Siemens C35 series Service Manual
  1. Manuals
  2. Brands
  3. Siemens Manuals
  4. Cell Phone
  5. C35 series
  6. Service manual

Siemens C35 series Service Manual

Local service organization
Hide thumbs
Table of Contents

Advertisement

Quick Links

Local Service Organization Service Manual
C
3
5
S
e
r
i
e
s
C
3
5
S
e
r
i
e
s
C
3
5
S
e
r
i
e
s
6 , ( 0 ( 1 6 & 2 0 0 8 1 , & $ 7 , 2 1 6 8 1 / , 0 , 7 ( '
V1.0

Advertisement

Table of Contents
loading

Related Manuals for Siemens C35 series

Summary of Contents for Siemens C35 series

  • Page 1 Local Service Organization Service Manual 6 , ( 0 ( 1 6 & 2 0 0 8 1 , & $ 7 , 2 1 6 8 1 / , 0 , 7 ( ' V1.0...

  • Page 2: Table Of Contents

    C H A P T E R 2 Running the test sequence Level 2 Service Guide ANNEX A Introduction ANNEX B C35 Series Technical Information Accessories C H A P T E R 4 Level 2.5 Repair Document General Information C35 Series Exploded Diagram...

  • Page 3: Cellular Communication

    Chapter Cellular Communication Coverage Concept he cellular systems is made up of numerous transmitting and receiving sites, whose individual coverage areas partially overlap. The concept of frequency re-use, same frequency is used by several sites, allows a high traffic density in a wide area. Due to the limited transmission range of the terminals, cellular systems are based on a large number of base stations on the infrastructure side, scattered over the area to cover, with each covering a fairly small geographical zone called cell.

  • Page 4: Gsm Network Architecture

    GSM Network Architecture. GSM network can be broadly divided into three broad parts, namely: 1. Mobile Station(MS) carried by the subscriber, 2. Base Station Sub-system(BSS) which controls the radio link with the mobile station. 3. Mobile Switching Center(MSC) which performs the switching of calls between the mobile users, and between mobile and fixed network users.

  • Page 5: Subscriber Identity Module

    The subscriber information, which includes a unique number called the International Mobile Subscriber Identity (IMSI) is stored in the SIM card. SIM card identifies the subscriber to the network. FIGURE 1.3 INSERT SIM CARD Figure 1.3 illustrates the steps for inserting the SIM card into the C35 series. V1.0...

  • Page 6: Sim Application Toolkit

    To protect the SIM card from improper use, a security feature, a four digits personal identification number (PIN), is built in. The PIN is stored in the card and can be changed by the subscriber. PIN2 is required for additional funtions available with a special SIM card (Consult the operator for more information about the PIN.

  • Page 7: Extended Gsm 900 - Egsm

    • Mobile Receive: 925 – 960 MHz C35 series is a GSM Phase 2 / Phase 2+ Dualband E-GSM / GSM 1800 mobile phone. Built-in Modem. C35i has an integrated modem for direct data communication using the data cable as shown in Figure 1.5.

  • Page 8: Data Application

    Data Application Support Modem driver conforms to V.25 command set, and transmission speed conforms ITU-T- standard of V.22bis. (2400, 4800,and 9600 bits/sec). Facsimile conforms to Service Class 1, group 3 and operate at 2400, 4800, 7200 and 9600 bit/s. Data services via GSM network up to 9600 bps, and remote control using cellular AT commands for C35i only.

  • Page 9: Level 2 Service Guide

    Chapter Level 2 Service Guide Introduction The chapter is intended to help you carry out repair up to Level 2 on the C35 series mobile phone. The repair for international version and Asian variants are identical unless otherwise noted, therefore the description herein is confined to C35 only.

  • Page 10: C35 Series Technical Information

    C35 & C35i Technical Information System GSM Phase 2/Phase2+, Dual Band EGSM 900, Class 4(2 Watt) GSM 1800, Class 1(1 Watt) Operating Voltage 3.6V Size(LxWxH) 118 x 46 x 21 mm(without antenna) Volume 88cm including battery (approx) Weight 116g including battery (approx) Battery(Standard) NiMH, 500mAH(Standard) Li-Ion, 600mAH(Optional)
  • Page 11 PIN control PIN 1 & 2 Code Control Phone code 4 to 8 digit code Network function Automatic and manual network selection Chipset Siemens E – GOLD WAP Browser Version 1.1 Other Features Clock / Alarm Alarm List Built-in modem...

