Summary of Contents for Asus 1U Rackmount Barebone Server RS160-E3/PS4
Page 1
RS160-E3/PS4 1U Rackmount Barebone Server 1U Rackmount Barebone Server 1U Rackmount Barebone Server 1U Rackmount Barebone Server 1U Rackmount Barebone Server User Guide...
Page 2
(including damages for loss of profits, loss of business, loss of use or data, interruption of business and the like), even if ASUS has been advised of the possibility of such damages arising from any defect or error in this manual or product.
Contents Notices ... vii Safety information ... viii About this guide ... ix Chapter 1: Product introduction Chapter 1: Product introduction Chapter 1: Product introduction ... Chapter 1: Product introduction Chapter 1: Product introduction System package contents ... 1-2 System specifications ... 1-3 Front panel features ...
Page 4
Chapter 5: BIOS SETUP Managing and updating your BIOS ... 5-2 5.1.1 AFUDOS Utility ... 5-3 5.1.2 ASUS CrashFree BIOS 2 utility ... 5-6 5.1.3 ASUS Update utility ... 5-8 BIOS setup program ... 5-11 5.2.1 BIOS menu screen ... 5-12 5.2.2...
Page 5
Master ... 5-16 5.3.6 System Information ... 5-17 Advanced menu ... 5-19 5.4.1 CPU Configuration ... 5-19 5.4.2 Chipset Configuration ... 5-21 5.4.3 Onboard Devices Configuration ... 5-23 5.4.4 PCI/PnP Configuration ... 5-27 5.4.5 Power Configuration ... 5-28 5.4.6 Hardware Monitor ... 5-31 Server menu ...
Page 6
7.1.1 Red Hat Enterprise ver. 3.0 ... 7-2 LAN driver installation ... 7-5 7.2.1 Windows 2000/2003 Server ... 7-5 7.2.2 Red Hat Enterprise ver. 3.0 ... 7-7 VGA driver installation ... 7-9 7.3.1 Windows 2000 Server ... 7-9 7.3.2 Windows 2003 Server ... 7-10 7.3.3 Red Hat Enterprise ver.
Notices Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement Federal Communications Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: • This device may not cause harmful interference, and •...
Safety information Electrical Safety Electrical Safety Electrical Safety Electrical Safety Electrical Safety • Before installing or removing signal cables, ensure that the power cables for the system unit and all attached devices are unplugged. • To prevent electrical shock hazard, disconnect the power cable from the electrical outlet before relocating the system.
About this guide Audience Audience Audience Audience Audience This user guide is intended for system integrators and experienced users with at least basic knowledge of configuring a server. Contents Contents Contents Contents Contents This guide contains the following parts: 1 . 1 . C h a p t e r 1 : P r o d u c t I n t r o d u c t i o n C h a p t e r 1 : P r o d u c t I n t r o d u c t i o n C h a p t e r 1 : P r o d u c t I n t r o d u c t i o n...
A S U S S e r v e r W e b - b a s e d M a n a g e m e n t ( A S W M ) u s e r g u i d e This manual tells how to set up and use the proprietary ASUS server management utility.
Page 11
Chapter 1 This chapter describes the general features of the chassis kit. It includes sections on front panel and rear panel specifications.
System specifications The ASUS RS160-E3/PS4 is a 1U barebone server system featuring the ASUS PVL-D/2U/SCSI motherboard. The server supports dual Intel processors with EM64T technology, plus other latest technologies through the chipsets onboard. C h a s s i s...
Page 14
1 x VGA port 2 x USB 2.0 ports 2 x RJ-45 ports (with LEDs) 1 x external SCSI port ASUS Server Web-based Management (ASWM) Voltage, temperature, and fan speed monitoring Automatic System Restart (ASR) feature 650W single power supply, 115V~230V, 50Hz~60Hz 670mm (l) x 448mm (w) x 43.6mm (h)
Front panel features The barebone server displays a simple yet stylish front panel with easily accessible features. The power and reset buttons, LED indicators, location switch, optical drive, and two USB ports are located on the front panel. Refer to section “1.6.1 Front panel LEDs” for the LED descriptions. H o t - s w a p H o t - s w a p H o t - s w a p...
Internal features The barebone server includes the basic components as shown. PCI-X riser card bracket Rear fans ASUS PVL-D/1U/SCSI motherboard Power supply Device fan System fans (4 fans) 1 - 6 1 - 6 1 - 6 1 - 6...
LED information 1.6.1 1.6.1 Front panel LEDs Front panel LEDs 1.6.1 1.6.1 1.6.1 Front panel LEDs Front panel LEDs Front panel LEDs U S B p o r t s U S B p o r t s U S B p o r t s U S B p o r t s U S B p o r t s H D D A c c e s s L E D...
1.6.3 1.6.3 1.6.3 Rear panel LEDs Rear panel LEDs Rear panel LEDs 1.6.3 1.6.3 Rear panel LEDs Rear panel LEDs A C T / L I N K L E D A C T / L I N K L E D A C T / L I N K L E D A C T / L I N K L E D A C T / L I N K L E D...
