Page 1: And Controls
4RUNNER (1998) Part 1 Ignition switch with steering lock OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 6 Ignition switch, Transmission and Parking brake Ignition switch with steering lock Automatic transmission Manual transmission Four- wheel drive system _ Rear differential look system Parking brake Cruise control Clutch start cancel switch...
Page 2 4RUNNER (1998) ”START”—Starter motor on. The key CAUTION will return to the ”ON” position Vehicles with manual transmission— when released. You must push in the key to turn the For manual transmission: For starting tips, see Part 3. key from ”ACC” to the ”LOCK” posi- Never remove the key when the tion.
Page 3 4RUNNER (1998) Automatic transmission "Two- wheel drive models Overdrive switch Lock release button For selecting either a three-speed or four-speed To prevent misshifting transmission Parking, engine starting and key removal position Reverse position ”ON” position ”O/D OFF” indicator ”OFF” position Neutral position (Shifting into light shows the over-...
Page 4 4RUNNER (1998) CAUTION Your automatic transmission has a 3. Release parking brake shift lock system to minimize the pos- brake pedal. Depress the accelera- Never put your foot on the accel- sibility incorrect operation. This tor pedal slowly for smooth start- erator pedal while shifting.
Page 5 4RUNNER (1998) 5VZ- FE engine..58 km/h (36 mph) Vehicles with cruise control When the NOTICE cruise control is being used, even if downshift transmission by z Be careful not to overrev the turning off the overdrive switch, en- engine. Watch the tachometer to gine braking is not applied because keep engine rpm from going the cruise control is not cancelled.
Page 6 4RUNNER (1998) (f) Good driving practice (g) Rocking your vehicle if stuck NOTICE If the transmission is repeatedly CAUTION Never shift into reverse while the upshifted and downshifted between vehicle is moving. third gear overdrive when To rock your vehicle if it becomes climbing a gentle slope, the over- stuck in snow, mud, sand, etc., (e) Parking...
Page 7 To set the ”PWR” mode, push in the driving pat- tern selector button. The ”PWR” mode indicator light comes on. For ordinary driving, Toyota recom- mends using the ”NORM” mode to im- prove fuel economy. (i) If you cannot shift the selector lever out of ”P”...
Page 8 4RUNNER (1998) Automatic transmission "Four- wheel drive control Overdrive switch Lock release button To prevent misshifting For selecting either a three-speed or four-speed transmission Parking, engine starting and key removal position Reverse position ”ON” position ”O/D OFF” indicator ”OFF” position Neutral position (Shifting into light shows the over-...
Page 9 4RUNNER (1998) Your automatic transmission has a Always turn the overdrive switch on Shift into the ”2” position. The shift lock system to minimize the pos- for better fuel economy and quieter transmission will downshift to the sibility incorrect operation. This driving.
Page 10 4RUNNER (1998) Front drive control lever in ”L4” 3RZ- FE engine..11 km/h Vehicles with cruise control When the mph) cruise control is being used, even if downshift transmission by 5VZ- FE engine..12 km/h turning off the overdrive switch, en- mph) gine braking is not applied because the cruise control is not cancelled.
Page 11 4RUNNER (1998) z Be careful not to overrev the engine. Watch the tachometer to NOTICE Do not continue hill climbing or keep engine rpm from going hard towing for a long time in into the red zone. The approxi- the ”2” or ”L” position. This mate maximum allowable speed cause severe...
Page 12 The ”PWR” objects. mode indicator light comes on. CAUTION For ordinary driving, Toyota recom- NOTICE mends using the ”NORM” mode to im- Always keep your foot on the prove fuel economy. brake pedal while stopped with If you rock your vehicle, observe the engine running.
Page 13 4RUNNER (1998) Manual transmission (i) If you cannot shift the selector lever out of ”P” position If you cannot shift the selector lever from the ”P” position even though the brake pedal is depressed, use the shift lock override lever. For instruc- tions, see ”If you cannot shift auto- matic transmission selector lever”...
Page 14 4RUNNER (1998) Upshifting gear km/h (mph) Downshift to the appropriate gear if 5VZ- FE engine 1 to 2 24 (15) acceleration is needed when you are gear km/h (mph) 2 to 3 40 (25)/58 (36) cruising below the above downshifting ”H2”...
Page 15 4RUNNER (1998) Four- wheel drive system— (a) Front drive control (lev type) Good driving practice If it is difficult to shift into reverse, put the transmission in neutral, re- lease the clutch pedal momentarily, and then try again. When towing a trailer, in order to maintain engine braking efficiency, do not use the fifth gear.
Page 16 4RUNNER (1998) (a) Front drive control (lever/button type) Use the front drive control lever to select the following transfer modes. ”N” (neutral position): Lever at ”N” ”H2” (high speed position, two- No power is delivered to the wheels. wheel drive): Lever at ”H2” The vehicle must be stopped.
Page 17 4RUNNER (1998) (b) A.D.D. (automatic disconnecting differential) Use the front drive control lever and ”4WD” button to select the fol- ”N” (neutral position): Lever at ”N” lowing transfer modes. No power is delivered to the wheels. ”H2” (high speed position, two- The vehicle must be stopped.