  • Page 12: Accessories

    Accessories: 1. Standard Battery L36880-N4001-A100 2. Optional Battery L36880-N4001-A101 3. Standard Charger L36280-Z4-CXXX (Country Variant) 4. Travel Charger L36880-N4001-A103 (EU) / A104 (UK) Similar to standard charger with an universal input voltage from 90 ~ 240V 4. Desk Top Charger L36880-N4001-A102 5.

  • Page 13: General Information

    General Information Due to different requirements of the markets, the C35 series has different variants, which broadly classified under International version and Asian version. Marketing name for international version is C35 or C35i, whereas Asian version is named 3508 or 3508i.
  • Page 14 2. Wirelss Session Protocol Link the WAE to two session services – one connection oriented operating above the WTP and a connectionless service operating above WDP. 3. Wireless Transaction Protocol Runs on top of the datagram service and part of the standard suite of TCP/IP protocols, to provide a simplified protocol suitable for low bandwidth mobile station.

  • Page 15: C35 Series Exploded Diagram

    C35 Series Mechanical Diagram FIGURE 2.1 C35 MECHANICAL DIAGRAM. Please take note that the number(s) used here IS NOT the part number, DO NOT used it in your spare parts purchase order. A l w a y s r e f e r t o t h e S E R V I C E P A R T P R I C E L I S T f o r y o u r s p a r e p a r t o r d e r .

  • Page 16: Mechanical Concept

    Molex and Lumberg connector will be available. See photos in Additional Tools of Chapter 3 . C35 series antenna is of a snap-in type which inserted into the lower case shell (1030). The antenna can only be changed by opening up the C35 phone.

  • Page 17: Hardware Concept - Block Diagram

    Hardware Concept – Block Diagram FIGURE 2.2 C35 BLOCK DIAGRAM. V1.0...

  • Page 18: Hardware Description

    Hardware Description The handset consists of the following major integrated circuits: 1) E-GOLD – PMB2851E This IC is a combination of microprocessor, signal processor and real-time clock. The microprocessor part of this component is responsible for controlling the keyboard, SIM- Card, Flash and RAM.
  • Page 19 4) Power Supply ASIC – D0767BA This circuit provides the following main functions: • Control of switch on of the Mobile phone by ON/OFF button, Ext Power (Charger) or real time clock. • Watchdog monitor – switch off the mobile phone if no proper Watchdog signal send from HiGOLD IC.

  • Page 20: Power Supply Concept

    Power Supply Concept The C35 has two main power inputs: 1. Battery voltage(3.6V) connected at the battery contact 2. Charging voltage(6.5V) delivered by the different charger type(see Accessory List) via the Lumberg connector at the bottom of the telephone. Since the battery voltage is supplying the power supply ASIC, it is always needed to operate the phone.

  • Page 21: Battery

    1A. Battery C35 series uses a Nickel Metal Hyride (NiMH) 500mAH battery pack as standard battery. It also support the Lithium Ion 600mAH battery pack (For S35i phone) as optional battery for customer want longer talk time.

  • Page 22: Deep Discharge Battery

    1. Rapid charger 2. Travel charger 3. Car charger 4. Desktop charger PHOTO 2.33 INSERT CHARGER Photo 2.33 shows the correct way of inserting and removing the charger plug. Deep Discharge Battery In case of a deeply discharged battery, the voltage of the battery is too low to operate the charging circuit and the display controller, the phone can not be turned on and the normal charging process can not be started.
  • Page 23 The charging symbol will come up as an indication that the normal charging process has been started by the mobile. Mobile Phone C35 Spare Parts Level 2 Battery Cover L36158-A33-B..Battery NI-MH L36145-K1310-X125 Lower Case Shell L36880-A33-B..Antenna L36158-A33-B161 Vibra-Alert Unit SIM Card Reader L36453-Z5-C77 with...

