Advertisement
..
.—.. .—. ... .....——_ —-.-.
...----- . ........-— —-—
——.
.-—-—
DISCONNECT THE HOOD POWER SUPPLY
AT TE{E HOUSEHOLD DISTRIBUTION PANEL
BY REMOVING THE FUSE OR SWITCHING
OFF THE CIRCUIT BREAKER.
Remove filter,
Wipe fan blade and motor with cloth, dampened
":.
only in ammonia and warm water solution.
e:
-= " —
.—
i
i
'f
2.
3.
LAMP
SW!TCH
FAN SWITCH
4.
Replace filter.
Reconnect the hood power supply.
~~mp switch
For
models, JV322 and JV332, switch has OFF and
ON positions. For other models, press ONCE for
NORMAL LIGHT. Press again for NIGHT LIGHT.
Press THIRD TIME for OFF.
5.
Lamp Replacement
—1
Models JV324, JV624,
JV334 and JV634 have a
lamp cover.
The lamp cover need not be
removed for lamp removal
or installation.
Fan
switch
Press ONCE
for
HIGH
speed.
Press TWICE for
LOW SPEED. Press again for OFF.
Y' &_----l
To Maintain
CAUTION: Let lamp coo! completely before
removing. A warm or hot bulb may break if
touched with a moist cloth or hand.
Gnwx? Filter
The efficiency of your hood depends on a clean
filter. Frequency of cleaning depends on the type
of cooking you do. BUT GREASE FILTER
SHOULD BE CLEANED AT LEAST ONCE
A MONTH. NEVER OPERATE THE HOOD
WITHOUT THE FILTER IN PLACE.
Remove lamp and replace with an ordinary screw-
base lamp bulb NOT MORE THAN 60 WATTS.
To remove lamp cover, if desired:
@Press the sides with two fingers until the side
prongs are released.
@Lift lamp cover and slide towards you in one
To remove: Press outward on spring clip, pull
down and snap out filter.
To clean: Soak and then agitate in a hot detergent
solution. Light brushing may be used to remove
imbedded soil. Rinse, shake and remove moisture
before replacing.
With careful handling, the filter will last for years.
If replacement becomes necessary, order part
number WB2X2052from your dealer.
6
motion.
To replace lamp cover:
@ Insert prong located at end of cover into top
opening.
@Gently push cover up and press sides to fit side
prongs into the side openings.
To replace: Put the filter rim in and against two
clips, push outward on the third clip and press
filter upward into place.
@Release and the cover will lock in position.
Before
You
call
for
Sewice
i-food
Clean grease laden surfaces of the hood fre-
quently. Use warm detergent solution. About
1 tablespoon of ammonia may be added to the
water. TAKE CARE TO NOT COME IN CONTACT
WITH FILTERS AND OTHER NON-ENAMELED
SURFACES. The hood shell can be washed, rinsed
If the fan does not operate when the switch is
on, check the hood power supply at the house-
hold distribution panel. A fuse may be blown or
a circuit breaker tripped.
If the fan fails to circulate air, possible causes
such as the fan blade striking the hood shell or
excessively soiled filter should be checked
and
corrected before using the hood again.
If the fan operates but moves air slower than
normal, check to be sure the filter is clean. If
that does not correct the problem, call for
service.
If the fan keeps going off and on, the motor is
probably overheating and turning itself off. This
and dried with a soft cloth.
CAUTiON: Be certain when cleaning hood
surfaces you do not touch lamp bulb with
moist hands or cloth. A warm or hot lamp
bulb may break if touched with a moist sur-
face. ALWAYS let lamp cool COMPLETELY
before cleaning around it.
can be harmful to th= motor.
Check to be sure
the
filter is clean. if off and on cycling con-
tinues, call for service.
Advertisement