Page 18 4RUNNER (1998) Steel wheels Aluminum wheels You should drive in four- wheel drive for at least 16 km (10 miles) each The A.D.D. can be engaged or dis- month. This will assure that the front engaged by the shifting operations drive components are lubricated.
Page 19 4RUNNER (1998) (c) Shifting procedure (lever type with manu transmission) SHIFTING BETWEEN ”H2” AND ”H4” With A.D.D. SHIFTING BETWEEN ”H4” AND ”L4” To shift from ”H2” to ”H4”, move To shift from ”H2” to ”H4”, reduce To shift from ”H4” to ”L4, stop the the front drive control lever.
Page 20 4RUNNER (1998) (c) Shifting procedure (lev type with automat (c) Shifting procedure transmission) (lever/button type) SHIFTING BETWEEN ”H2” AND ”H4” With A.D.D. SHIFTING BETWEEN ”H2” AND ”H4” To shift from ”H2” to ”H4”, move To shift from ”H2” to ”H4”, reduce To shift from ”H2”...
Page 21 4RUNNER (1998) Rear differential lock system To shift from ”H4” to ”H2”, push the ”4WD” button again to turn it off. This can be done at any vehicle speed. If the indicator light does not go off when you shift the transfer into ”H2”, drive straight ahead while accelerating or decelerating, or drive in reverse.
Page 22 4RUNNER (1998) The rear differential lock system is provided for use only when wheel spinning occurs in a ditch or on a CAUTION slippery or ragged surface. Do not use the rear differential This differential lock system is effec- lock in the conditions other than tive in case one of the rear wheels is above.
Page 23 4RUNNER (1998) To lock the rear differential, push CAUTION the switch. The anti- lock brake system does not Be sure to stop the wheels before operate when the rear differential is Do not lock the differential until locking the differential. locked.
Page 24 4RUNNER (1998) For easy unlocking, slightly turn the Parking brake steering wheel in either direction while The differential will also unlock if you the vehicle is in motion. shift the front drive control lever out When the differential lock is disen- of ”L4”.
Page 25 4RUNNER (1998) Cruise control The cruise control allows you to CAUTION cruise vehicle desired speed over 40 km/h (25 mph) even Before driving, be sure the park- with your foot off the accelerator ing brake is fully released and pedal. the parking brake reminder light Your cruising speed can be maintained is off.
Page 26 4RUNNER (1998) TURNING ON THE SYSTEM To operate the cruise control, press the ”CRUISE ON- OFF” button. This turns the system on. The indicator light in the instrument panel shows that you can now set the vehicle at desired cruising speed.
Page 27 4RUNNER (1998) SETTING AT A DESIRED SPEED a. Pulling the lever in the ”CANCEL” direction and releasing it. On vehicles with automatic transmis- If you need acceleration—for example, b. Depressing the brake pedal. sion, the transmission must be in ”D” when passing—depress the accelera- c.
Page 28 Toyota dealer at the earliest op- gine braking will not be applied be- The indicator light does not come portunity.
Page 29 4RUNNER (1998) Clutch start cancel switch (four- wheel drive models wi manual transmission) To crank the engine without de- pressing the clutch pedal, push the Never use the switch for normal en- switch with the ignition on. gine starting. Be sure to follow the The switch stays on as long as the starting procedure instructed in ”How ignition is on.
Page 30 4RUNNER (1998)
Page 31: Instruments And Controls
4RUNNER (1998) Car audio system— —Reference Part 1 _ Rear heater system OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 7 Car audio system and Air conditioning system Car audio system Reference Using your audio system: some basics Using your audio system: controls and features Car audio system operating hints...
Page 32 4RUNNER (1998) Type 1: AM F M ETR radio/cassette play- er/compact disc auto changer controller Type 2: AM F M ETR radio/compact disc player/compact disc auto changer con- troller...
Page 33 ”ACC” or ”ON” This section describes some of the changer controller position. basic features on Toyota audio sys- TURNING THE SYSTEM ON AND tems. Some information may not per- tain to your system.
Page 34 Balance sette tape or compact disc. If the fore driving your Toyota through another function was previously play- A good balance of the left and right an automatic car wash. On ve- ing, it will come on again.
Page 35 4RUNNER (1998) —Using your audio system: controls and features "Type 1 YOUR CASSETTE PLAYER 8 cm (3 in.) compact disc singles When you insert a cassette, the ex- Your compact disc player does not posed tape should be to the right. need an adaptor to play compact disc singles.
Page 36 4RUNNER (1998) Details of specific buttons, controls, 1 2 3 4 5 6 (Preset buttons) and features are described in the al- These buttons are used to preset and phabetical listing that follows. tune in radio stations. To preset a station to a button: Tune in the desired station (see ”TUNE”...
Page 37 4RUNNER (1998) Sound balance adjustment func- (Reverse/Fast forward but- tion— Push ”AM” to switch the AM band. tons) ”AM” will appear on the display. This knob is also to adjust the sound Cassette Player balance between the front and rear, If the audio system is off, you can Push the fast forward button to fast and the right and left speakers.
Page 38 If the malfunction is not recovered, push ”CD”, the system changes be- used for recording the tape. take your vehicle to your Toyota deal- tween single disc player and automat- : Dolby noise reduction manufactured under license ic changer.