  • Page 24: Disassemble The C35

    Disassemble the C35 A case opener is needed to disengage the latch of the C35 casing. PHOTO 2.3 C35 CASE OPENER The part number for this mandatory tool is F30032-P46-A1 Refer to ANNEX B of Chapter 3 for Service Equipment List. STEP 1: Remove the battery cover then the battery as shown in PHOTO 2.4 PHOTO 2.4 DISASSEMBLE C35 –...
  • Page 25 STEP 2: Open the housing with the opening tool and carefully pull the lower housing section off as illustrated in PHOTO 2.5 PHOTO 2.5 DISASSEMBLE C35 – STEP 4 STEP 3: Use the Case Opener carefully disengaged the catches of the Lower housing and Upper housing to separate the housing and the Control Board Assembly as in PHOTO 2.6 PHOTO 2.6 DISASSEMBLE C35 –...

  • Page 26: Disassemble/Assemble Lower Housing

    Disassemble/Assemble of the Lower Housing Assembly STEP 1: Open the housing with the opening tool and carefully pull the lower housing section off as illustrated in PHOTO 2.7 PHOTO 2.7 Lower Housing Assy – STEP 1 STEP 2: Remove in sequence by hand the SIM Card Holder, SIM Card Reader, Battery Contact Spring, Vibra-Alert Unit and the Antenna as illustrated in PHOTO 2.8 PHOTO 2.8 Disassembly Lower Housing –...

  • Page 27: Disassemble/Assemble Control Board Assy

    Disassemble/Assemble the Control Board Assembly STEP 1: Open the housing with the opening tool and carefully pull the lower housing section off as illustrated in PHOTO 2.9 PHOTO 2.9 Control Board Assy – STEP 1 STEP 2: Unlock the catches of the Display Module from the Control Board and move the display module to the lower part of the PCB.
  • Page 28 STEP 3: Remove the Display Module and the Buzzer Sealing from the Control Board as illustrated in PHOTO 2.11 PHOTO 2.11 Disassemble Control Board Assy – STEP 2 For Remove/Install the display module, watch out for the catches on the display module and the guide hole of the PCB.

  • Page 29: Disassemble/Assemble Upper Housing

    Disassemble/Assemble of the Upper Housing Assembly STEP 1: Open the housing with the opening tool and carefully pull the lower housing section off as illustrated in PHOTO 2.12 PHOTO 2.12 Upper Housing Assy – STEP 1 STEP 2: Remove the Keypad by hand and use a fine point metal tweezers to remove the microphone as illustrated in PHOTO 2.13 PHOTO 2.13 Disassemble Upper Housing –...

  • Page 30: Assemble The C35

    Assemble the C35 STEP 1: Check that the Lower Housing Assembly, Control Board Assembly and Upper Housing Assembly are in good order. Check if the Buzzer sealing was installed on the Control Board. N e w U p p e r a n d L o w e r C a s i n g m u s t b e u s e d . A l l c o n t a c t p i n s m u s t n o t b e d i r t y , d a m a g e d o r b e n t ! I f a n y p a r t i s n o t O .
  • Page 31 STEP 3: Close the device by putting on the Upper casing section as illustrated in PHOTO 2.16. Hold the phone and use both hands to close the casing starting from the catches at the top part near the antenna, watch out for leaving any finger marking on the display screen. n o t p l a c e t h e...

  • Page 32: Mobile Software Programming

    1. Software update to actual version and appropriate language group 2. Programming of CUSTOMER SPECIFIC INITIALIZATION Mobile Software Updating The software of the mobile, C35 series, is loaded from a PC directly. Hardware interconnection between the mobile and the PC is shown in Figure 2.6 RS232 Port...
  • Page 33 If you use the C35 battery dummy, then make sure that the power supply voltage is correctly adjusted 4.0V & 3A current rating. Description Part No. Adaptor-Cable-Bootadaptor, C35/C35 V30146-A5004-D Boot Adaptor L24857-F1006-A30 IBM Compatible PC – Pentium TABLE 2.1 EQUIPMENT LIST FOR SOFTWARE PROGRAMMING. V1.0...

