1. Manuals
  2. Brands
  3. Mitsubishi Manuals
  4. PCI Card
  5. Q80BD-J71GP21S-SX
  6. User manual

Mitsubishi Q80BD-J71GP21S-SX User Manual

Cc-link ie controller network interface board
Hide thumbs
Table of Contents

Advertisement

Quick Links

Controller Network
Interface Board
Q80BD-J71GP21S-SX
Thank you for purchasing the Mitsubishi program logic controller
MELSEC-Q series.
Prior to use, please read this and relevant manuals thorougly to fully
understand the product.
© 2007 MITSUBISHI ELECTRIC CORPORATION
CC-Link IE
Q80BD-J71GP21-SX
MODEL
MODEL
CODE
IB(NA)-0800386-D(0809)MEE
User's Manual
(Hardware)
MNETG-B-SW1-H
13JY32

Advertisement

Table of Contents
loading

Summary of Contents for Mitsubishi Q80BD-J71GP21S-SX

  • Page 1 CC-Link IE Controller Network Interface Board User’s Manual (Hardware) Q80BD-J71GP21-SX Q80BD-J71GP21S-SX Thank you for purchasing the Mitsubishi program logic controller MELSEC-Q series. Prior to use, please read this and relevant manuals thorougly to fully understand the product. MODEL MNETG-B-SW1-H MODEL...

  • Page 2: Safety Precautions

    SAFETY PRECAUTIONS (Be sure to read these instructions before using the product.) Before using this product, read this manual and the relevant manuals introduced in this manual carefully and handle the product correctly with full attention to safety. Note that these precautions apply only to this product. Refer to the user's manual of your CPU module for safety precautions on programmable controller systems.
  • Page 3 [Installation Precautions] DANGER Do not touch connectors while current is applied. Doing so may cause an electric shock or malfunction. Be sure to shut off all phases of the external power supply used by the system before installing the CC-Link IE Controller Network board to or removing it from the personal computer.
  • Page 4 Special skills and tools are required to connect the communication cable to the connector plug, which is an exclusive product. When purchasing it, please consult your local Mitsubishi representative. Incomplete connection can result in a short, fire or malfunction. Securely plug the communication cable to the connector of the CC-Link IE Controller Network board.
  • Page 5 [Wiring Precautions] CAUTION Insert the wired external power supply cable into the external power supply cable connector until a click is heard. Imperfect insertion may cause a failure or malfunction. Keep the external power supply cable away from the main circuit cable, power cables and/or the load cables for any other than programmable controllers.
  • Page 6 This manual confers no industrial property rights or any rights of any other kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual.

  • Page 7: Table Of Contents

    CONTENTS 1. OVERVIEW..................... 1 2. PERFORMANCE SPECIFICATIONS ............. 2 3. HANDLING ..................... 4 3.1 Handling precautions ................4 3.2 Installation environment................6 4. PART NAMES....................7 5. EMC AND LOW VOLTAGE DIRECTIVE ............10 5.1 Requirements for conformance to EMC Directive ........10 5.1.1 Standards applicable to the EMC Directive........
  • Page 8 Manual The following is the manual relevant to this product. Please purchase it if necessary. Relevant Manuals Manual Number Manual Name (Model Code) MELSECNET/G Network System Reference Manual (Controller Network) This manual explains the system configuration, performance SH-080668ENG specification, functions, handling and wiring instructions, and (13JV16) troubleshooting of the CC-Link IE Controller network system.

  • Page 9: Overview

    CC-Link IE Controller network system. The packing list of the CC-Link IE Controller Network board is given below. Quantity Item Q80BD-J71GP21-SX Q80BD-J71GP21S-SX Q80BD-J71GP21-SX CC-Link IE Controller Network interface — board Q80BD-J71GP21S-SX CC-Link IE Controller Network interface —...