Page 39 4RUNNER (1998) RAND (Random) RPT (Repeat) Push ”FM” to switch the FM band. There are two random features—you There are two repeat features—you ”FM1” or ”FM2” will appear on the can either listen to the tracks on all can either replay a disc track or a display.
Page 40 4RUNNER (1998) SCAN Compact disc player ST (Stereo reception) display Radio There are two scan features—you can Your radio automatically changes to either scan the tracks on a specific stereo reception when a stereo broad- You can either scan all the frequen- disc or scan the first tracks of all the cast is received.
Page 41 4RUNNER (1998) "Type 2 TUNE Tuning Your Toyota has an electronic tuning radio (ETR). Push and release the ” ” (up) or ” ” (down) side of ”TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.)
Page 42 4RUNNER (1998) Details of specific buttons, controls, 1 2 3 4 5 6 (Preset buttons) and features are described in the al- These buttons are used to preset and phabetical listing that follows. tune in radio stations. To preset a station to a button: Tune in the desired station (see ”TUNE”...
Page 43 4RUNNER (1998) AUDIO CONTROL / MODE Sound balance adjustment func- (Reverse/Fast forward but- tion— Manual tone adjustment function— tons) This knob is also to adjust the sound This knob is used to adjust the tone If you want to fast forward or reverse balance between the front and rear, manually.
Page 44 If the malfunction is not recovered, tween built- in single disc player and beep, you held the button too long, take your vehicle to your Toyota deal- automatic changer. and the player will play all the tracks in the magazine in random order. To...
Page 45 4RUNNER (1998) RPT (Repeat) SCAN Compact disc player There are two repeat features—you Radio There are two scan features—you can can either replay a disc track or a either scan the tracks on a specific You can either scan all the frequen- whole compact disc.
Page 46 TUNE (Tuning) Your radio automatically changes to Tuning stereo reception when a stereo broad- Your Toyota has an electronic tuning cast is received. ”ST” appears on the radio (ETR). Push and release the ” ” display. If the signal becomes weak, (up) or ”...
Page 47 4RUNNER (1998) Details of specific buttons, controls, 1 2 3 4 5 6 (Preset buttons) and features are described in the al- These buttons are used to preset and phabetical listing that follows. tune in radio stations. To preset a station to a button: Tune in the desired station (see ”TUNE”...
Page 48 4RUNNER (1998) For high- pitch tone adjustment, push (Reverse/Fast forward but- ”AUDIO CONTROL MODE” Push ”AM” to switch the AM band. tons) repeatedly until ”TRE” appears on the ”AM” will appear on the display. Cassette Player display. Then turn the knob to suit If the audio system is off, you can your preference.
Page 49 If the malfunction is not recovered, push ”CD”, the system changes be- used for recording the tape. take your vehicle to your Toyota deal- tween single disc player and automat- : Dolby noise reduction manufactured under license ic changer.
Page 50 4RUNNER (1998) MTL (Metal) Display RAND (Random) RPT (Repeat) If a metal or chrome equivalent cas- There are two random features—you Cassette Player sette tape is put in the cassette play- can either listen to the tracks on all Push ”RPT” while the track is playing. er, the player will automatically adapt the compact discs in the magazine in ”RPT”...
Page 51 4RUNNER (1998) Compact disc auto changer only— To scan the preset stations: Compact disc auto changer only— Push and hold ”SCAN” until you hear Repeating a disc: Scanning for the first tracks of all the a beep. The radio will tune in the next Push and hold ”RPT”...
Page 52 4RUNNER (1998) Cassette Player The track number you select is not ST (Stereo reception) display valid if it is higher than the number By using this button, you can skip up Your radio automatically changes to of tracks remaining on the current or down to a different track.
Page 53 4RUNNER (1998) "Type 4 TUNE (Tuning) Your Toyota has an electronic tuning radio (ETR). Push and release the ” ” (up) or ” ” (down) side of ”TUNE” to step up or down the station band. (If you hear a beep, you held the button too long and the radio will go into the seek mode.)
Page 54 4RUNNER (1998) Details of specific buttons, controls, 1 2 3 4 5 6 (Preset buttons) and features are described in the al- These buttons are used to preset and phabetical listing that follows. tune in radio stations. To preset a station to a button: Tune in the desired station (see ”TUNE”...
Page 55 4RUNNER (1998) AM FM For high- pitch tone adjustment, push (Reverse/Fast forward but- ”AUDIO CONTROL MODE” Push ”AM FM” to switch between the tons) repeatedly until ”TRE” appears on the AM and FM bands.”AM”, ”FM1” or Cassette Player display. Then turn the knob to suit ”FM2”...
Page 56 If the malfunction is not recovered, push ”CD”, the system changes be- used for recording the tape. take your vehicle to your Toyota deal- tween built- in single disc player and : Dolby noise reduction manufactured under license automatic changer.
Page 57 4RUNNER (1998) There must be at least 3 seconds of blank space between tracks in order PROG (Program) Random playing for the tracks on a for the repeat feature to work correct- disc: Quickly push release Push ”PROG” to select the other side ”RAND”.
Page 58 4RUNNER (1998) Compact Disc Player SCAN Compact disc player There are two repeat features—you Radio There are two scan features—you can can either replay a disc track or a either scan the tracks on a specific You can either scan all the frequen- whole compact disc.