  • Page 34: Language Groups

    SOFTWARE IS A DOS-BASED PROGRAM, IT IS ADVISABLE TO DO THE SOFTWARE UPGRADE IN DOS ENVIRONMENT. Languague Groups There are over 20 languages for the C35i series in total. These languages are divided into groups as follows C35i / 3508i Group Languages English, German, French, Italian, Dutch, Swedish,...
  • Page 35 This executable file needs a definition or init file, named SWUP.INI, to define the message language preferences and the hardware communication port set up. The content of this file consists of the following text: Language=English COM=x Where x is the number that corresponds to the serial port that is used, either 1, 2 or 3. Flow chart 2.1 illustrates the software programming process.

  • Page 36: Customer Specific Initialization

    C35 series IMEI label is accessible by removing the battery. It is illustrated in Photo 2.18. PHOTO 2.18 C35 SERIES IIMEI LABEL Re-use of IMEI label is possible by using a hair-dryer to remove the IMEI label.

  • Page 37: Phone Unblocking

    * # 0 0 0 3 * - - - - - - - - # The Master Phone Code can be obtained by: 1. Fax to Siemens Hotline in Germany Siemens AG ICP CD SH World Service Center, Bocholt, Germany +49-2871-91-3007 2.
  • Page 38 PHOTO 2.19 INTERNET PAGE PHOTO 2.20 INTERNET PAGE: MASTER PHONE CODE Contact your Service Manager for more information regarding setting up of the INTERNET SOLUTION & its installation procedure, ASC/T002/98. V1.0...

  • Page 39: Siemens Service Equipment

    2. Set which pass the test will be good enough to return to customer. Starting from the P35 Series, Siemens will introduce a simpler and faster testing platform for testing a repaired Siemens mobile phone. The testing platform are either base on R&S CMD 53/55 or CTS55 GSM test set.
  • Page 40 R&S CMD55 Test Station R&S CTS55 Test Station V1.0...

  • Page 41: Other Equipment

    Wavetek 4201S Test Station Other equipment One Pentium MMX Window 95/98 PC with a serial port to connect to the GSM test set through the PC serial cable provided for the GSM test set. One Test SIM card and a fully charged battery for used with the mobile phone model. Additional RF connector will be needed for setup using Wavetek 4107 test set and Wavetek Antenna Coupler.

  • Page 42: Software Installation

    Software Installation Before executing the test software, it is important to ensure that the software configuration matches that of the hardware set up. Each GSM Tester will have a specific test software. The test software are name CMD_GO, CTS_GO and for Wavetek test set, CAT4200 respectively. First, copy the installation software for the specific GSM tester to a temporary directory on the harddisk of the Window PC and then Run the Setup from the first sub directory –...

  • Page 43: Configuring The Test Software

    Configuring the test software For each model of the P35 series mobile phone, Siemens will distribute the testing configuration file for the specific test station. For testing the phone, just go to the File menu and select Load Configuration. V1.0...

  • Page 44: Running The Test Sequence

    Service Info SB_0500 for the CTS/CMD Hardware Options. Insert a Test SIM card and a fully charged battery into the Siemens mobile phone and place it onto the phone holder on the Antenna Coupler. Switch the RF switch to INT ANT position and select the Start button to run the test sequence in the configuration file.
  • Page 45 Next, the GSM test set will initial a call to the mobile phone through the Antenna Coupler. Press the Call key when the mobile phone ring, and the GSM test set will start Tx Power measurements on the GSM and GSM1800 channel specified by the configuration setting. Next, the GSM test set will end the call to the mobile phone and the screen will prompt for Dialing from the mobile phone.
  • Page 46 The GSM test set will make Tx Power measurements, Rx BER measurement, Echo Loop test on the GSM and GSM1800 channel specified by the configuration setting. There will be 2 Echo Loop Back test for checking the speech quality – one for GSM and one for GSM1800. Speak into the mobile phone when prompted and listen the voice after appr.
  • Page 47 A measurement report screen will show up and a hardcopy can be printed if a printer is connected to the PC. To close the measurement report screen, click the third button from the left. Once the mobile phone pass all the test steps, please make a check for all the key and the display.

