Advertisement
Quick Links
MediaWalker
RCA male Audio
956 x1
5V/2A Power
adapter x1
Quick Guide x1
(For
3W/5W Speaker)
Warning For better sound quality, this product
contains sharp metal objects, please handle with
care.
3.5mm male to
3.5mm male to
Cable x1
Audio Cable x1
MediaWalker 956
Quick Guide
USB to micro
RCA Female
USB Power
Disc x4
Optical Fiber
Cable x1
Cable x1
Advertisement
Summary of Contents for i-Trinetech MediaWalker 956
-
Page 1: Quick Guide
MediaWalker 956 Quick Guide 3.5mm male to 3.5mm male to USB to micro MediaWalker Optical Fiber RCA male Audio RCA Female USB Power 956 x1 Cable x1 Cable x1 Audio Cable x1 Cable x1 5V/2A Power adapter x1 Quick Guide x1... - Page 2 Plug in the power Use the micro USB power cable to connect the +5V/2A adapter into MediaWalker 956 and turn the power on. ! ! ! ! C onnect the up-link network The default status to the connect up-link is by using a wired Ethernet port.
- Page 3 & & Connect the power with MediaWalker 956 and switch the power on. Wait until the MediaWalker 956 to send out a "Welcome to…………" message, which indicates that the system is ready. Turn on your device such as iPhone, iPad, Android phone and/or computer.
- Page 4 If it can’t find the SSID of the MediaWalker 956 or can’t match the password, please press 5 seconds on the “RESET” button to re-start the MediaWalker 956 back to default setting. 1. Play Music There are several options: a. With the MediaWalker app Click the slide command bar at the upper left corner and choose the Local Player to list the music contents in your Android device.
- Page 5 d. For Windows / Mac User: Install iTune onto Mac/PC via internet. Launch iTunes and click on the middle of top command bar to activate the Airplay. Choose the mw948X_XXXX device to start the WiFi Airplay music. P lay music in USB drive ! ! ! ! ! ! ! ! a.
- Page 6 b. Select ” More” command button, then proceed to the option New list to remote device Input the desired name for the list and press "OK" to create a new list. With the "Remote play-list change" option selected, it would enable you to switch song list to play.
- Page 7 Select the slide command bar at the upper lift corner and select “Setup” to start. Choose “Device Setting” for the configuration setup of MediaWalker 956 Default login Name admin Default login Password admin After logged-in, there will be options: "Network Setup Wizard" and "Network Page...
- Page 8 When a voice "Welcome to ………….." is heard, it indicates that the system is ready to go. Confirm MediaWalker 956 is connected to Internet. Select the slide command bar at the upper lift corner and select “Setup”...
- Page 9 * Note: During firmware upgrade, be sure to keep the product in Power-On and connected to the internet. Wait until MediaWalker 956 restart and sends the “Welcome to……” message, which indicate the firmware upgrade is completed. The steps describe above within this quick guide is only used for MediaWalker APK, please refer to the tutorial pages listed below if you wish to play music through MediaWalker 956 via other UPnP/DLNA.
-
Page 10: Copyright And Trademark Notice
In no event shall i-Trinetech Co., Ltd. be liable to you or any third party for any consequential, incidental, direct, indirect, special, punitive, or other damages (including without limitation, damages for loss of profits, interruptions, loss of information, pecuniary loss, etc.), even if i-Trinetech Co., Ltd. -
Page 11: Fcc Regulation
FCC Regulation 1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.