Page 19
Chapter 2 This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
Chassis cover 2.1.1 2.1.1 2.1.1 Removing the front cover Removing the front cover Removing the front cover 2.1.1 2.1.1 Removing the front cover Removing the front cover Use a Phillips screwdriver to remove the screw on each front end of the top cover.
Firmly hold the cover and slide it toward the rear panel for about half an inch until it is disengaged from the chassis. 1 / 2 i n c h 1 / 2 i n c h 1 / 2 i n c h 1 / 2 i n c h 1 / 2 i n c h d i s t a n c e...
Central Processing Unit (CPU) The motherboard comes with surface mount 604-pin Zero Insertion Force (ZIF) sockets. The sockets are designed for the Intel 604-pin package with 2 MB L2 cache. The new generation Xeon™ processor supports 800 MHz system bus and Extended Memory 64-bit Technology (EM64T).
Page 23
Position the CPU above the socket as shown. Carefully insert the CPU into the socket until it fits in place. The CPU fits only in one correct orientation. DO NOT force the CPU into the socket to prevent bending the pins and damaging the CPU! Carefully push down the socket lever to secure the CPU.
2.2.2 2.2.2 2.2.2 Installing the CPU heatsink Installing the CPU heatsink Installing the CPU heatsink 2.2.2 2.2.2 Installing the CPU heatsink Installing the CPU heatsink To install the CPU heatsink: Carefully place the heatsink on top of the installed CPU. Twist each of the four screws with a Philips (cross) screwdriver just enough to attach the heatsink to...
Always install DIMMs with the same CAS latency. For optimum compatibility, we recommend that you obtain memory modules from the same vendor. Refer to the DDR2 Qualified Vendors List on the ASUS web site. • Due to chipset resource allocation, the system may detect less than 16 GB system memory when you installed eight 2 GB DDR2 memory modules.
2.3.3 2.3.3 2.3.3 Installing a DIMM Installing a DIMM Installing a DIMM 2.3.3 2.3.3 Installing a DIMM Installing a DIMM Make sure to unplug the power supply before adding or removing DIMMs or other system components. Failure to do so may cause severe damage to both the motherboard and the components.
Hot-swap hard disk drives To install a hot-swap HDD: Release a drive tray by pushing the spring lock to the right, then pulling the tray lever outward. The drive tray ejects slightly after you pull out the lever. Firmly hold the tray lever and pull the drive tray out of the bay.
Page 28
Carefully insert the drive tray and push it all the way to the depth of the bay until just a small fraction of the tray edge protrudes. When installed, the SCSI connector on the drive connects to the SCSI connector on the backplane. Refer to section “2.7.2 SCSI backplane” for illustration.
Expansion slot The barebone server comes with a riser card bracket installed on the 64-bit expansion slot. You need to remove the bracket if you wish to install a PCI-X expansion card. 2.5.1 2.5.1 2.5.1 2.5.1 2.5.1 Installing expansion cards Installing expansion cards Installing expansion cards Installing expansion cards...
Page 30
Take note of the holes on the riser card bay. The two pegs on the riser card bracket should match these holes to ensure that the bracket is properly in place. Install the riser card bracket with the card into the PCI-X slot on the motherboard.
2.5.2 2.5.2 2.5.2 Configuring an expansion card Configuring an expansion card Configuring an expansion card 2.5.2 2.5.2 Configuring an expansion card Configuring an expansion card After installing the expansion card, configure the it by adjusting the software settings. Turn on the system and change the necessary BIOS settings, if any. See Chapter 5 for information on BIOS setup.
Cable connections Pre-connected system cables Pre-connected system cables Pre-connected system cables Pre-connected system cables Pre-connected system cables Description 1. Backplane SMBus cable 2. LAN activity LED / Locator LED cable 3. USB cable 4. SCSI cable 5. External SCSI connector 6.
2.6.1 2.6.1 2.6.1 Motherboard Motherboard Motherboard 2.6.1 2.6.1 Motherboard Motherboard The following illustration describes the cables for the specific connectors on the motherboard. LED cable to front panel board SMBus cable to SCSI BP board USBPW34 SCSI cable to BP board 20-pin front panel cable to front panel board USB 2.0 cable to front panel board A S U S R S 1 6 0 - E 3 / P S 4...
2.6.2 2.6.2 2.6.2 SCSI backplane SCSI backplane SCSI backplane 2.6.2 2.6.2 SCSI backplane SCSI backplane The following illustration describes the cables/devices that are connected to the SCSI backplane board. Cable from device fan 8-pin plug from power supply Cable from system fan Cable from system fan Cable from system fan Cable from system fan...
Removable components You may need to remove previously installed system components when installing or removing system devices, or when you need to replace defective components. This section tells how to remove the following components: System/Device fans Power supply module Optical drive 2.7.1 2.7.1 System/Device fans...