  • Page 48: Annex A

    ANNEX A Cable Specifications 1. PC to NGSM(Power Supply) Depending on the type of serial connector that is used by the PC. The cable layout for both 9pins and 25pin are listed below: Computer: NGSM: Sub-D 25 pins Sub-D 25 pins Pin 2 Pin 3 Pin 3...
  • Page 49 Computer: CMD / CTS: Sub-D 9 pins Sub-D 9 pins Pin 3 Pin 2 Pin 2 Pin 3 Pin 6 Pin 4 Pin 5 Pin 5 Pin 4 Pin 6 Pin 8 Pin 7 Pin 7 Pin 8 TABLE A.4 D9 TO D9 CONNECTION 3.
  • Page 50 Internal dip switches of the power supply, NGSM 32/10, must be set correctly to ensure proper communication between PC and the NGSM. These switches are set up by Siemens and tested before delivery, hence it is not necessary to change it normally.

  • Page 51: Annex B

    ANNEX B Service Equipment List All purchases of jigs, tools and test equipment must be order directly from Siemens Germany. Attach the standard form with your purchase order and send it to ICP CD SL and ICP CD ST. Pos.

  • Page 52: Introduction

    Chapter /HYHO  5HSDLU 'RFXPHQW Introduction The C/M/S35 product family consists of 5 different dualband handsets (GSM-900 and GSM- 1800), which can easily be distinguished from the second block of the part number printed on the IMEI label. There also exist Asian variants of C/M/S35 named 3508 / 3518 / 3568 respectively.
  • Page 53 Tel.: +49 2842 95 4666 Fax: +49 2842 95 4302 e-mail: dominik.schnoor@klf.siemens.de This manual is intended to help you carry out repair on Level 2.5, i.e. limited component repair. Failure highlighted in this document should be repaired in the local workshop.
  • Page 54 39033, 4330.947 Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3ANC Fault Description Fault Symptoms for customers: Network Search when using the external antenna (carkit) No location update possible on external antenna (carkit) Fault Symptom on GSM-Tester: Output power problems on the external antenna No location update possible...

  • Page 55: Antenna Connector

    3ULRULW\ ‡ ..Mandatory ‡ ..Repair ‡ ..Optional ..Not Yet Defined Repair Documentation Description of procedure: D I AG N O S I S Check the output power of the handset with the LSO testprogram. Especially watch the external antenna power! R E P AI R B Y C O M P O N E N T C H AN G E Use hot air blower to remove defective connector Avoid excessive heat!
  • Page 56 J I G S AN D T O O L S Hot Air Blower Soldering Iron S P E C I AL T O O L S None W O R K I N G M AT E R I AL S Desolder Wick / Braid Solder 'UDZLQJV...
  • Page 57 5LQJHU Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3RIN Fault Description Fault Symptoms for customers: Problems with the handset ringer. No ringer tone audible. Fault Symptom on GSM-Tester: Handset fails ringer test.

  • Page 58: Ringer

    Repair Documentation Description of procedure: D I AG N O S I S Visually check the ringer. Watch for physical damage or dry joints. R E P AI R B Y C O M P O N E N T C H AN G E Resolder dry soldering joints.
  • Page 59 S P E C I AL T O O L S None W O R K I N G M AT E R I AL S Desolder Wick / Braid Solder Flux Drawings Figure 1: X35 Board Ringer Side Figure 2: X35 Ringer (B800) Placement (Top View) V1.0...

