Related Manuals for Husqvarna K950 Ring
Summary of Contents for Husqvarna K950 Ring
- Page 1 Oper ator ′ s manual K950 Ring Please r ead the operator’s manual carefully and make sure you understand the E E E E n n n n g g g g l l l l i i i i s s s s h h h h...
-
Page 2: Key To Symbols
KEY TO SYMBOLS Key to symbols Stop, with the return spring to the operating position. WARNING! The machine can be a dangerous tool if used incorrectly or carelessly, which can cause serious or fatal injury to the operator or others. Stop, in the fixed position. -
Page 3: Table Of Contents
CONTENTS Contents KEY TO SYMBOLS Key to symbols ............. CONTENTS Contents ..............WHAT IS WHAT? What is what on the power cutter? ....... SAFETY INSTRUCTIONS Steps before using a new power cutter......Personal protective equipment ........Machine′s safety equipment ........Checking, maintaining and servicing the machine′s safety equipment ............ -
Page 4: What Is What
WHAT IS WHAT? 29 30 What is what on the power cutter? 1 Control for the guide rollers 18 Water adjustment control 2 Grease nipples 19 Warning decal 3 Blade guard/spray guard 20 Choke 4 Water connector 21 Start throttle lock 5 Locking button for the drive wheel 22 Stop switch 6 Diamond blade... -
Page 5: Safety Instructions
• Protective goggles or a visor • Let your Husqvarna dealer regularly check the power cutter and make essential adjustments and repairs. WARNING! Under no circumstances may the design of the machine be modified without •... -
Page 6: Machine's Safety Equipment
SAFETY INSTRUCTIONS Machine′s safety equipment IMPORTANT INFORMATION This section describes the machine′s safety equipment, its For mufflers it is very important that you follow the purpose, and how checks and maintenance should be carried instructions on checking, maintaining and servicing your out to ensure that it operates correctly. -
Page 7: Checking, Maintaining And Servicing The Machine's Safety Equipment
SAFETY INSTRUCTIONS Checking, maintaining and servicing Regularly check that the muffler is securely attached to the machine. the machine′s safety equipment WARNING! All servicing and repair work on the machine requires special training. This is especially true of the machine′s safety equipment. -
Page 8: General Safety Precautions
A damaged blade can cause personal injuries. See instructions under the heading Assembly. General safety precautions IMPORTANT INFORMATION K950 Ring may only be used for wet cutting. The water cleans and cools both the blade • Never start the machine: and the component parts of the cutting equipment. -
Page 9: General Working Instructions
SAFETY INSTRUCTIONS General working instructions Cutting WARNING! The safety distance for the power WARNING! This section describes basic cutter is 15 metres. You are responsible to safety directions for using a power cutter. ensure that animals and onlookers are not This information is never a substitute for within the working area. - Page 10 Cutting depth How to avoid kickback K950 Ring can cut up to a depth of 260 mm (10 inches). Making a guide cut of 50-70 mm (2-3 inches) first, gives you better control of the machine. This means the water disc can WARNING! Kickback can happen very penetrate into the workpiece and help control the machine.
-
Page 11: Diamond Blades
SAFETY INSTRUCTIONS Diamond blades General rules • Never start to cut with the upper quadrant of the blade as Diamond blades consist of a steel body provided with shown in the figure, also known as the kickback zone. segments that contain industrial diamonds. Always use a sharp diamond blade. -
Page 12: Settings And Adjustments
We offers a number of blades for different materials in its is not transferred at the centre of the blade. The flanges on the range. Check with your Husqvarna dealer to see which blades two guide rollers run in the blade’s groove. Springs on the are best suited for your usage. - Page 13 SETTINGS AND ADJUSTMENTS • Fit the blade. • Adjust so you can easily stop the support rollers using your thumb when the blade is rotated. The support rollers CAUTION! The blade has a groove (A) on one side that should only follow the blade occasionally. acts a the guide groove for the support rollers.