2.7.2 2.7.2 2.7.2 Power supply module Power supply module Power supply module 2.7.2 2.7.2 Power supply module Power supply module To remove the power supply module: Disconnect all the power supply plugs connected to all the system devices. Refer to section “2.7 Cable connections” for the locations of pre- connected cables.
2.7.3 2.7.3 2.7.3 Optical drive Optical drive Optical drive 2.7.3 2.7.3 Optical drive Optical drive To uninstall the slim optical drive: Use a Phillips screwdriver (cross) to remove the screw on each end of the top cover. Loosen the two thunbscrews on the rear panel to release the top cover from the chassis.
Then push the front cover as arrow show. Disconnect the LAN activity LED/ Locator LED cable and USB cable from the connectors under the top front cover. Disconnect the IDE cable and the power plug from the connectors on the back of the drive. Then leave the cover as side.
Page 39
Use a Phillips screwdriver (cross) to remove the screw that secures the drive. Carefully slide the optical drive inward for about half an inch, then lift it out of the bay. Remove the screws that secure the optical drive to its metal bracket.
Page 40
2 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 2 - 2 2 C h a p t e r 2 : H a r d w a r e s e t u p C h a p t e r 2 : H a r d w a r e s e t u p C h a p t e r 2 : H a r d w a r e s e t u p C h a p t e r 2 : H a r d w a r e s e t u p...
Page 41
Chapter 3 This chapter describes how to install the optional components and devices into the barebone server.
Rackmount rail kit items If you have the rackmount rail kit, it contains two pairs of rails (one pair for each side of the barebone system), and eight (8) pairs of nut-and-bolt type screws. N u t s N u t s N u t s N u t s N u t s...
Attaching the rails to the rack To attach the rails to the rack: Select one unit of space (1U) on the rack where you wish to install the barebone server. Remove the screws from the 1U space on the rack front. Align the front end holes of a rack rail pair to the 1U space.
Rackmounting the server To mount the server to the rack: Firmly hold the server on both sides and insert the rear panel side to the front end of the rack rail, then carefully push the server all the way to the back until the front panel fits the front end of the rack, and the rack screws on the server match the middle hole on the rack.
Page 45
Chapter 4 This chapter includes the motherboard layout, and brief descriptions of the jumpers and internal connectors.
Page 47
Layout contents Layout contents Layout contents Layout contents Layout contents S l o t s / S o c k e t s S l o t s / S o c k e t s S l o t s / S o c k e t s S l o t s / S o c k e t s S l o t s / S o c k e t s CPU sockets...
Jumpers The grayed out components in the illustrations are present only in PVL-D/SCSI model. 1 . 1 . C l e a r R T C R A M ( C L R T C 1 ) C l e a r R T C R A M ( C L R T C 1 ) C l e a r R T C R A M ( C L R T C 1 ) C l e a r R T C R A M ( C L R T C 1 ) C l e a r R T C R A M ( C L R T C 1 )
Page 49
2 . 2 . C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 ) C P U f a n p i n s e l e c t i o n ( 3 - p i n F M _ C P U 1 , F M _ C P U 2 )
Page 50
4 . 4 . K e y b o a r d p o w e r ( 3 - p i n K B P W R 1 ) K e y b o a r d p o w e r ( 3 - p i n K B P W R 1 ) K e y b o a r d p o w e r ( 3 - p i n K B P W R 1 ) K e y b o a r d p o w e r ( 3 - p i n K B P W R 1 ) K e y b o a r d p o w e r ( 3 - p i n K B P W R 1 )
Page 51
6 . 6 . G i g a b i t L A N c o n t r o l l e r s e t t i n g ( 3 - p i n L A N 1 _ E N 1 ) G i g a b i t L A N c o n t r o l l e r s e t t i n g ( 3 - p i n L A N 1 _ E N 1 ) G i g a b i t L A N c o n t r o l l e r s e t t i n g ( 3 - p i n L A N 1 _ E N 1 ) G i g a b i t L A N c o n t r o l l e r s e t t i n g ( 3 - p i n L A N 1 _ E N 1 )
Page 52
8 . 8 . S C S I c o n t r o l l e r s e t t i n g ( 3 - p i n S C S I _ E N 1 ) S C S I c o n t r o l l e r s e t t i n g ( 3 - p i n S C S I _ E N 1 ) S C S I c o n t r o l l e r s e t t i n g ( 3 - p i n S C S I _ E N 1 ) S C S I c o n t r o l l e r s e t t i n g ( 3 - p i n S C S I _ E N 1 )
Connectors 1 . 1 . F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 ) F l o p p y d i s k d r i v e c o n n e c t o r ( 3 4 - 1 p i n F L O P P Y 1 )
3 . 3 . S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 ) S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
Page 55
4 . 4 . U l t r a 3 2 0 S C S I c o n n e c t o r s ( t w o 6 8 - p i n S C S I A 1 , S C S I B 1 ) U l t r a 3 2 0 S C S I c o n n e c t o r s ( t w o 6 8 - p i n S C S I A 1 , S C S I B 1 ) U l t r a 3 2 0 S C S I c o n n e c t o r s ( t w o 6 8 - p i n S C S I A 1 , S C S I B 1 ) U l t r a 3 2 0 S C S I c o n n e c t o r s ( t w o 6 8 - p i n S C S I A 1 , S C S I B 1 )
Page 56
5 . 5 . H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 ) H a r d d i s k a c t i v i t y L E D c o n n e c t o r ( 4 - p i n H D L E D 1 )
Page 57
7 . 7 . S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 ) S e r i a l p o r t c o n n e c t o r ( 1 0 - 1 p i n C O M 2 )
Page 58
B M C c o n n e c t o r ( 1 6 - p i n B M C C O N N 1 ) This connector is for the ASUS server management card, if available. PVL-D/1U/SCSI BMC connector 1 0 .
