Operation - Kenwood KX-W8010 Instruction Manual

Timer stand-by
operation
o ¿=
+ f,gf,f,pp!=--
E
-
:ffi"O
KX-W8010
Tuner
Amplifior
t
By using the built-in
TIMER STAND-BY
mechanism
in com-
bination with
an audio timer
(available
from many
dealers),
the
deck
will
begin
to
record or
play at
any desired time.
I
Timer recording
of
radio broadcasts
1.
Connect
the power
cords
to
the components and set
the
timer
so
that power
is
supplied to each component.
(Timer
setting procedures vary with
tho type of timer
used.
Follow the instructions in
the timer's
manual.l
2.
Turn on the
power
switches
of
the
components
to
be
used
for
recording.
3.
Tune in the desired stat¡on and set the recording level.
4.
Set the volume control of the amplifier to
its
minimum
sett¡ng.
5.
Referring to
the
timer's
instruct¡on manual, set the t¡mer
so
that the power will
be
switched
ON
at the
desired
time.
6.
Load
a
taps for recording into
B
deck
or
A deck.
Relay
recording from
B
deck
to A
dsck can also
be
set
by
set-
t¡ng
the
DIRECTION
switch
to
normal
mode
(
=
) or
reverse mode
(
Ð
).
(Refer
to
the "Relay recording")
7.
Set the
DOLBY NR
switch to
B
or
C ¡f
the recording
is
to
be made using the
noise
reduction
system.
8.
Set
rhe
TIMER
swirch
ro
REC.
E)TIMER
REC OFF PLAY
--F
fEEr-l
9.
Power
to the
components
will
be
switched ON at the
proset
time and recording
will start.
10.
Recording
w¡ll stop when
the tape end
is
reached.
Notes:
1,
To encure that tho cassotto deck'e automat¡c shut off switch
opôrato8 before
thc power is shut off,
s6t tho t¡mor so that
it
opôrato8
for a llttlo
longer than tho
play¡ng
time
of
the tape.
2,
When oporst¡ng tho unit other
th¡n
tho CD
playor using
an au-
d¡o
tlmor,
be
sure
to
iomovo tho
d¡sc
from the CD player.
I
Timer playback
1.
Connect
the timer
as
described under
"Timer
record-
ing of
radio broadcasts"
2.
Set the timer
so
that power
is supplied
to
each com-
ponent,
3.
Turn
on
the power switches
of the components
to
be
used
for playback.
4.
Load a recorded tape and set
each
switch referring to
the "Tape playback
operation"
section.
5. Adjust the volume control of the
amplifier.
6.
Rewind
the taps to ths start.
7.
Set the timer
to the
required time.
8.
Ser rhe TIMER
switch
to
PLAY.
oTtMER
!Eq9E5¡!.AI.
l-Ern
9.
The tape
will
automatically start playback at the preset
time.
I
0.
Relay
playback
from
B
deck to A deck can also be set-
ting the
DIRECTION
switch
to
normal mode (
=
l
or
r€vorso mode
(Ð1.
(Refer to the
"Relay playback
operation"l
o
lf tapes are loaded into
both the A and
B
decks, tlmer
playback will
begin
with
the B
deck.
Note:
Audio timer
t
t
To AC outlet
l8
rx-weoro
trnl
Do
not
use a t¡mor
for the dubblng procedure