Table of Contents
Advertisement
Quick Links
Models/Modelos
721.85062
721.85063
721.85064
721.85069
Read and save these
installation
instructions,
Lea y guarde
estas
instrucciones
de
instalaci6n
iNSTALLATiON
iNSTRUCCIONES
iNSTRUCTiONS
!
DE INSTALACION
i
i
Microwave Hood Combination
Combinaci6n M icroondas C ampana
Part No. MFL39433003
Sears, Roebuck and Co., Hoffman Estates,IL 60179
www.sears.com
Advertisement
Table of Contents
Related Manuals for Kenmore 721.85062
Summary of Contents for Kenmore 721.85062
- Page 1 Models/Modelos iNSTRUCCIONES DE INSTALACION 721.85062 721.85063 721.85064 721.85069 Microwave Hood Combination Read and save these installation instructions, Combinaci6n M icroondas C ampana Lea y guarde estas instrucciones instalaci6n Part No. MFL39433003 Sears, Roebuck and Co., Hoffman Estates,IL 60179...
-
Page 2: Your Safety First
YOUR SAFETY FIRST BEFORE YOU START * Proper installation is the instailer's responsibility! - Read the entire manual before you begin. - The model number label is located on the oven front of oven behind doon See Figure 1. - Mounting plate is located on back side of microwave oven. See Figure 2. BE SURE TO READ THE FOLLOWING SAFETY iNSTRUCTiONS: Model... - Page 3 YOUR SAFETY FIRST • THIS APPLIANCE MUST BE GROUNDED! - if there is an electrical short circuit, grounding reduces the risk of electrical shock by providing escape wire for the electric current. This appliance is equipped with a cord having a grounding wire with a grounding plug.
- Page 4 YOUR SAFETY FIRST • MAKE SURE YOU HAVE ENOUGH SPACE AND SUPPORT. - Mount the oven against a flat, vertical wail, so that it is supported by the wail. The wall should be constructed of minimum 2" x 4" wood studding and 3/8"...
-
Page 5: Parts, Tools, Materials
PARTS, TOOLS, MATERIALS THE FOLLOWING PARTS ARE SUPPLIED WiTH THE OVEN: NOTE: Depending on your ventilation requirements, you may not use all of these parts. Damper/duct connector One power cord clamp (for roof vented or wall vented installation). One dark-colored mounting screw (to hold the power cord). - Page 6 PARTS, TOOLS, MATERIALS YOU WILL NEED THE FOLLOWING TOOLS AND MATERIALS FOR THE INSTALLATION: Carton or other heavy material for covering the counter top. Clear tape Stud finder (for taping the templates to the wail). Saber Keyhole saw (for the power cord hole). (for cutting vent holes for roof or wail venting).
-
Page 7: Step7: Prepare Theelectrical Connections
STEP7: PREPARE THEELECTRICAL CONNECTIONS WARNING AVOID ELECTRICAL SHOCK! THiS APPLIANCE MUST BE GROUNDED! 1. Locate the grounded electric outlet for this oven in the cabinet above the oven, as shown in Figure 5. NOTE: The outlet should be on a circuit dedicated to the Upper Cabinet microwave... -
Page 8: Step2 : Prepare Theventing System
STEP2 : PREPARE THEVENtiNG SYSTEM NOTE: The ductwork you need for outside ventilation is not included with your oven. The standard ductwork fittings and length are shown in Figure 10, page 9. WARNING j THIS OVEN MUST BE PROPERLY VENTED! You may vent your oven in one of three ways. - Page 9 STEP2 : PREPARE THE VENTING SYSTEM STANDARD FiTTiNGS NOTE: If the existing duct is round, you must use a rectangular-to-round adapter, with a rectangular 3" extension duct installed between the damper assembly and the adapter to prevent the exhaust damper sticking.
-
Page 10: Step3 : Prepare Theventing Blower
STEP3 : PREPARE THEVENtiNG BLOWER WARNING * To avoid risk of property damage, unplug the microwave oven or disconnect power at source by removing fuse or throwing circuit breaker. " To avoid risk of personal injury, wear protective gloves when handling mounting plate. DO NOT PULL OR STRETCH THE BLOWER WIRING! Pulling and stretching the blower... - Page 11 STEP3 : PREPARE THEVENtiNG BLOWER 4. Reassemble the blower wire. See Figure 15. 5. Rotate the unit so that the exhaust ports face the rear of the cabinet. See Figure ] 7. When you insert blower unit, blower wire must be like Figure 16. 6.
-
Page 12: Step 4: Prepare The Wall And Upper Cabinet For Installation
STEP 4: PREPARE THE WALL AND UPPER CABINET FOR INSTALLATION WARNING To avoid personal injury or property damage, do not attempt to install this microwave oven if you cannot find a wail stud. MEASURE AND TACK / TAPE UP THETEMPLATE 1. - Page 13 STEP 4: PREPARE THE WALL A ND UPPER CABINET FOR INSTALLATION WARNING To avoid risk of personal injury, electrical shock or death: • Note where electrical outlets and electrical wires are before drillinto the wall. • Locate disconnect power to any electrical circuits that could be affected...
- Page 14 STEP 5" INSTALL THE MOUNTING PLATE TO THEWALL THE OVEN MUST BE CONNECTED 3/1 6" Hole on Studs AT LEAST ONE WALL STUD 3/4" Hole on Dry wall Only 1. Draw a vertical line on the wall at the center of the 66"I I Minimum IFrom theFIoorl...
- Page 15 STEP 5 : INSTALL THE MOUNTING PLATE TO THEWALL FOR WALL-VENTING * Make the box cutout for the rear wall duct. - 1 piece mounting plate: Using a pencil, put dots through slots F and G, and through holes H and [. Remove the mounting plate and draw lines extending through...
-
Page 16: Step 6 :Attachtheoven To Thewall
STEP 6 :ATTACHTHEOVEN TO THEWALL WARNING To avoid risk of personal injury or property damage, use will need people install this microwave oven. 1. Carefully lift microwave oven and hang it on support tabs (See Figure 28) at the bottom of the Power cord mounting... - Page 17 STEP 6 :ATTACHTHEOVEN TO THEWALL 5. Roof vented installation: See Figure 34. Daipo r Install ductwork through the vent opening in the upper cabinet. Complete the venting system through the roof according to the method needed. See _°PREPARE THE VENTING SYSTEM"...
- Page 18 MEMO...
- Page 19 MEMO...
- Page 20 Impreso en China...