Page 59
1 2 . 1 2 . A T X 1 2 . 1 2 . 1 2 . A T X A T X A T X power connectors (24-pin ATXPWR1, A T X power connectors (24-pin ATXPWR1, power connectors (24-pin ATXPWR1, power connectors (24-pin ATXPWR1, 8 8 8 8 8- p i n power connectors (24-pin ATXPWR1, These connectors are for SSI power supply plugs.
Page 60
1 3 . 1 3 . 1 3 . 1 3 . S y s t e m p a n e l c o n n e c t o r ( 2 0 - p i n P A N E L 1 ) 1 3 .
Page 61
1 4 . 1 4 . A u x i l i a r y p a n e l c o n n e c t o r ( 2 0 - p i n A U X _ P A N E L 1 ) 1 4 .
Page 62
4 - 1 8 4 - 1 8 4 - 1 8 4 - 1 8 4 - 1 8 C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n...
Page 63
Chapter 5 This chapter lists the hardware setup procedures that you have to perform when installing or removing system components.
Save a copy of the original motherboard BIOS file to a bootable floppy disk in case you need to restore the BIOS in the future. Copy the original motherboard BIOS using the ASUS Update or AFUDOS utilities. 5 - 2...
M a i n f i l e n a m e Press <Enter>. The utility copies the current BIOS file to the floppy disk. A:\>afudos /oOLDBIOS1.rom AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. Reading flash ... done Write to file...
Updating the BIOS file To update the BIOS file using the AFUDOS utility: Visit the ASUS website (www.asus.com) and download the latest BIOS file for the motherboard. Save the BIOS file to a bootable floppy disk. Write the BIOS filename on a piece of paper. You need to type the exact BIOS filename at the DOS prompt.
Page 67
The utility returns to the DOS prompt after the BIOS update process is completed. Reboot the system from the hard disk drive. A:\>afudos /iI8021A00.100 AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB)) Copyright (C) 2002 American Megatrends, Inc. All rights reserved. WARNING!! Do not turn off power during flash BIOS Reading file ...
ASUS CrashFree BIOS 2 utility ASUS CrashFree BIOS 2 utility The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to restore the BIOS file when it fails or gets corrupted during the updating process. You can update a corrupted BIOS file using the motherboard support CD or the floppy disk that contains the updated BIOS file.
Page 69
Restart the system after the utility completes the updating process. The recovered BIOS may not be the latest BIOS version for this motherboard. Visit the ASUS website (www.asus.com) to download the latest BIOS file. A S U S R S 1 6 0 - E 3 / P S 4...
ASUS Update utility ASUS Update utility 5.1.3 5.1.3 ASUS Update utility ASUS Update utility The ASUS Update is a utility that allows you to manage, save, and update the motherboard BIOS in Windows you to: • Save the current BIOS file •...
Page 71
Updating the BIOS through the Internet Updating the BIOS through the Internet To update the BIOS through the Internet: Launch the ASUS Update utility from the Windows S t a r t S t a r t P r o g r a m s...
Page 72
Updating the BIOS through a BIOS file Updating the BIOS through a BIOS file To update the BIOS through a BIOS file: Launch the ASUS Update utility from the Windows S t a r t S t a r t...
Security Boot [Thu 09/22/2005] [11:10:19] [1.44M, 3.5 in] [ST32122A] [ASUS CD-S520A] [Not Detected] [Not Detected] [Not Detected] [Not Detected] G e n e r a l h e l p G e n e r a l h e l p...
5.2.4 5.2.4 5.2.4 Menu items Menu items Menu items 5.2.4 5.2.4 Menu items Menu items The highlighted item on the menu bar displays the specific items for that menu. For example, selecting M a i n shows the Main menu items. The other items (Advanced, Power, Boot, and Exit) on the menu bar have their respective menu items.
BIOS SETUP UTILITY Server Security Boot [11:10:19] [Mon 09/22/2005] [Disabled] [ST32122A] [ASUS CD-S520A] [Not Detected] [Not Detected] [Not Detected] [Not Detected] M a i n M a i n M a i n M a i n menu screen appears, Exit Use [ENTER].