Page 59 4RUNNER (1998) SEEK (Seeking) When counting the number of tracks SKIP you want to rewind, remember Radio The skip feature allows you to fast count the current track as well. For forward past long stretches of blank In the seek mode, the radio finds and example, if you want to rewind to a tape.
Page 60 Increas- interfere with AM signals. And of Your Toyota has an electronic tuning ing the bass level may reduce static course, radio signals have a limited radio (ETR). Push and release the ” ” and fluttering.
Page 61 4RUNNER (1998) Use high- quality cassettes. Fading—AM broadcasts are reflected Low- quality cassette tapes by the upper atmosphere—especially cause many problems, including at night. These reflected signals can poor sound, inconsistent playing interfere with those received directly speed, and constant auto- revers- from the radio station, causing the ra- ing.
Page 62 4RUNNER (1998) CARING FOR YOUR COMPACT DISC Remove discs from the compact PLAYER AND DISCS disc player when you are not lis- If moisture gets into your compact tening Use only compact discs labeled as disc player, you may not hear any to them.
Page 63 4RUNNER (1998) Air conditioning system— —Controls A new disc may have rough edges on its inner and outer perimeter. Remove the rough edges by press- CAUTION ing the side of a ball- point pen or pencil against the inner and outer Compact disc players use invis- perimeter of the disc as shown.
Page 64 4RUNNER (1998) Fan speed selector Move the lever to adjust the fan speed—to the right to increase, to the left to decrease. Temperature selector Move the knob to adjust the tempera- ture—to the right to warm, to the left to cool. Air flow selector 3.
Page 65 To turn on the air conditioning, press automatically shuts off. If this hap- 1. Recirculate—Recirculates the ”A/C” button. The ”A/C” button in- pens, take your vehicle to a Toyota inside the vehicle. dicator will come on. To turn the air dealer for service.
Page 66 4RUNNER (1998) —Air flow selector settings...
Page 67 4RUNNER (1998) —Operating tips To cool off your Toyota after it has Heating Air conditioning been parked in the hot sun, drive For best results, set controls to: For best results, set controls to: with the windows open for a few minutes.
Page 68 4RUNNER (1998) —Instrument panel vents Defogging Defrosting The inside of the windshield The outside of the windshield For best results, set controls to: For best results, set controls to: speed—Any setting except speed—Any setting except ”OFF” ”OFF” Temperature—Towards Temperature—Towards WARM WARM (red zone) to heat;...
Page 69 4RUNNER (1998) Side vents Lower vent If air flow control is not satisfactory, check the instrument panel vents. The instrument panel vents may be opened or closed as shown.
Page 70 4RUNNER (1998) —Rear heater system 1. Fan Speed Selector 2. Temperature Selector Fan speed selector Push the switch toward ”HI” or ”LO”. Temperature selector Place the lever anywhere ex- cept the ”OFF” position.
Page 71 4RUNNER (1998)
Page 72 4RUNNER (1998) Part 1 Keys OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 2 Keys and Doors " Keys " Side doors " Power windows " Power back window " Back door " Hood " Fuel tank cap " Electric moon roof...
Page 73 4RUNNER (1998) Your vehicle is supplied with two kinds of key. 1. Master key—This key works in ev- ery lock. 2. Subkey—This key will not work in the glovebox. To protect things locked in the glove- when have your vehicle parked, leave the subkey with the at- tendant.
Page 74 If you should lose your keys or if you need additional keys, duplicates can be made by a Toyota dealer using the key number. You should also put a copy of the key number with your important papers.
Page 75 4RUNNER (1998) LOCKING AND UNLOCKING WITH Insert the key into the keyhole and turn it. To lock: Turn the key forward. To unlock: Turn the key backward. Vehicles with power door lock sys- tem— All the side doors and back door lock and unlock simultaneously with either front door.
Page 76 4RUNNER (1998) LOCKING AND UNLOCKING WITH INSIDE LOCK BUTTON Move the lock button. To lock: Push the button downward. To unlock: Pull the button upward. Closing the door with the lock button pushed in will also lock the door. Be careful not to lock your keys in the vehicle.
Page 77 4RUNNER (1998) Driver’s side Front passenger’s side With power window...
Page 78 4RUNNER (1998) Driver’s side Front passenger’s side Without power window To lock: Push the switch on the front side. LOCKING AND UNLOCKING WITH To unlock: Push the switch on the POWER DOOR LOCK SWITCH rear side. Push the switch.
Page 79 4RUNNER (1998) All the doors lock or unlock simulta- neously. REAR DOOR CHILD- PROTECTORS Power windows Move the lock lever to the ”LOCK” CAUTION position as shown on the label. This feature allows you to lock a rear Before driving, be sure that the door so it can be opened from the doors are closed and locked, es- outside only, not from inside.
Page 80 4RUNNER (1998) The windows can be operated with the switch on each side door. The power windows work when the ignition switch is in the ”ON” position. However, if both front side doors are closed, they work for 43 seconds even after the ignition switch is turned off.
Page 81 4RUNNER (1998) Automatic operation (to open only): Push the switch completely down and then release it. The window will fully open. To stop the window partway, lightly pull the switch up and then release it.