  • Page 60: Bottom Connector (Lumberg)

    %RWWRP &RQQHFWRU /XPEHUJ Affected Units Type: C/M/S35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LUC Fault Description Fault Symptoms for customers: Charging problems. Problems with external loudspeaker or microphone when using a car kit. Problems with accessories connected at the bottom connector.
  • Page 61 Repair Documentation Description of procedure D I AG N O S I S Visually check the bottom connector. Watch for dry joints! R E P AI R B Y C O M P O N E N T C H AN G E Use hot air blower remove defective bottom connector.
  • Page 62 W O R K I N G M AT E R I AL S Desolder Wick / Braid Solder Drawings Figure 1: X35 Board Bottom Connector Side Figure 2: X35 Bottom Connector Placement (Top View) Pin 12 Pin 1 Table 1: X35 Bottom Connector Pin Description V1.0...
  • Page 63 Name IN/OUT Notes Charger coding and charger control. POWER Charging Current FBatt+ Power supply for the accessories. Serial interface Serial interface ZUB_CLK Clock line for accessory bus Use as DTC In data operation ZUB_DATA I/O Data line for accessory bus. Use as CTS in data operation GND_MIC...
  • Page 64 'LVSOD\ &RQQHFWRU Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3DIC Fault Description Fault Symptoms for customers: Display problems, like missing lines or columns on the LCD or display contrast problems. Fault Symptom on GSM-Tester: Display test fails.
  • Page 65 Repair Documentation Description of procedure: D I AG N O S I S Visually check the status of the display connector. Watch for oxidation and dry solder joints. Mechanically check the opening / closing mechanism. R E P AI R B Y C O M P O N E N T C H AN G E Use hot air to remove defective connector Avoid excessive heat! Watch surrounding components!!

  • Page 66: Display Connector

    List of needed material C O M P O N E N T S D I S P L AY C O N N E C T O R Part-Number: L36195-Z26-C629 J I G S AN D T O O L S Soldering Iron Hot Air Blower S P E C I AL T O O L S...
  • Page 67 Drawings Figure 1: X35 board display connector side Figure 2: X35 display connector placement (Top View) V1.0...

  • Page 68: Keyboard Led

    .H\ERDUG /('V Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LED Fault Description Fault Symptoms for customers: Keyboard Illumination not working. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester Priority: ‡...
  • Page 69 Repair Documentation Description of procedure: D I AG N O S I S Use the diode test function of a multimeter to check the status of the diode. The typical voltage drop on the diode is 1.7V when testing the diode function with the multimeter.
  • Page 70 S P E C I AL T O O L S None W O R K I N G M AT E R I AL S Desolder Wick / Braid Solder Drawings Figure 1: X35 board keyboard LED Side Figure 2: X35 keyboard LED placement and polarity (top view) V1.0...
  • Page 71 'LVSOD\ /('V Affected Units Type: C/M/S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3LED Fault Description Fault Symptoms for customers: Display Illumination not working. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester Priority: ‡...

  • Page 72: Display Led

    Repair Documentation Description of procedure: D I AG N O S I S Use the diode test function of a multimeter to check the status of the diode. The typical voltage drop on the diode is 1.7V when testing the diode function with the multimeter.
  • Page 73 S P E C I AL T O O L S None W O R K I N G M AT E R I AL S Desolder Wick / Braid Solder Drawings Figure 1: C/M35 board display LED Side Figure 2: C/M35 board display LED placement and polarity V1.0...
  • Page 74 Figure 3: S35 board display LED side Figure 4: S35 board display LED placement and polarity V1.0...

  • Page 75: Infrared Diodes

    ,QIUDUHG 'LRGHV Affected Units Type: S 35 Affected IMEIs / Date Codes: All / All Affected SW-Versions: Fault Code for LSO reporting: 3INF Fault Description Fault Symptoms for customers: No infrared connection possible. Fault Symptom on GSM-Tester: This fault cannot be detected with a GSM-Tester. Priority: ‡...
  • Page 76 Repair Documentation Description of procedure: D I AG N O S I S Visually check the status of the IrDa module. Watch for dry solder joints. Use a reference infrared port (eg. from a notebook) to check the IrDa function. If the notebook recognizes the S35, the infrared function is ok. R E P AI R B Y C O M P O N E N T C H AN G E Use hot air to remove defective infrared module.
  • Page 77 List of needed material C O M P O N E N T S I N F R A R E D M O D U L E S 3 5 Part-Number: L36810-U6030-D670 J I G S AN D T O O L S Soldering Iron Hot Air Blower S P E C I AL T O O L S...