5.3.4 5.3.4 5.3.4 IDE Configuration IDE Configuration IDE Configuration 5.3.4 5.3.4 IDE Configuration IDE Configuration The items in this menu allow you to set or change the configurations for the IDE devices installed in the system. Select an item then press <Enter> if you wish to configure the item.
5.3.5 5.3.5 5.3.5 Primary/Secondary IDE Master/Slave, Primary/Secondary IDE Master/Slave, Primary/Secondary IDE Master/Slave, 5.3.5 5.3.5 Primary/Secondary IDE Master/Slave, Primary/Secondary IDE Master/Slave, Third, and Fourth IDE Master Third, and Fourth IDE Master Third, and Fourth IDE Master Third, and Fourth IDE Master Third, and Fourth IDE Master The BIOS automatically detects the connected IDE devices.
(C)Copyright 1985-2004, American Megatrends, Inc. Model Name Model Name Model Name Model Name Model Name Displays the auto-detected ASUS motherboard model. Model ID Model ID Model ID Model ID Model ID Displays the auto-detected identification number of the motherboard.
Page 80
Processor Information Processor Information Processor Information Processor Information Processor Information Displays the auto-detected information about the installed CPU or CPUs. Main Processor Information *** CPU1 : Brand Genuine Intel(R) CPU 2.80GHz ID/uCode 0F34h/07h Ratio Value Actual 14 Max 14 Cache Value L1/16KB *** CPU2 : Brand...
Advanced menu The Advanced menu items allow you to change the settings for the CPU and other system devices. Take caution when changing the settings of the Advanced menu items. Incorrect field values can cause the system to malfunction. Advanced Advanced Settings CPU Configuration Chipset Configuration...
Page 82
Single Logical Processor Mode [Disabled] Single Logical Processor Mode [Disabled] Single Logical Processor Mode [Disabled] Single Logical Processor Mode [Disabled] Single Logical Processor Mode [Disabled] Allows you enabled or disabled the single logical processor mode for dual- core CPUs. Configuration options: [Disabled] [Enabled] Hyper-Threading Technology [Enabled] Hyper-Threading Technology [Enabled] Hyper-Threading Technology [Enabled]...
5.4.2 5.4.2 5.4.2 Chipset Configuration Chipset Configuration Chipset Configuration 5.4.2 5.4.2 Chipset Configuration Chipset Configuration The Chipset Configuration menu allows you to change the advanced chipset settings. Select an item then press <Enter> to display the sub-menu. Advanced Advanced Chipset Settings WARNING: Setting wrong values in below sections may cause system to malfunction.
Page 84
NorthBridge Configuration NorthBridge Configuration NorthBridge Configuration NorthBridge Configuration NorthBridge Configuration The NorthBridge Configuration menu allows you to change the Northbridge related settings. Advanced NorthBridge Chipset Configuration DIMM SPEED: DDR2 400 Memory Remap Feature Memory Mirroring/Sparing v02.58 (C)Copyright 1985-2004, American Megatrends, Inc. DIMM Speed DIMM Speed DIMM Speed...
5.4.3 5.4.3 5.4.3 Onboard Devices Configuration Onboard Devices Configuration Onboard Devices Configuration 5.4.3 5.4.3 Onboard Devices Configuration Onboard Devices Configuration Advanced Advanced Onboard Devices Settings USB Configuration Super IO Configuration v02.58 (C)Copyright 1985-2004, American Megatrends, Inc. USB Configuration USB Configuration USB Configuration USB Configuration USB Configuration...
Page 86
Legacy USB Support [Auto] Legacy USB Support [Auto] Legacy USB Support [Auto] Legacy USB Support [Auto] Legacy USB Support [Auto] Allows you to enable or disable support for legacy USB devices. Setting to [Auto] allows the system to detect the presence of legacy USB devices at startup.
Page 87
Super IO Configuration Super IO Configuration Super IO Configuration Super IO Configuration Super IO Configuration Advanced Configure Win83627THF Super IO Chipset Serial Port1 Address Serial Port2 Address Serial Port2 Mode v02.58 (C)Copyright 1985-2004, American Megatrends, Inc. Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4] Serial Port1 Address [3F8/IRQ4]...
Page 88
The following items appear only when the P a r a l l e l P o r t A d d r e s s item is set to [378], [278], or [3BC]. Parallel Port Mode [Normal] Parallel Port Mode [Normal] Parallel Port Mode [Normal] Parallel Port Mode [Normal] Parallel Port Mode [Normal]...
5.4.4 5.4.4 5.4.4 PCI/PnP Configuration PCI/PnP Configuration PCI/PnP Configuration 5.4.4 5.4.4 PCI/PnP Configuration PCI/PnP Configuration The PCI/PnP Configuration menu items allow you to change the advanced settings for PCI/PnP devices. The menu includes setting the IRQ and DMA channel resources for either PCI/PnP or legacy ISA devices, and setting the memory size block for legacy ISA devices.
5.4.5 5.4.5 5.4.5 Power Configuration Power Configuration Power Configuration 5.4.5 5.4.5 Power Configuration Power Configuration The Power Configuration menu items allow you to change the settings for the ACPI and Advanced Power Management (APM) features. Select an item then press <Enter> to display the configuration options. Advanced Power Configuration ACPI APIC Support...