-
Page 14: Dismantling The Complete Guide Roller
SETTINGS AND ADJUSTMENTS Dismantling the complete guide Assembling the complete guide roller roller • Remove the support roller cover. • Screw the knob until it bottoms, and then loosen the knob 2 turns. • Lift off the blade. • Insert the guide roller in the chassis •... -
Page 15: Important Notes
SETTINGS AND ADJUSTMENTS Important notes: • Replace the guide rollers when half of the flange on the rollers is worn. • Incorrect adjustment can result in damage to the blade. A) New • If the blade rotates slowly or stops, stop cutting B) Worn immediately and trouble shoot. -
Page 16: Fuel Handling
When refuelling, open the fuel cap slowly so that any excess pressure is released gently. • For best results and performance use HUSQVARNA two- Tighten the fuel cap carefully after refuelling. stroke engine oil, which is specially formulated for our air- cooled two-stroke engines. -
Page 17: Starting And Stopping
STARTING AND STOPPING Starting and stopping Starting WARNING! The cutting blade rotates when WARNING! Note the following before the engine is started. Make sure it can rotate starting: freely. Do not start the power cutter without the belt Grip the front handle with your left hand. Put your right foot on guard fitted. -
Page 18: Maintenance
Now tighten the screw holding the belt tensioner. Never start the engine when the belt pulley and clutch are removed for maintenance. Carburettor Your Husqvarna product has been designed and manufactured to specifications that reduce harmful emissions. The carburettor is equipped with fixed needles to ensure the machine always receives the correct mixture of fuel and air. -
Page 19: Fuel Filter
In order to obtain a good filtering effect, the filter must be replaced regularly or cleaned and oiled. A special HUSQVARNA oil has been produced for this purpose. Rec. idle speed 2500 rpm Remove the foam plastic filter. Wash the filter well in tepid soapy water. -
Page 20: Starter
MAINTENANCE Starter Guide the cord through the cut-out in the periphery of the pulley and wind the cord 3 times clockwise around the centre of the starter pulley. WARNING! When the recoil spring is wound up in the starter housing it is under tension and can, if handled carelessly, pop out and cause personal injury. -
Page 21: Spark Plug
MAINTENANCE • Loosen the bolts holding the spring cassette. • If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking any further action. If the spark plug is dirty, clean it and check that the electrode gap is 0.5 mm. -
Page 22: Muffler
A shattered blade can cause serious personal injuries to the user or other persons. For this reason Husqvarna does not approve ring cutting blades that have been reconstructed. Contact your Husqvarna dealer for instructions. -
Page 23: General Maintenance Instructions
MAINTENANCE General maintenance instructions Below you will find some general maintenance instructions. If you have more questions, contact your service agent. Daily maintenance 1 Lubricate the guide rollers. 2 Check that the components of the throttle control work smoothly (throttle control and throttle trigger lock). 3 Check the guide rollers for wear when replacing the blade. -
Page 24: Technical Data
TECHNICAL DATA Technical data Engine K950 Ring Cylinder displacement, cm 93,6 Cylinder bore, mm Stroke, mm 38,0 Idle speed, rpm 2500 Recommended max. fast idle speed, rpm 9750±250 Power, kW/ rpm Ignition system Type of ignition system Spark plug NGK BPMR 7A... -
Page 25: Trouble Shooting
TECHNICAL DATA Trouble shooting Mechanics Symptom Probable cause 1 Roller knobs not tightened fully. The blade does not rotate. 2 The blade not fitted on guide rollers correctly. 3 Rollers tensioned too much. 1 Roller knobs not tightened fully. 2 Worn drive wheel. The blade rotates too slowly. -
Page 26: Ec-Declaration Of Conformity
Husqvarna Construction Products, SE-433 81 Partille, Sweden, tel: +46-31-949000, declares under sole responsibility that the power cutter K950 Ring from year 2006 serial numbers and onward (the year is clearly stated in plain text on the rating plate with subsequent serial number) conforms with the requirements of the COUNCIL’S DIRECTIVE: •... - Page 28 1150289-26 ´®z+R<|¶69¨ ´®z+R<|¶69¨ 2006-12-09...