Advertisement
PROGRAM CONTROL FOR RF OPERATION
Proceed with any control panel programming that may be
necessary for RF operation and the instructions of the system's
wireless transmitters, as described in the control's installation
instructions. In addition, note the following:
• Enable the appropriate control data field for RF usage.
• Enroll the wireless keypad address(es), if used (see instructions
provided with keypad).
• Wireless key buttons must first be enrolled in the control panel
via zone programming, and, where applicable, assigned to a
user number. Enroll each wireless key in 5883H by pressing the
appropriate buttons according to the instructions provided with
the key.
• Upon the successful enrollment of an encrypted key, the red
LED blinks the number of available spaces remaining for
additional encrypted key enrollment (see Checking Available
Space For High Security Keys paragraph).
• If more than one receiver is being used and you are using
encrypted wireless keys, we recommend that you:
a. Enter the GO/NO GO mode.
b. Disconnect one receiver.
c. Enroll all encrypted keys into the connected receiver.
d. Reconnect the disconnected receiver.
e. Exit the GO/NO GO mode.
f. Repeat steps a-e for the receiver that was disconnected.
HIGH SECURITY KEYS & WIRELESS KEYPADS
Depending on the control panel used, the 5883H can support up
to 16 high-security (encrypted) wireless keys and up to 16
wireless keypads. The following paragraphs describe how to:
• Check available space for high-security keys
• How to deactivate all keys
• How to remove all wireless keypads.
See the Control's instructions and the appropriate device
instructions for procedures on enrolling high security keys and
wireless keypads.
Checking Available Space for High Security Keys
The RED LED (above the DIP switch) shows (by blinking) how
many high-security keys may be enrolled into the transceiver.
1. Remove power from the transceiver and set DIP switches:
DIP 1 = ON
DIP 8 = OFF
2. Apply power and observe one of the following RED LED
indications:
a. Blinks, indicating the number of available spaces for
additional high-security key enrollment, and then lights
steady ON.
b. Immediate Steady ON (no blinks), indicating that high-
security key enrollment is full.
c. Off, indicating that no encrypted keys are enrolled.
3. Set DIP switch 1 back to the OFF position to return to normal
receiver operation (leave DIP 8 in OFF position).
Deactivating High-Security keys
This procedure deactivates all enrolled high-security keys and is
required only if previously enrolled high-security keys are being
replaced and there is not enough available space left for them in
the receiver. Once this procedure is performed, all desired high-
security keys must be re-enrolled to activate high-security
operation.
1. Perform steps 1 and 2 in Checking Available Space procedure
above.
2. Wait until the RED LED lights steady ON then:
a. Record the positions of DIP switches 1 through 8.
b. Set DIP switches 1 through 8 to the opposite positions of
their current settings and wait a few moments.
c. Set DIP switches 1 through 8 back to their original positions
as recorded in step a. All enrolled high-security keys will be
deactivated.
3. Set DIP switch 1 back to the OFF position to return to normal
receiver operation (leave DIP 8 in OFF position).
Removing All Wireless Keypads
This procedure removes all wireless keypads from the transceiver.
1. Remove power from the transceiver and set DIP switches:
DIP 1 = OFF
DIP 8 = ON
2. Apply power and observe the RED LED lights steady ON, then:
a. Record the positions of DIP switches 1 through 8.
b. Set DIP switches 1 through 8 to the opposite positions of
their current settings and wait a few moments.
c. Set DIP switches 1 through 8 back to their original positions
as recorded in step a. All enrolled wireless keypads will be
removed from the transceiver.
3. Set DIP switch 8 back to the OFF position to return to normal
receiver operation (leave DIP 1 in OFF position).
NOTE: If unsure that correct RF keypad addresses are enabled in
the receiver, you should perform the RF keypad delete
procedure, then enable RF keypad addresses as described in the
instructions included with the RF keypad. Otherwise, erroneous
ECP device "check" messages may occur.
Page 3 of 4
Hide quick links:
Advertisement