Page 91
APM Configuration APM Configuration APM Configuration APM Configuration APM Configuration Advanced APM Configuration Power Management/APM Video Power Down Mode Hard Disk Power Down Mode Suspend Time Out (Minute) Throttle Slow Clock Ratio Power Button Function Restore on AC Power Loss Power On By PS/2 Keyboard Power On By PS/2 Mouse Power On Ring...
Page 92
Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] Restore on AC Power Loss [Last State] When set to Power Off, the system goes into off state after an AC power loss.
5.4.6 5.4.6 5.4.6 Hardware Monitor Hardware Monitor Hardware Monitor 5.4.6 5.4.6 Hardware Monitor Hardware Monitor Advanced Hardware Monitor CPU1 Temperature CPU2 Temperature MB Temperature CPU1 Fan Speed CPU2 Fan Speed Front1 Fan Speed Front2 Fan Speed Rear1 Fan Speed Rear2 Fan Speed Smart Fan Control CPU1 Temperature CPU2 Temperature...
Page 94
Smart Fan Control [Smart Fan II] Smart Fan Control [Smart Fan II] Allows you to enable or disable the ASUS Q-Fan feature that smartly adjusts the fan speeds for more efficient system operation. Configuration options: [Smart Fan] [Smart Fan II]...
Server menu The Server menu items allow you to customize the server features. Main Advanced Server Server Features Remote Access Configuration v02.58 (C)Copyright 1985-2004, American Megatrends, Inc. Remote Access Configuration Remote Access Configuration Remote Access Configuration Remote Access Configuration Remote Access Configuration The items in this menu allows you to configure the Remote Access features.
Page 96
Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Remote Access [Disabled] Enables or disables the remote access feature. Configuration options: [Disabled] [Enabled] When the R e m o t e A c c e s s items appear.
Security The Security menu items allow you to change the system security settings. Select an item then press <Enter> to display the configuration options. Main Advanced Server Security Settings Supervisor Password : Not Installed User Password : Not Installed Change Supervisor Password v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
Page 98
After you have set a supervisor password, the other items appear to allow you to change other security settings. Main Advanced Security Settings Supervisor Password User Password Change Supervisor Password User Access Level Change User Password Clear User Password Password Check v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
Page 99
Clear User Password Clear User Password Clear User Password Clear User Password Clear User Password Select this item to clear the user password. Password Check [Setup] Password Check [Setup] Password Check [Setup] Password Check [Setup] Password Check [Setup] When set to [Setup], BIOS checks for user password when accessing the Setup utility.
Full Logo display [Enabled] Allows you to enable or disable the full screen logo display feature. Configuration options: [Disabled] [Enabled] Set this item to [Enabled] to use the ASUS MyLogo2™ feature. Bootup Num-Lock [On] Bootup Num-Lock [On] Bootup Num-Lock [On]...
Page 102
Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] Wait for ‘F1’ If Error [Enabled] When set to Enabled, the system waits for the F1 key to be pressed when error occurs.
Exit menu The Exit menu items allow you to load the optimal or failsafe default values for the BIOS items, and save or discard your changes to the BIOS items. Main Advanced Server Exit Options Exit & Save Changes Exit & Discard Changes Discard Changes Load Setup Defaults v02.58 (C)Copyright 1985-2004, American Megatrends, Inc.
Page 104
Load Setup Defaults Load Setup Defaults Load Setup Defaults Load Setup Defaults Load Setup Defaults Select this option then press <Enter> to load the optimized settings for each of the Setup menu items. When a confirmation window appears, select [ O K ] load the default settings.
Page 105
Chapter 6 This chapter provides instructions for setting up, creating, and configuring RAID sets using the available utilities.
Setting up RAID The motherboard comes with the following RAID solutions: PVL-D/1U/SCSI model PVL-D/1U/SCSI model PVL-D/1U/SCSI model PVL-D/1U/SCSI model PVL-D/1U/SCSI model • A d a p t e c A d a p t e c A d a p t e c A d a p t e c ®...
6.1.2 6.1.2 6.1.2 Installing hard disk drives Installing hard disk drives Installing hard disk drives 6.1.2 6.1.2 Installing hard disk drives Installing hard disk drives The motherboard supports SCSI hard disk drives for RAID set configuration. For optimal performance, install identical drives of the same model and capacity when creating a disk array.
Adaptec SCSISelect(TM) Utility! The Adaptec SCSISelect(TM) Utility allows you to create RAID 0, 1, and 0+1 set(s) from SCSI hard disk drives connected to the SCSI connector supported by the Adaptec embedded SCSI controller. To enter the Adaptec SCSISelect(TM) Utility!: Turn on the system after installing all the SCSI hard disk drives.