  • Page 10: Performance Specifications

    2. PERFORMANCE SPECIFICATIONS Performance specifications of the CC-Link IE Controller Network board are shown below. Q80BD-J71GP21-SX, Q80BD-J71GP21S-SX Specification Item Q80BD-J71GP21-SX Q80BD-J71GP21S-SX 32K points (32768 points, 4K bytes) 128K points (131072 points, 256K bytes) Max. link points per network 8K points (8192 points, 1K byte)
  • Page 11 Specification Item Q80BD-J71GP21-SX Q80BD-J71GP21S-SX Number of boards that can be Up to 4 installed Installation slot PCI bus slot (Half size) or PCI-X bus slot (Half size) Occupied slots 1 slot Voltage 20.4 V to 31.2 V DC Current 0.27 A...

  • Page 12: Handling

    3. HANDLING This section explains precautions for handling and installation environment of the CC-Link IE Controller Network board. 3.1 Handling precautions The following explains precautions for handling the CC-Link IE Controller Network board. Do not touch connectors while current is applied. DANGER Doing so may cause an electric shock or malfunction.
  • Page 13 Securely insert the CC-Link IE Controller Network board CAUTION into the PCI bus slot following the board installation instruction of the personal computer. Incorrect insertion of the CC-Link IE Controller Network board may lead to a malfunction, failure or drop of the board.

  • Page 14: Installation Environment

    3.2 Installation environment For installation of the personal computer in which the CC-Link IE Controller Network board is installed, refer to the manual for the personal computer. Use the CC-Link IE Controller Network board in an CAUTION environment that meets the general specifications provided in this manual.

  • Page 15: Part Names

    4. PART NAMES This section explains each part name and setting of the CC-Link IE Controller Network board. (1) Q80BD-J71GP21-SX RUN ERR. BD808C 317G51 (2) Q80BD-J71GP21S-SX E.PW E.PW ERR. E.PW +24VDC BD808C 317G51...
  • Page 16 Name Description Indicates the operating status of the CC-Link IE Controller Network board. The display format has three types: normal mode, error mode and channel number confirmation. (1) Normal mode When the RUN LED is OFF or ON, the LED display becomes normal mode.
  • Page 17 Name Description Connector for connecting optical fiber cable (1) The cable terminal is as shown below. IN Reverse loop transmission IN Forward loop reception Optical fiber cable connector OUT Forward loop transmission OUT Reverse loop reception (2) For wiring of an optical fiber cable, refer to "CC-Link IE Controller Network Interface Board User's Manual (For SW1DNC-MNETG-B)".

  • Page 18: Emc And Low Voltage Directive

    5. EMC AND LOW VOLTAGE DIRECTIVE For the products sold in European countries, the conformance to the EMC Directive, which is one of the European Directives, has been a legal obligation since 1996. Also, conformance to the Low Voltage Directive, another European Directive, has been a legal obligation since 1997.

  • Page 19: Standards Applicable To The Emc Directive

    5.1.1 Standards applicable to the EMC Directive The standards applicable to the EMC Directive are listed below. All test items were tested by installing each device on a personal computer bearing a CE certification logo. Specification Test item Test details Standard value Measures 30M-230MHz QP: 30 dB...

  • Page 20: Installing Devices In The Control Panel

    5.1.2 Installing devices in the control panel Installing devices in the control panel has a considerable effect, not only securing safety but also shielding the noise generated from the personal computer in the control panel. (1) Control panel (a) Use a conductive control panel. (b) When attaching the control panel's top plate or base plate, mask painting and weld so that good surface contact can be made between the panel and plate.
  • Page 21 (2) Connection of power and ground cable The power supply cable and ground cable for a personal computer should be laid out as follows: (a) Provide a grounding point near the power supply of personal computer. Ground the FG (frame ground) terminal of the personal computer and the SLD (shield) terminal of the CC- Link IE Controller Network board with the thickest and shortest grounding wire (wire for grounding) possible (about 30 cm...

