Advertisement
Table of Contents
- 1 General Instructions
- 2 Installation
- 3 Wall and Ceiling Protection
- 4 Using Flexible Vent Components
- 5 Using Rigid Vent Components
- 6 Log Placement
- 7 Optional Blower Installation
- 8 Optional Fan Installation
- 9 Gd36 Thermostatic Sensor Control
- 10 Pilot Burner Adjustment
- 11 Venturi Adjustment
- 12 Terminal Kits
- 13 Troubleshooting Guide
- Download this manual
INST
INST
INSTALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
INST
INST
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
ALLER: THESE INSTRUCTIONS MUST BE CONVEYED TO AND REMAIN WITH THE HOMEOWNER
CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS, CSA 2.22, AND ANSI Z21.50 RESPECTIVELY FOR VENTED GAS FIREPLACES.
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOLT SYSTEM
GAS - DIRECT VENT MILLIVOL
GAS - DIRECT VENT MILLIVOL
W W W W W ARNING:
ARNING: If the information in these instructions is not followed exactly, a fire or
ARNING:
ARNING:
ARNING:
explosion may result causing property damage, personal injury or death.
Do not store or use gasoline or other flammable vapours and liquids in the vicinity of
• Do not try to light any appliance.
• Do not touch any electrical switch.
• Do not use any phone in your building.
Installation and service must be performed by a qualified installer, service
Fax: (705)722-6031
Web: www.napoleon.on.ca
INST
INST
ALLA
ALLA
TION AND OPERA
TION AND OPERA
INSTALLA
INST
INST
ALLATION AND OPERA
ALLA
TION AND OPERATION INSTRUCTIONS FOR
TION AND OPERA
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
VENTED GAS FIREPLACE
NATURAL GAS MODEL
PROPANE GAS MODEL
CERTIFIED FOR CANADA AND UNITED STATES USING ANSI / AGA / CGA METHODS
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
FOR YOUR SAFETY
this or any other appliance.
WHA
WHA
WHAT T T T T T T T T TO DO IF YOU SMELL
WHA
WHA
O DO IF YOU SMELL
O DO IF YOU SMELL
O DO IF YOU SMELL GAS:
O DO IF YOU SMELL
agency or the gas supplier.
Wolf Steel Ltd., RR#1, 9 Napoleon Rd.,
Barrie, ON., Canada L4M 4Y8 (705)721-1212
Email: ask@napoleon.on.ca
T SYSTEM
T SYSTEM
T SYSTEM
T SYSTEM
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
TION INSTRUCTIONS FOR
GD16 - N
GD16 - N
GD16 - N
GD16 - N
GD16 - N
GD16 - P
GD16 - P
GD16 - P
GD16 - P
GD16 - P
GAS:
GAS:
GAS:
GAS:
• Immediately call your gas supplier from
a neighbor's phone. Follow the gas
supplier's instructions.
• If you cannot reach your gas supplier,
call the fire department.
R-2000
1
WS-415-112 / 06.18.99
Advertisement
Table of Contents
Related Manuals for Napoleon GD16 - N
Summary of Contents for Napoleon GD16 - N
- Page 1 • If you cannot reach your gas supplier, call the fire department. Installation and service must be performed by a qualified installer, service agency or the gas supplier. Wolf Steel Ltd., RR#1, 9 Napoleon Rd., Barrie, ON., Canada L4M 4Y8 (705)721-1212 Fax: (705)722-6031 Email: ask@napoleon.on.ca R-2000 Web: www.napoleon.on.ca...
- Page 2 T T T T T ABLE ABLE ABLE of of of of of CONTENTS ABLE CONTENTS CONTENTS ABLE CONTENTS CONTENTS OPTIONAL BLOWER INST OPTIONAL BLOWER INST ALLA ALLA TION TION P G 1 7 OPTIONAL BLOWER INST OPTIONAL BLOWER INST OPTIONAL BLOWER INSTALLA ALLA ALLATION...
- Page 3 After the first year, NAPOLEON will not be responsible for installation, labour or any other costs or expenses related to the reinstallation of a warranted part, and such expenses are not covered by this warranty.
-
Page 4: General Instructions
Do not use abrasive cleaners to clean plated parts. Buff lightly with a clean dry cloth. The glass is 3/16" tempered glass available from your Napoleon / Wolf Steel Ltd. dealer. DO NOT SUBSTITUTE MATERIALS. Clean the glass after the first 10 hours of operation with a recommended gas fireplace glass cleaner. - Page 5 W W W W W ARNING ARNING ARNING ARNING ARNING • • • • • Do not burn wood or other materials in this fireplace. • Adults and especially children should be alerted to the hazards of high surface temperatures and should stay away to avoid burns or clothing ignition.
- Page 6 The air terminal must remain unobstructed at all times. Examine the air terminal at least once a year to verify that it is unobstructed and undamaged. Horizontal runs may have a 0 inch rise per foot using Simpson Dura-Vent, Napoleon rigid or flexible venting components when venting as illustrated in Figure 2a-c.
- Page 7 TERMIN TERMIN AL INST AL INST ALLA ALLA TIONS: TIONS: AIR TERMIN TERMIN TERMINAL INST AL INST AL INSTALLA ALLA ALLATIONS: TIONS: TIONS: FIGURE 4 INSTALLATIONS CANADIAN U.S.A. 12 INCHES 12 INCHES Clearance above grade, veranda porch, deck or balcony. 12 INCHES 9 INCHES Clearance to windows or doors that open.