6.2.1 6.2.1 6.2.1 Configuring the SCSI controller Configuring the SCSI controller Configuring the SCSI controller 6.2.1 6.2.1 Configuring the SCSI controller Configuring the SCSI controller You need to configure the SCSI controller before creating a RAID set. After selecting the SCSI channel to use, the utility prompts you to select from the available options.
The screen returns to the options menu. 6.2.3 6.2.3 6.2.3 Creating a RAID 0 set (Stripe) Creating a RAID 0 set (Stripe) Creating a RAID 0 set (Stripe) 6.2.3 6.2.3 Creating a RAID 0 set (Stripe) Creating a RAID 0 set (Stripe) To create a RAID 0 set for Performance: After enabling the HostRAID, the utility returns to the initial menu.
Page 111
The utility displays the installed SCSI hard disk drives status and menu options. When available, the HDD status shows F r e e The utility does not display an installed SCSI HDD(s) with an existing RAID condiguration or is part of an existing RAID set. Use the SCSI Disk Utilities to reformat the HDD(s), or use the previous RAID card to clear the RAID configuration on the HDD(s).
Page 112
Use the arrow keys to select a RAID set member, then press <SpaceBar> to mark. An X X X X X mark appears after the selected HDD. Follow the step 4 to select the other members of the RAID set, then press <Enter>...
Page 113
If you want to make the array Y e s Y e s bootable, select Y e s Y e s from the Y e s menu, then press <Enter>. When prompted to create the RAID 0 set, select <Yes>, then press <Enter>.
6.2.4 6.2.4 6.2.4 Creating a RAID 1 set (Mirror) Creating a RAID 1 set (Mirror) Creating a RAID 1 set (Mirror) 6.2.4 6.2.4 Creating a RAID 1 set (Mirror) Creating a RAID 1 set (Mirror) To create a RAID 1 set for Fault Tolerance: Follow steps 1 to 2 of the C r e a t i n g a R A I D 0 s e t RAID-1 (Fault Tolerance) RAID-1 (Fault Tolerance)
Page 115
Select C r e a t e n e w R A I D - 1 C r e a t e n e w R A I D - 1 from the RAID-1 Build Option menu, then C r e a t e n e w R A I D - 1 C r e a t e n e w R A I D - 1 C r e a t e n e w R A I D - 1 press <Enter>.
Page 116
11. The utility builds the RAID 1 set and displays a progress bar at the center of the screen. Press <Esc> if you want to stop the building process. A B u i l d C o m p l e t e B u i l d C o m p l e t e B u i l d C o m p l e t e B u i l d C o m p l e t e message...
6.2.5 6.2.5 6.2.5 Creating a RAID 10 set (Stripe+Mirror) Creating a RAID 10 set (Stripe+Mirror) Creating a RAID 10 set (Stripe+Mirror) 6.2.5 6.2.5 Creating a RAID 10 set (Stripe+Mirror) Creating a RAID 10 set (Stripe+Mirror) To create a RAID 10 set for Fault Tolerance and Performance: After enabling the HostRAID, the utility returns to the initial menu.
Page 118
Select R A I D - 1 0 ( F a u l t T o l e r a n c e , H i g h P e r f o r m a n c e ) R A I D - 1 0 ( F a u l t T o l e r a n c e , H i g h P e r f o r m a n c e ) R A I D - 1 0 ( F a u l t T o l e r a n c e , H i g h P e r f o r m a n c e ) R A I D - 1 0 ( F a u l t T o l e r a n c e , H i g h P e r f o r m a n c e ) from the...
Page 119
Select the stripe size from the menu, then press <Enter>. For server systems, we recommend that you use a lower array block size. For multimedia computer systems used mainly for audio and video editing, we recommend a higher array block size for optimum performance. When prompted, use the keyboard to assign a name for the RAID 10 set, then press <Enter>.
Page 120
10. The screen displays the information on the created RAID set. Press <Esc> to exit the utility. 6 - 1 6 6 - 1 6 6 - 1 6 6 - 1 6 6 - 1 6 C h a p t e r 6 : R A I D c o n f i g u r a t i o n C h a p t e r 6 : R A I D c o n f i g u r a t i o n C h a p t e r 6 : R A I D c o n f i g u r a t i o n C h a p t e r 6 : R A I D c o n f i g u r a t i o n...
6.2.6 6.2.6 6.2.6 Adding a spare drive to a RAID 10 set Adding a spare drive to a RAID 10 set Adding a spare drive to a RAID 10 set 6.2.6 6.2.6 Adding a spare drive to a RAID 10 set Adding a spare drive to a RAID 10 set To add a spare drive to a RAID 10 set: Press <S S S S S >...
The screen displays the information on the added spare drive. Press <Esc> to exit the utility. 6.2.7 6.2.7 6.2.7 Deleting a RAID 10 set spare drive Deleting a RAID 10 set spare drive Deleting a RAID 10 set spare drive 6.2.7 6.2.7 Deleting a RAID 10 set spare drive...