  • Page 78: Annex C

    ANNEX C PC Adaptor Cable & Accessories C35 Adapter Cable E-Box-PC L36880-N3101-A112 Adapter Cable PC-Mobilephone L36880-N3101-A102 Belt Clip L36880-N4001-A113 VDA Adaptercable L36880-N4001-A121 Car Kit Portable Handsfree Set L36880-N3015-A117 12 V Headset Car Kit Portable Handsfree Microphone L36880-N4001-A123 L36254-Z6-C75 Microphone Accessories Kit Car Charger Cable 10,8-24V Car Holder L36158-A98-C6...

  • Page 80: Power Plug For C35

    Power Plug for C35, M35 , S35 L36280-Z4-C321 L36280-Z4-C324 L36280-Z4-C325 L36280-Z4-C323 L36280-Z4- C322 Power Plug Travel Charger 90-240 V Travel Charger 90-240V L36880-N4001-A103 L36880-N4001-A104 Desktop Charger L36880-N4001-A102...

  • Page 81: Car Installation Kit Handfree Kit

    Car installation kit Ratio unit C35, M35 & S35 Cradle Comfort L36158-A37-B1 Handset L36880-N3015-A123 Connection Box Ratio Handsfree Microphone L36880-N4001-A116 Con. Cable Battery Comfort L36146-A2053-D Phone In Adapter L36880-N3015-A137 1RW LQFOXGHG LQ RXU 6WDQGDUG 'HOOLYU\...

  • Page 82: Car Installation Kit Handfree Pro

    Car installation kit hands free unit C35, M35, S35 Handsfree Loudspeaker Phone In Adaptor L36104-F3090-X902 L36880-N3015-A137 Con. Cable Battery Comfort L36146-A4013-D Fuses 3A Radio Mute black Battery Battery Ground brown Ignition violet 1,8m Connection Box L36880-S2001-A100 Handsfree Microphone L36254-Z6-C76 Cradle Comfort Handset L36158-A37-B1 L36880-N3015-A123...
  • Page 83 Carkit installation kit hand free unit Professional C35, M35, S35 Handsfree Loudspaker L36104-F3090-X901 Con. Cable Battery L36146-A1030-D Radio Mute black Lights Dimmer yellow Fuses 3A Automatic Antenna white Battery Battery ground brown 1,9m Ignition violet Handfree Microphone L36254-Z6-C63 Push to talk cable L36146 A4012 D Adapter Cable E-Box-PC...
  • Page 84 Carkit installation Comfort GPS C35, M35, S35 Handset L36880-N3015- Combi Antenna GPS A123 L36851-Z1901-A46 Crash Sensor Con. Pox L36880-N4001-A115 Connection Pox GPS L36880-S4001-A4 Car Cradle Telematic L36158-A37-B6 Antenna Handsfree Loudspeaker L36104-F3090-X902 Handsfree Microphone L36880-N4001-A116 Con. Cable Battery L36146-A2053-D Phone In Adapter L36880-N3015-A137 1RW LQFOXGHG LQ RXU 6WDQGDUG...
  • Page 85 PC Adaptar Cable & Accessory C35, M35, S35 Adaptor Cable E-Box -PC L36880-N3101-A112 Adapter Cable PC-Mobilephone L36880-N3101-A102 Belt Clip L36880-N4001-A113 VDA Adaptercable L36880-N4001-A121 Car Kit Portable Handsfree Set L36880-N3015-A117 12 V Car Kit Portable Handsfree Microphone L36254-Z6-C75 Headset L36880-N4001-A123 Car Holder Microphone Accessories Kit Car Charger cable 10, 8 –...

  • Page 86: References

    6. IrDA(Infrared Data Association), Serial Infrared Physical Layer Link Specification, Version 1.1 , October 15, 1995. Disclaimer: This content is subjected to change without notice. Copyright © 2000 Siemens Advanced Engineering Pte Ltd ICP CD Asia Service Center, 164, Kallang Way, #04-22, Kolam Ayer Industrial Estate, Singapore 349248 Author: Tan Guan San.

Table of Contents