Page 82 4RUNNER (1998) Window lock button s’ OPERATING THE PASSENGER WINDOW Use the switch on the passenger’s door. The driver’s door also has a switch that controls the passengers’ window. The window moves as long as you hold the switch. To open: Push down the switch. To close: Pull up the switch.
Page 83 4RUNNER (1998)
Page 84 4RUNNER (1998) Power back window CAUTION To avoid serious personal injury, you must do the following. " Always make sure the head, hands and other parts of the body of all occupants are kept completely inside vehicle before you close the power win- dows.
Page 85 4RUNNER (1998) The back window can be operated with the inner switch on the center You can also open the back window console or outer switch on the back when the back window wiper is work- door. ing. At that time, the wiper stops OPERATING FROM INSIDE working until the window is closed again.
Page 86 4RUNNER (1998) With power window (driver’s door) Without power window (instrument panel)
Page 87 4RUNNER (1998) OPERATING FROM OUTSIDE After turning and holding the key for a few seconds. the back window will move as far as holding the key. To open: Turn the key counterclock- wise. To close: Turn the key clockwise. You can also open the back window when the back window wiper is work- ing.
Page 88 4RUNNER (1998) Back door " Always make sure the head, hands and other parts of the body of all occupants are kept completely inside vehicle before close power back window. someone’s neck, head hands gets caught in a closing window, it could result in a serious injury.
Page 89 4RUNNER (1998) LOCKING AND UNLOCKING WITH CAUTION Insert the key into the keyhole and turn it. Keep the back window and back To lock: Turn the key clockwise. door closed while driving. This To unlock: Turn the key counterclock- not only keeps the luggage from wise.
Page 90 4RUNNER (1998) Type A Driver’s side Front passenger’s side...
Page 91 4RUNNER (1998) Type B Driver’s side Front passenger’s side...
Page 92 4RUNNER (1998) Type C LOCKING AND UNLOCKING WITH Hood POWER BACK DOOR LOCK SWITCH Push the switch. lock: Push the switch on the ”LOCK” side. To unlock: Push the switch on the ”UNLOCK” side. Vehicles with a power door lock sys- tem—...
Page 93 4RUNNER (1998) To open the hood, do the following. 1. Pull the hood lock release lever. The hood will spring up slightly. CAUTION Before driving, be sure that the hood is securely locked. Other- wise, the hood may open unex- pectedly while driving and an ac- cident may occur.
Page 94 4RUNNER (1998) 2. In front of the vehicle, pull up on the a uxilialy catch lever and lift the hood. 3. Hold the hood open by inserting support rod into the slot.
Page 95 4RUNNER (1998) Before closing the hood, check to see Fuel tank cap that you have not forgotten any tools, rags, etc. and return the support rod to its clip- this prevents rattles. Then lower the hood make sure it locks into place.
Page 96 After removing the cap, wise till you hear a click. Toyota dealer as soon as possible. hang it on the cap hanger. If the cap is not tightened securely, the malfunction indicator lamp comes on.
Page 97 Make sure the cap is tightened securely to prevent fuel spillage in case of an accident. " Use only a genuine Toyota fuel tank cap for replacement. It has a built- in check valve to reduce fuel tank vacuum. Sliding operation...
Page 98 4RUNNER (1998) Tilting operation To close: Push the switch on the op- posite side of the ”SLIDE” side. To operate the moon roof, use the As a precaution when closing, the roof switches beside the interior light. stops three- quarters closed The moon roof works when the igni- position before fully closing.
Page 99 4RUNNER (1998) You may stop the moon roof at any " Never leave small children alone desired position. The roof will move in the vehicle, especially with while the switch is being pushed and the ignition key still inserted. stop when released. They could use the moon roof switches and get trapped in the CAUTION...
Page 100 4RUNNER (1998) Part 1 OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 1 Overview instru- ments and controls " Instrument panel overview " Instrument cluster overview " Indicator symbols on the instrument panel...
Page 101 4RUNNER (1998) Instrument panel overview 1. Side vent 2. Tilt steering lock release le- 3. Instrument cluster 4. Center vents 5. Personal lights 6. Electric moon roof switch 7. Glovebox 8. Power door lock switch 9. Power window switches 10. Automatic transmission se- lector lever or manual trans- mission gear shift lever 11.
Page 102 4RUNNER (1998) 1. Clutch start cancel switch 2. Headlight turn signal switch 3. Wiper and washer switches 4. Back window defogger switch 5. Emergency flasher switch 6. Clock 7. Cup holder 8. Air conditioning controls 9. Car audio 10. Ashtray 11.
Page 103 4RUNNER (1998) Instrument cluster overview 1. Service reminder indicators or indi- 4. Speedometer 7. Fuel gauge cator lights 5. Odometer 8. Trip meter reset knob 2. Engine coolant temperature gauge 6. Trip meter 3. Tachometer...
Page 104 4RUNNER (1998) Indicator symbols on the instrument panel Open door warning light Brake system warning light SRS airbag warning light Seat belt reminder light Unengaged ”Park” warning light Discharge warning light Low oil pressure warning light Automatic transmission fluid temperatu light Malfunction indicator lamp Low windshield washer fluid level warn...
