Table of Contents
Advertisement
Available languages
Available languages
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed
Tape measure
¼" (6.35 mm) nut driver
Level
Parts supplied
Foam strip
Parts needed
A UL listed or CSA approved conduit connector
UL listed wire connectors
Check local codes. Check existing electrical supply. See
"Electrical Requirements."
It is recommended that all electrical connections be made by a
licensed, qualified electrical installer.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances. When
installing cooktop, use minimum dimensions given.
To eliminate the risk of burns or fire by reaching over the
heated surface units, cabinet storage space located above the
surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a range hood
that projects horizontally a minimum of 5" (12.7 cm) beyond
the bottom of the cabinets.
The cooktop must be a specified cooktop that is approved to
be installed either alone or over an undercounter built-in oven.
Check the cooktop base for an approved installation label. If
you do not find this label, contact your dealer to confirm that
your cooktop is approved.
Ovens approved for this type of installation will have an
approval label located on the top of the oven. If you do not
find this label, contact your dealer to confirm that your oven is
approved. Refer to oven manufacturer's Installation
Instructions for approval for built-in undercounter use and
proper cutout dimensions.
The cooktop should be installed away from strong draft areas,
such as windows, doors, fans or strong heating vents. The
cooktop should be located for convenient use in the kitchen.
Use the countertop opening dimensions that are given with
these Installation Instructions. Given dimensions are minimum
clearances and provide 0" (0 cm) clearance.
Grounded electrical supply is required. See "Electrical
Requirements" section.
IMPORTANT: To avoid damage, check with your builder or
cabinet supplier to make sure that the materials used will not
discolor, delaminate or sustain other damage.
2
INSTALLATION REQUIREMENTS
Marker or pencil
Pliers
Product Dimensions
B
A
A. 21½" (54.6 cm)
B. 30" (76.2 cm) models - 30" (76.2 cm)
36" (91.4 cm) models - 35
C. 3¾" (9.5 cm)
Cabinet Dimensions
IMPORTANT: If installing a range hood or microwave hood
combination above the cooktop, follow the range hood or
microwave hood combination installation instructions for
dimensional clearances above the cooktop surface.
C
J
"
"
A. 30
(76.2 cm) on 30
models; 36
B. Combustible area above countertop (shown by dashed box
above)
"
C. 30
(76.2 cm) minimum clearance between top of cooktop
platform and bottom of unprotected wood or metal cabinet
"
(24
[61 cm] minimum clearance if bottom of wood or metal
cabinet is protected by not less than
retardant millboard covered with not less than No. 28 MSG
"
sheet steel, 0.015
[0.04 cm] stainless steel, or 0.024
"
aluminum or 0.020
[0.05 cm] copper)
"
D. 13
(33 cm) recommended upper cabinet depth
"
E. 2
(5.4 cm)
" +/-
"
F. 20
(51.75 +/- 0.16 cm)
G. 18" (45.7 cm) minimum clearance from upper cabinet to
countertop within minimum horizontal clearances to cooktop
H. Junction box or outlet: 6" (15.2 cm) minimum from top of
counterop; 7" (17.8 cm) maximum from right side of cabinet
"
I. 29
" +/-
(73.8 +/- 0.16 cm) on 30" (76.2 cm) models
"
34
" +/-
(87.8 +/- 0.16 cm) on 36" (91.4 cm) models
J. 1" (2.5 cm) minimum distance to nearest left and right side
combustible surface above cooktop
" (89.7 cm)
A
D
B
F
G
E
H
H
I
"
"
(91.4 cm) on 36
models
"
[0.6 cm] flame
"
[0.06 cm]
C
Advertisement
Table of Contents
