Support 8 IRQ lines
•
Supports 16 I/O base address options
--- and extra I/O address fully decode mode
•
Supports 16K, 32K, 64K and 16K-page mode access to BROM (up
to 256 pages with 16K bytes/page)
•
Supports BROM disable command to release memory after remote
boot
•
Supports flash memory read/write
•
16k byte SRAM built in
•
Use 9346 (64*16-bit EEPROM) to store resource configurations
and ID parameters
•
Capable of programming blank 9346 on board for manufacturing
convenience
•
Support 4 diagnostic LED pins with programmable outputs
2)-2. General Description
The RTL8019AS is a highly integrated Ethernet Controller which of-
fers a simple solution to implement a Plug and Play NE2000 compat-
ible adapter with full-duplex and power down features.
With the three level power down control features, the RTL8019AS is
made to be an ideal choice of the network device for a GREEN PC
system. The full-duplex function enables simultaneously transmission
and reception on the twisted-pair link to a full-duplex Ethernet switch-
ing hub. This feature not only increases the channel bandwidth from
10 to 20 Mbps but also avoids the performance degrading problem
due to the channel contention characteristics of the Ethernet
CSMA/CD protocol.
The RTL8019AS provides the auto-detect capability between the inte-
grated 10BaseT transceiver, BNC and AUI interface. Besides, the
10BaseT transceiver can automatically correct the polarity error on its
receiving pair.
The RTL8019AS is built in with 16K-byte SRAM in a single chip. It is
designed not only to provide more friendly functions but also to save
the effort of SRAM sourcing and inventory.
2)-3. Pin Configuration
66 BA21 [PNP]
67 BA20 [BS0]
68 BA19 [BS1]
69 BA18 [BS2]
70 VDD
71 BA17 [BS3]
72 BA16 [BS4]
73 BA15
74 BA14 [PL0]
75 BCSB
76 EECS
77 BD7 [PL1][EEDO]
78 BD6 [IRQS0][EEDI]
79 BD5 [IRQS1][EESK]
80 BD4 [IRQS2]
81 BD3 [IOS0]
82 BD2 [IOS1]
83 GND
84 BD1 [IOS2]
85 BD0 [IOS3]
86 GND
87 SD15
88 SD14
89 VDD
RTL8019AS
90 SD13
91 SD12
92 SD11
93 SD10
94 SD9
95 SD8
96 IOCS16B [SLOT16]
97 INT7 [IRQ15]
98 INT6 [IRQ12]
99 INT5 [IRQ11]
100 INT4 [IRQ10]
1 INT3 [IRQ5]
2 INT2 [IRQ4]
3 INT1 [IRQ3]
4 INT0 [IRQ2/9]
5 SA0
6 VDD
7 SA1
8 SA2
9 SA3
10 SA4
11 SA5
12 SA6
13 SA7
14 GND
15 SA8
LAN Controller
Signal
No. CPU
name
1 INT3 INT3
2 INT2 INT2
3 INT1 INT1
4 INT0 /INTLAN
5 SA0 LA0
6 VDD +5V
7 SA1 LA1
8 SA2 LA2
9 SA3 LA3
10 SA4 LA4
11 SA5 LA5
12 SA6 LA6
13 SA7 LA7
14 GND GND
15 SA8 LA8
16 SA9 LA9
17 VDD +5V
18 SA10 LA10
19 SA11 LA11
20 SA12 LA12
21 SA13 LA13
22 SA14 LA14
23 SA15 LA15
24 SA16 LA16
25 SA17 LA17
26 SA18 LA18
27 SA19 LA19
28 GND GND
29 IORB /MRD
65 JP
64 AUI
63 LED2 [LED_TX]
62 LED1 [LED_RX] [LED_CRS]
61 LED0 [LED_COL] [LED_LINK]
60 LEDBNC
59 TPIN+
58 TPIN-
57 VDD
56 RX+
55 RX-
54 CD+
53 CD-
52 GND
51 X2
50 X1
49 TX+
48 TX-
47 VDD
46 TPOUT-
45 TPOUT+
44 GND
43 SD7
42 SD6
41 SD5
40 SD4
39 SD3
38 SD2
37 SD1
36 SD0
35 IOCHRDY
34 AEN
33 RSTDRV
32 SMEMWB
31 SMEMRB
30 IOWB
29 IORB
28 GND
27 SA19
26 SA18
25 SA17
24 SA16
23 SA15
22 SA14
21 SA13
20 SA12
19 SA11
18 SA10
17 VDD
16 SA9
I/O Remarks
O N.U. (Pull-Down)
O N.U. (Pull-Down)
O N.U. (Pull-Down)
O Interrupt to CPU
I Address Bus
I Address Bus
I
I
I
I
I
I
I Address Bus
I
I Address Bus
I
I
I
I
I
I
I
I
I
I Memory Read