Page 105 4RUNNER (1998) Automatic transmission indicator light Cruise control indicator light Driving pattern (”POWER” mode) indicator light Four- wheel drive indicator light Rear differential lock indicator light : For details, see ”Service reminder indicators and warning buzzers” in Chapter 1-5. : If this light flashes, see ”Cruise control” in Chapter 1-6.
Page 106 4RUNNER (1998) Part 1 Headlights and turn signals OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 4 Lights, Wipers and Defogger " Headlights and turn signals " Emergency flashers " Instrument panel light control " Interior light " Personal lights " Luggage compartment light "...
Page 107 4RUNNER (1998) HEADLIGHTS Under the daytime running light sys- tem, the headlights turn on at reduced To turn on the following lights: NOTICE intensity. Twist the knob to the posi- Twist the headlight/turn signal lever tion 2 to turn to full intensity for driv- knob.
Page 108 4RUNNER (1998) High- Low beams—For high beams, turn the headlights on and push the lever away from you (position 1). Pull the lever toward you (position 2) for low beams. The headlight high beam indicator light (blue light) on the instrument panel will tell you that the high beams are Flashing the high beam headlights (position 3)—Pull the lever all the way...
Page 109 4RUNNER (1998) TURN SIGNALS Emergency flashers To signal a turn, push the head- light/turn signal lever up or down to position 1. The key must be in the ”ON” position. The lever automatically returns after you make a turn, but you may have to return it by hand after you change lanes.
Page 110 4RUNNER (1998) To turn on the emergency flashers, Instrument panel light con- push the switch. trol NOTICE All the turn signal lights will flash. To turn them off, push the switch once To prevent the battery from being again. discharged, leave Turn on the emergency flashers to switch on longer than necessary...
Page 111 4RUNNER (1998) To adjust the brightness of Interior light instrument panel lights, turn the knob. To turn on the interior light, slide The interior light switch has the fol- the switch. lowing positions:...
Page 112 4RUNNER (1998) ”ON” Keeps the light on all the time. Personal lights ”OFF” Turns the light off. ”DOOR” Turns the light on when any of the side door is opened. The light goes off when all the side door is closed.
Page 113 4RUNNER (1998) To turn on the luggage compart- Ignition switch light ment light, slide the switch. The luggage compartment light switch has the following positions: ”ON” Keeps the light on all the time. ”OFF” Turns the light off. ”DOOR” Turns the light on when the back door is opened.
Page 114 4RUNNER (1998) Windshield wipers and washer (intermittent type) For easy access to the ignition switch, ignition switch light comes on when the driver’s door is opened. The light remains on for some time after driver’s door is closed.
Page 115 4RUNNER (1998) Windshield wipers and washer (mist type) To turn on the windshield wipers, move the lever to the desired set- To squirt washer fluid, pull the le- ting. ver toward you. The key must be in the ”ON” position. If the windshield wipers are off, they will operate a couple of times after Lever posi-...
Page 116 4RUNNER (1998) To turn on the windshield wipers, Back window wiper move the lever to the desired set- washer In freezing weather, warm the wind- ting. shield with the defroster before using The key must be in the ”ON” position. the washer.
Page 117 4RUNNER (1998) To turn on the back window wiper, Back window defogger twist the lever knob upward. NOTICE The key must be in the ”ON” position. Do not operate the back window Lever posi- Speed set- wiper if the back window is dry. tion ting It may scratch the glass.
Page 118 4RUNNER (1998) To defog or defrost the back win- dow, push the switch. Make sure you turn the defogger off The key must be in the ”ON” position. when the window is clear. Leaving the defogger on for a long time could The thin heater wires on the inside of cause the battery to discharge, espe- the back window will quickly clear the...
Page 119 4RUNNER (1998)
Page 120 4RUNNER (1998) Part 1 Fuel gauge OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 5 Gauges, Meters and Service reminder indicators " Fuel gauge " Engine coolant temperature gauge " Tachometer " Odometer and trip meter " Service reminder indicators warning buzzers...
Page 121 If the indicator lamp is turned off. does not go off, contact your Toyota dealer as soon as possible. If the fuel level approaches ”E” or the low fuel level warning light comes on,...
Page 122 4RUNNER (1998) gauge indicates engine Tachometer coolant temperature when the igni- " Idling for a long period with the air tion switch is on. The engine oper- conditioning on in stop- and- go traf- ating temperature will vary with fic. changes weather engine...
Page 123 4RUNNER (1998) tachometer indicates engine Odometer and trip meter speed in thousands of rpm (revolu- tions per minute). Use it while driv- ing to select correct shift points and to prevent engine lugging and overrevving. Driving with the engine running too fast causes excessive engine wear and poor fuel economy.
Page 124 4RUNNER (1998) Service reminder indicators and warning buzzers These meters show the running dis- tance. 1. Odometer—It shows the total dis- tance the vehicle has been driven. 2. Trip meter—It shows the distance driven since the last time it was set to zero.
Page 125 4RUNNER (1998) If the indicator or Do this. buzzer comes on... If parking brake is off, stop and check. Fasten seat belts. (Indicator and buzzer) Stop and check. Stop and check. Take vehicle to Toyota dealer. Fill up tank.
Page 126 If the indicator or Do this. buzzer comes on... Take vehicle to (type A) Toyota dealer. (type B) Close all doors. Take vehicle to Toyota d ealer immediately. Light reminder Turn off lights. buzzer (k) Key reminder Remove key. buzzer...