-
Page 8: Installation
FIGURE 7 VERTICAL INSTALLATION: This application occurs when venting through a roof. FIGURE 2. Installation kits for various roof pitches are available from your Napoleon dealer. See Accessories to order the specific kit required. 1. Determine the air terminal location, cut and frame 9½ inch openings in the ceiling and the roof to provide the minimum 1 inch clearance between the fireplace pipe / liner and any combustible material. -
Page 9: Using Flexible Vent Components
1-1/4" air gap to the 7" outer liner. These spacers must not be removed. 2. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon support ring assemblies, GA-GD-010.370 or equivalent noncombustible strapping to maintain the minimum 1" clear- ance to combustibles WS-415-112 / 06.18.99... - Page 10 VERTICAL VENTING INST TICAL VENTING INST TICAL VENTING INST TICAL VENTING INSTALLA TICAL VENTING INST ALLA ALLA ALLA ALLATION TION TION TION TION FIGURE 13 FIGURE 12 1. Fasten the roof support to the roof using the screws provided. FIGURE 13. The roof support is optional. In this case the venting is to be adequately supported using ei- ther an alternate method suitable to the authority having jurisdiction or the optional roof support.
-
Page 11: Using Rigid Vent Components
HAVE A MINIMUM ¼ INCH RISE PER FOOT. The vent system must be supported approximately every 3 feet for both vertical and horizontal runs. Use Napoleon vent spacers WS-615-33 or equivalent every 3 feet and either side of each elbow to maintain the minimum 1¼" clearance between the outer and inner vent pipes. - Page 12 Elbows and rigid 36" lengths are manufactured with the 4" components per- FIGURE 17 manently fixed within the 7" components. Apply high temperature sealant to both collars and install the assembly as a single unit securing the outer 7" piece with three screws. TICAL VENTING INST TICAL VENTING INST ALLA...
- Page 13 MOBILE HOME INST MOBILE HOME INST ALLA ALLA TION TION MOBILE HOME INST MOBILE HOME INST MOBILE HOME INSTALLA ALLA ALLATION TION TION In Canada, mobile home installation may be vented horizontally or vertically. In the United States, it may only be installed vertically.
- Page 14 For corner installation, allow a minimum rise of 6 inches between the fireplace and the air terminal using Napoleon flexible venting components / 0 inch rise when using Napoleon rigid venting or Simpson Dura-vent compo- nents. FIGURE 2d. Pull out the four nailing tabs, attached on either side of the fireplace and secure to the 2x4 framing to facilitate drywall installation and/or secure the fireplace to the floor using #10 screws (not supplied) using the two ¼"...
-
Page 15: Log Placement
Push in to engage the magnets. The louvre assemblies are installed as illustrated in FIGURE 29. Optional plated door trim, door side trim and arched door facias are available at your local Napoleon / Wolf Steel dealer. -
Page 16: Optional Blower Installation
OPTIONAL BLOWER INSTALLATION INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be electrically connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE Canada or the ANSI/NFPA 70-1996 in the United States NATIONAL ELECTRICAL CODE If the fireplace was not previously equipped with a blower: route a... -
Page 17: Optional Fan Installation
SENSOR ASSEMBLY BRACKET This optional kit is meant to be used only in conjunction with the GD65 Fan Kit, shown above, which may be ordered from your Wolf Steel / Napoleon dealer. RECEPTACLE / With the thermostatic sensor option, the fan, when turned on, becomes... - Page 18 OPERATION / MAINTENANCE OPERA OPERA TING INSTRUCTIONS TING INSTRUCTIONS OPERA OPERATING INSTRUCTIONS OPERA TING INSTRUCTIONS TING INSTRUCTIONS When lit for the first time, the fireplace will emit a slight odour for a few hours. This is a normal temporary condition caused by the curing of the logs and the "burn-in"...
-
Page 19: Pilot Burner Adjustment
6. Check to see that the main burner ignites completely on all openings when the gas knob for the burner is turned on. A 5 to 10 second total light-up period is satisfactory. If ignition takes longer, consult your Napoleon dealer / distributor. -
Page 20: Terminal Kits
ORDERING REPLACEMENT PAR ARTS Contact your dealer or the factory for questions concerning prices and policies on replacement parts. Normally all parts can be ordered through your Napoleon dealer or distributor. When ordering replacement parts always give the following information: 1. M &... - Page 21 ACCESSORIES ACCESSORIES ACCESSORIES ACCESSORIES ACCESSORIES Use only accessories designed for and listed with the GD16 model. PART NO. PART NO. DESCRIPTION DESCRIPTION PART NO. PART NO. PART NO. DESCRIPTION DESCRIPTION DESCRIPTION GD2PB 2" TRIM KIT - POLISHED BRASS GD2AB 2" TRIM KIT - ANTIQUE BRASS GD2C 2"...
-
Page 22: Troubleshooting Guide
TROUBLE SHOOTING GUIDE EFORE ATTEMPTING TO TROUBLESHOOT PURGE YOUR UNIT AND INITIALLY LIGHT THE PILOT AND THE MAIN BURNER WITH THE GLASS DOOR REMOVED SYMPTOM SYMPTOM SYMPTOM SYMPTOM SYMPTOM PROBLEM PROBLEM PROBLEM PROBLEM PROBLEM TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION Pilot... - Page 23 SYMPTOM SYMPTOM PROBLEM PROBLEM SYMPTOM SYMPTOM SYMPTOM PROBLEM PROBLEM PROBLEM TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION TEST SOLUTION Main burner goes Refer to "MAIN BURNER GOES OUT; PILOT STAYS ON" out; pilot goes out. - check for vent blockage. Vent is blocked - check joint seals and installation.
- Page 24 NOTES: WS-415-112 / 06.18.99...