Related Manuals for Samsung MWR-WS00
Summary of Contents for Samsung MWR-WS00
- Page 1 USER’S MANUAL Wired Remote Controller MWR-WS00 System Air Conditioner G R A DB98-25179A(1)
-
Page 2: Safety Precautions
Safety Precautions • Before using the wired remote controller, read carefully these instructions. • After reading the instructions, keep this user's manual in a handy and safe place. If a user is changed, you must hand over the manuals. • Never attempt to install the air conditioning system or to move the wired remote controller by yourself. -
Page 3: Table Of Contents
Contents IRED EMOTE ONTROLLER ............ ETTING TARTED ................ ELECTING THE UTOMATIC PERATING ODE ...... ODE ............ ELECTING THE OOLING ELECTING THE EATING ODE ............ ELECTING THE EHUMIDIFYING ODE ........ ODE ............ELECTING THE ... -
Page 6: Ontroller
Selecting the Automatic Operating Mode The room temperature and the fan speed are controlled automatically in the auto mode. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). Result: ... -
Page 7: Selecting The Cooling Mode
Selecting the Cooling Mode Select the cooling mode to lower the room temperature. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). Result: T he air-conditioner will be turned on with the mode selected when the unit was last used. -
Page 8: Selecting The Heating Mode
Selecting the Heating Mode The heating mode can be selected only on the heat pump models. Select the heating mode to raise the room temperature. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). -
Page 9: Selecting The Dehumidifying Mode
Selecting the Dehumidifying Mode Select the dehumidifying mode if the room is too humid. Using this mode will slightly lower the room temperature. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). -
Page 10: Selecting The Fan Mode
Selecting the Fan Mode Select the fan mode to circulate air without changing the temperature. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). Result: T he air-conditioner will be turned on with the mode selected when the unit was last used. -
Page 11: Selecting The Quiet Mode
Selecting the Quiet Mode Select the quiet mode to run the indoor unit as quietly as possible. The quiet mode is used with other operating modes such as the cooling and heating modes. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). -
Page 12: Selecting The Sleep Mode
Selecting the Sleep Mode Select the sleep mode to sleep in comfort without worrying to turn off the air-conditioner in the middle of the night. The air-conditioner will turn off automatically after 6 hours. Press the (ON/OFF) button to turn on the indoor unit. (Do not press the (ON/OFF) button if the remote controller is on). -
Page 13: Adjusting The Airflow Direction
Adjusting the Airflow Direction Adjust the airflow direction to circulate the air according to various needs. By adjusting the airflow direction, the efficiency of the air-conditioner can be increased. Note The airflow direction cannot be set on duct type indoor units. If the indoor unit supports 5-step directions: ... -
Page 14: Checking The Room Temperature
Checking the Room Temperature Press the button to check the room temperature. Result: T he room temperature will be displayed for 3 seconds and return to set temperature display. Note The room temperature may be slightly different depending on the installation location of the remote controller. -
Page 15: Setting The 7-Day Schedule
Setting the 7-day Schedule Set the 7-day schedule to reserve the on/off timer to be repeated every week. At most 10 schedules may be set for each day. Press the button to set a schedule. Result: The day is set to Monday and the schedule number displays the next empty schedule number for that day. -
Page 16: Setting And Canceling A Holiday Schedule
Setting and canceling a Holiday Schedule Schedules need not be deleted when there’s a holiday. Instead, the holiday can be set to stop the schedule from running for the set holiday while keeping the schedule information. Press the button to enter the schedule setup mode. The button does not need to be pressed if the mode is already in schedule setup mode. -
Page 17: Canceling During Schedule Setup
Canceling during Schedule Setup You can cancel the schedule setup at any point during setup as long as the button is not pressed. At any point during schedule setup, press the button. Result: The schedule is canceled. Deleting a Schedule Schedules may be deleted one at a time. -
Page 18: Resetting The Clock
Resetting the Clock Reset the clock to change the time if needed. Press the button shortly. Result: The clock starts blinking. Set the time by pressing the button and button. Result: Each time the button is pressed, the time is increased by 1 hour. ... -
Page 19: Initializing The Remote Controller
Initializing the Remote controller The remote controller can be initialized to the default factory settings. Press the button for 5 seconds. Result: T he clock is initialized and all the schedules are deleted. Note Initializing the remote controller will delete all the schedules and will reset the clock. -
Page 20: Setting The Auto Stop Function
Setting the Auto Stop Function The wired remote controller can be set to turn off the indoor unit(s) after a set period of time has passed since any button on the remote controller was last pressed. This function is used to turn off the indoor unit in case the user forgets to turn off the indoor unit. -
Page 21: Setting The Temperature Limits
Setting the temperature limits The wired remote controller can be set to allow only a certain temperature range. By setting the lower and upper temperature limits, the set temperature can be selected only within the set range. This function may be used for energy savings. Press the button for 5 seconds to enter the setup mode.