Page 127 4RUNNER (1998) If the indicator or Do this. buzzer comes on... Shift front drive control lever out of ”N”. Stop and check. Add washer fluid.
Page 128 (b) Seat Belt Reminder Light and place and stop the engine immediate- hicle carefully. There may be a prob- Buzzer ly. Call a Toyota dealer or qualified lem somewhere in the brake system. repair shop for assistance. Once the ignition key is turned to Check the fluid level of the see- ”ON”...
Page 129 (i) SRS Airbag Warning Light driving, have your vehicle checked by This lamp comes on in the following This light will come on when the your Toyota dealer as soon as pos- cases. ignition key is turned to the ”ACC” sible.
Page 130 ”N” position while the selector lever is airbag warning light light does not go off, call a Toyota in the ”P” position, the transmission should come on. It goes off after dealer or qualified repair shop for as- will disengage and the wheels will not about 6 seconds.
Page 131 4RUNNER (1998) If any service reminder indicator or warning buzzer does not function as described above, either the bulb is burned out or the circuit is in need of repair. Have it checked by your Toyo- ta dealer as soon as possible.
Page 132 4RUNNER (1998)
Page 133 4RUNNER (1998) Part 1 Clock OPERATION OF INSTRUMENTS AND CONTROLS— Chapter 1- 8 Other equipment " Clock " Cigarette lighter and ashtray " Power outlet " Glovebox " Auxiliary holder " Auxiliary box " Cup holder " Tie- down hooks "...
Page 134 4RUNNER (1998) The digital clock indicates the time. Cigarette lighter and ashtray The key must be in the ”ACC” or Once the electrical power source has ”ON” position. been disconnected from the clock, the time is automatically set to 1:00 (one To reset the hour: Push the ”H”...
Page 135 After using the ashtray, pressed in. push it back in completely. Use a Toyota genuine cigarette lighter To remove the ashtray, press down on or equivalent for replacement. the lock spring plate and pull out. CAUTION...
Page 136 4RUNNER (1998) The power outlet is designed for Glovebox power supply for car accessories. z Close the power outlet lid when The key must be in the ”ACC” or the power outlet is not in use. ”ON” position for the power outlet to Inserting a foreign object other be used.
Page 137 4RUNNER (1998) To use the glovebox, do this. Auxiliary holder To open: Pull the lever. To lock: Insert the master key and turn it clockwise. On some models, the glovebox light will come on when the golvebox is open with the instrument panel lights CAUTION To reduce the chance of injury in case of an accident or a sudden...
Page 138 4RUNNER (1998) To use the auxiliary holder, open Auxiliary box the lid. CAUTION To prevent vibration noise while driving, do not bend the holding clips.
Page 139 4RUNNER (1998) To open the box, turn the knob. Cup holder Front...
Page 140 4RUNNER (1998) Rear CAUTION The cup holder is designed for " holding cups or drink- cans securely Do not place anything else on in its holes. the cup holder, as such item may be thrown about in the To use the cup holder, pull it out. compartment and possibly in- jure people in the vehicle dur- ing sudden braking or an acci-...
Page 141 4RUNNER (1998) Tie- down hooks To secure your luggage, use the Luggage cover tie- down hooks as shown above. See ”Luggage stowage precautions” in Part 2 for what to observe in loading luggage.
Page 142 4RUNNER (1998) To use the luggage cover, pull it out of the retractor and hook it to the anchors. When opening the back door, turn back the dropleaf of the luggage cover to gain access to the back door lever inside the vehicle.
Page 143 4RUNNER (1998) To remove the luggage cover: Floor mat 1. Detatch its hooks from the head restraints. 2. Lift it up. Use a floor mat of the correct size.
Page 144 4RUNNER (1998) If the floor mat has a hole, then it is designed for use with a locking clip. Fix the floor mat and locking clip into the hole in the floor carpet. CAUTION Make sure the floor mat is prop- erly placed on the floor carpet.
Page 145: Steering Wheel And Mirrors
4RUNNER (1998) Part 1 Seats " While the vehicle is being driven, all Sun visors OPERATION OF vehicle occupants should have the seatback upright, sit well back in the INSTRUMENTS seat and properly wear the seat belts AND CONTROLS— provided. CAUTION Chapter 1- 3 "...
Page 146 4RUNNER (1998) Front seats— —Seat adjustment precaution —Adjusting front seats Adjust the driver’s seat so that the " While adjusting the seat, do not foot pedals, steering wheel and instru- put your hands under the seat ment panel controls are within easy or near the moving parts.
Page 147 4RUNNER (1998)
Page 148 4RUNNER (1998) —Adjusting front seats (power seat) 1. SEAT POSITION ADJUSTING LE- 3. SEAT CUSHION ANGLE ADJUST- ING KNOB Pull the lever up. Then slide the Turn the knob either way. seat to the desired position with 4. SEAT LUMBAR SUPPORT slight body pressure and release JUSTING LEVER...
Page 149 4RUNNER (1998)
Page 150 4RUNNER (1998) Fold- down rear seats 1. SEAT POSITION SEAT CAUTION CUSHION ANGLE ADJUSTING SWITCH To reduce the risk of sliding un- Move the control switch in the de- der the lap belt during a collision, sired direction. avoid reclining the seatback any Releasing the switch will stop the seat more than needed.