Page 123
The screen displays the available spare drive(s). Use the arrow keys to select the spare drive you want to delete, then press <Enter>. When a confirmation dialogue box appears, select <Yes>, then press <Enter> to delete the spare drive. Press <ESC> to exit the utility. A S U S R S 1 6 0 - E 3 / P S 4 A S U S R S 1 6 0 - E 3 / P S 4 A S U S R S 1 6 0 - E 3 / P S 4...
6.2.8 6.2.8 6.2.8 Deleting a RAID set Deleting a RAID set Deleting a RAID set 6.2.8 6.2.8 Deleting a RAID set Deleting a RAID set To delete a RAID set: Press <D D D D D > from the C o n f i g u r e / V i e w H o s t R A I D S e t t i n g s For RAID 0 and RAID 10 set, go to step 3.
6.2.9 6.2.9 6.2.9 Rebuilding a RAID set Rebuilding a RAID set Rebuilding a RAID set 6.2.9 6.2.9 Rebuilding a RAID set Rebuilding a RAID set The rebuild option is available only for RAID 1 and RAID 10 sets. To rebuild a RAID set: From the main menu, select the RAID set you want to rebuild, then press <Enter>.
6.2.10 6.2.10 Verifying a RAID set hard disk drive 6.2.10 Verifying a RAID set hard disk drive Verifying a RAID set hard disk drive Verifying a RAID set hard disk drive 6.2.10 6.2.10 Verifying a RAID set hard disk drive To verify a RAID set hard disk drive: Select S C S I D i s k U t i l i t i e s S C S I D i s k U t i l i t i e s...
Select V e r i f y D i s k M e d i a V e r i f y D i s k M e d i a V e r i f y D i s k M e d i a V e r i f y D i s k M e d i a from the menu, then press <Enter>.
Page 128
Select the RAID set you want to make bootable, then press <Enter>. Press < B > < B > < B > when the RAID set information displays on screen. < B > < B > When prompted, select M a r k b o o t a b l e b o o t a b l e b o o t a b l e...
Page 129
Chapter 7 This chapter provides instructions for installing the necessary drivers for different system components.
RAID driver installation After creating the RAID sets for your server system, you are now ready to install an operating system to the independent hard disk drive or bootable array. This part provides instructions on how to install the RAID controller drivers during OS installation.
Page 131
Select Y e s Y e s Y e s Y e s using the <Tab> key when asked if you have the driver disk. Y e s Press <Enter> Select f d 0 f d 0 f d 0 f d 0 using the <Tab>...
Page 132
When prompted, insert the Red Hat to the floppy disk drive, select O K , The drivers for the RAID controller are installed to the system. When asked if you will load additional RAID controller drivers: • For PVL-D/2U/SCSI model, select Y e s RAID controller drivers (for Adaptec Follow screen instructions to continue the OS installation.
LAN driver installation This section provides instructions on how to install the Broadcom LAN controller drivers. 7.2.1 7.2.1 Windows Windows ® ® ® ® ® 7.2.1 7.2.1 7.2.1 Windows Windows Windows To install the Broadcom ® 2003 Server OS: Restart the computer, then log on with A d m i n i s t r a t o r Insert the motherboard/system support CD to the optical drive.
Page 134
Click N e x t N e x t when the InstallShield Wizard window appears. Follow N e x t N e x t N e x t screen instructions to continue installation. 7 - 6 7 - 6 7 - 6 7 - 6 7 - 6 C h a p t e r 7 : D r i v e r i n s t a l l a t i o n...
7.2.2 7.2.2 7.2.2 Red Hat Red Hat Red Hat ® ® ® ® ® 7.2.2 7.2.2 Red Hat Red Hat Follow these instructions when installing the Broadcom base driver for the Red Hat Installing the source RPM package Installing the source RPM package Installing the source RPM package Installing the source RPM package Installing the source RPM package...
Page 136
Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file Building the driver from the TAR file To build the driver from the TAR file: Create a directory and extract the TAR files: tar xvzf bcm5700-<version>.tar.gz Build the driver bcm5700.o as a loadable module for the running...
VGA driver installation This section provides instructions on how to install the ATI Graphics Adapter (VGA) driver. 7.3.1 7.3.1 7.3.1 Windows Windows Windows ® ® ® ® ® 7.3.1 7.3.1 Windows Windows You need to manually install the ATI 2000 Server operating system. To install the ATI ®...
Page 138
7.3.2 7.3.2 7.3.2 Windows Windows Windows 7.3.2 7.3.2 Windows Windows The Windows ® 2003 Server operating system automatically recognizes the ® RAGE XL VGA driver during system installation. There is no need to install an additional driver(s) to support the onboard VGA. 7.3.3 7.3.3 7.3.3...
The support CD that came with the motherboard package contains the drivers, management applications, and utilities that you can install to avail all motherboard features. The contents of the support CD are subject to change at any time without notice. Visit the ASUS website (www.asus.com) for updates. 7.4.1 7.4.1 7.4.1...
Contact information Click the C o n t a c t C o n t a c t tab to display the ASUS contact information. You can C o n t a c t C o n t a c t C o n t a c t also find this information on the inside front cover of this user guide.