  • Page 22: Noise Filter (Power Supply Line Filter)

    5.1.3 Noise filter (power supply line filter) A noise filter is a component which has an effect on conducted noise. It is not required to fit the noise filter to the power supply line, but fitting it can further suppress noise. (The noise filter has the effect of reducing conducted noise of 10MHz or less.) The precautions required when installing a noise filter are described below.

  • Page 23: Wiring

    6. WIRING This section explains precautions for connecting cables to the CC-Link IE Controller Network board. (1) Precautions for general wiring Be sure to shut off all phases of the external power supply DANGER used by the system before installing the CC-Link IE Controller Network board or starting wiring.
  • Page 24 Special skills and tools are required to connect the CAUTION communication cable to the connector plug, which is an exclusive product. When purchasing it, please consult your local Mitsubishi representative. Incomplete connection can result in a short, fire or malfunction.
  • Page 25 (3) Precautions for external power supply cable wiring Verify the rated voltage and pin-out, and connect the CAUTION external power supply cable properly. Connecting a power supply with a different voltage rating, imperfect cable crimping or faulty wiring may cause a fire or failure.

  • Page 26: Optical Fiber Cable

    (a) Use the dedicated optical fiber cable shown below for the controller network system. Type Model name (maker) Multi-mode fiber (GI) QG series (Mitsubishi electric system & service Co., Ltd.) (b) When connecting an optical fiber cable to the Q80BD- J71GP21-SX and Q80BD-J71GP21S-SX, the cable bend radius is restricted.

  • Page 27: External Power Supply Cable

    6.2 External power supply cable This section explains the method for connecting external power supply cable to the Q80BD-J71GP21S-SX. (1) Parts and tools required for external power supply cable The following parts and tools are required for making external power supply cable.
  • Page 28 (c) Connecting to the connector According to the following Connector pin-out, fully insert the crimped cable to the connector until a click is Contacting pin heard. Pin No. Description Open (3) Connecting external power supply cable to the board Properly insert the wired external power supply cable to the external power supply cable connector of the Q80BD-J71GP21S- SX until a click is heard.

  • Page 29: Installing Software Packages

    7. INSTALLING SOFTWARE PACKAGES This chapter explains about installing the software packages and icons to be registered. For the uninstallation method, refer to "CC-Link IE Controller Network Interface Board User's Manual (For SW1DNC-MNETG-B)". 7.1 Installation procedures For details of the installation procedure, refer to "CC-Link IE Controller Network Interface Board User's Manual (For SW1DNC-MNETG-B)".
  • Page 30 START Power OFF the personal computer. Install the CC-Link IE Controller Network board to the personal computer. Power ON the personal computer. Install SW1DNC-NMETG-B (driver). Install SW1DNC-NMETG-B (utility).

  • Page 31: Icons To Be Registered

    7.2 Icons to be Registered After installing the software packages, the icons shown below are registered in [MELSEC], selected from [Start] - [Program]. Remarks When using Windows XP Professional/Windows XP Home Edition/ Windows Vista , the following icons are registered in [Start] - [All Programs] - [MELSEC].

  • Page 32: External Dimensions

    8. EXTERNAL DIMENSIONS (1) Q80BD-J71GP21-SX 174.5 (6.87) 181 (7.13) 168 (6.61) RUN ERR. BD808C 317G51 18.5 (0.73) (Unit: mm (inch))
  • Page 33 (2) Q80BD-J71GP21S-SX 174.5 (6.87) 181 (7.13) 168 (6.61) E.PW E.PW ERR. E.PW +24VDC BD808C 317G51 18.5 (0.73) (Unit: mm (inch)) Microsoft and Windows are registered trademarks of Microsoft Corporation in the United States and other countries. Ethernet is a registered trademark of Xerox.co.ltd in the United States.
  • Page 34 Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi; machine damage or lost profits caused by faults in the Mitsubishi products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi;...

This manual is also suitable for:

Q80bd-j71gp21-sx

Table of Contents