Page 151 4RUNNER (1998) BEFORE FOLD- DOWN REAR SEAT Stow the rear seat belts as shown in the illustration. This prevents the belts from falling out when you fold the seatback. NOTICE The seat belts must be stowed before you fold the seatback.
Page 152 4RUNNER (1998) 1. Remove the head restraint, and swing the bottom cushion up by " pulling the lock release strap. Be Make sure the bottom cushion certain to replace the head re- is securely locked by trying to straint. pull up the edge of the cushion near the lock release straps.
Page 153 4RUNNER (1998) 2. Unlock the seatback and fold it Head restraints down. CAUTION This will enlarge the luggage compart- ment as far as the raised seat cush- When returning the seatback to ion. See ”Luggage stowage precau- the upright position: tions”...
Page 154 4RUNNER (1998) Front Rear On some models, you can also move the head restraint forward or back- For your safety, adjust the head re- ward. If such adjustment is desired, straint before driving. pull or push the head restraint. To raise: Pull it up. To lower: Push it down while pressing the lock release button.
Page 155 —Seat belt precautions The head restraint is most effective when it is close to your head. There- Toyota strongly urges that the driver Do not allow the child to stand up or fore, using a cushion on the seatback and passengers in the vehicle be kneel on either rear or front seats.
Page 156 4RUNNER (1998) CAUTION " Avoid reclining the seatbacks Persons should ride in their seats too much. The seat belts pro- properly wearing their seat belts vide maximum protection when whenever the vehicle is moving. the seatbacks are in the upright Otherwise, they are much more position.
Page 157 (For details, see ”Child restraint” in may lock if you lean forward too tact your Toyota dealer. Do not this chapter.) To free the belt again, quickly. A slow, easy motion will allow use the seat until the seat belt...
Page 158 4RUNNER (1998) Seat belts with an adjustable shoul- der anchor— CAUTION Adjust the shoulder anchor position to your size. Always make sure the shoulder To raise: Slide the anchor up. belt is positioned across the cen- To lower: Push in the lock release ter of your shoulder.
Page 159 4RUNNER (1998) Take up slack Too high Keep as low on hips as possible Adjust the position of the lap and shoulder belts. CAUTION Position the lap belt as low as pos- sible on your hips—not on your waist, " High- positioned lap belts and then adjust it to a snug fit by pulling loose- fitting belts both could...
Page 160 4RUNNER (1998) release belt, press —Rear center seat belt buckle- release button and allow the belt to retract. If the belt does not retract smoothly, pull it out and check for kinks or twists. Then make sure it remains un- twisted as it retracts.
Page 161 " If the seat belt does not func- tion normally, immediately con- tact your Toyota dealer. Do not use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child...
Page 162 4RUNNER (1998) Too high Adjust to a snug fit Keep as low on hips as possible Remove excess length of the belt and adjust the belt position. To shorten the belt, pull the free end of the belt. Position the lap belt as low as pos- sible on your hips—not on your waist, then adjust it to a snug fit.
Page 163 4RUNNER (1998) release belt, press —Stowing rear seat belts buckle- release button. The rear seat belts can be stowed Seat belts must be stowed before you —Seat belt extender when not in use. fold seat back. (See ”Rear seats—Fold down rear seat” in this chapter.)
Page 164 If your seat belt cannot be fastened securely because it is not long enough, a personalized seat belt extender is available from your Toyota dealer free of charge. Please contact your local Toyota deal- er so that the dealer can order the proper required length for the extend- er.
Page 165 In response to a severe frontal im- injured. Toyota strongly recom- pact, the SRS airbags work together mends that: with the seat belts to help prevent or "...
Page 166 4RUNNER (1998) This indicator comes on when the ignition key is turned to the ”ACC” or ”ON” position. It goes off after about 6 seconds. This means the SRS airbags are operating properly. The SRS airbag warning light system monitors the airbag sensor assembly, inflators, warning light, interconnecting wiring and power sources.
Page 167 4RUNNER (1998) The SRS airbag system is designed to activate in response to a severe However, this threshold velocity will frontal impact within the shaded be considerably higher if the vehicle area between the arrows in the il- strikes an object, such as a parked lustration.
Page 168 4RUNNER (1998) Collision from the rear Collision from the side Vehicle roll- over The SRS airbags are not designed to inflate if the vehicle is subjected to a side or rear impact, if it rolls over, or if it is involved in a low- speed frontal collision.
Page 169 4RUNNER (1998) The SRS airbag system mainly con- sists of the following components and In a severe frontal impact, sensors their locations are shown in the il- CAUTION detect deceleration and the system lustration. triggers the airbag inflators. Then a "...
Page 170 Toyota strong- ly recommends that all infants and children be placed in the rear seat of the vehicle and properly restrained.
Page 171 4RUNNER (1998) " Never put a rear- facing child restraint system in the front seat because the force of the rapid inflation of the passenger airbag can cause death or seri- ous injury to the child. Move seat fully back "...
Page 172 4RUNNER (1998) " Do not sit on the edge of the seat or lean over the dashboard when the vehicle is in use. The airbags inflate with considerable speed and force; you may be killed or seriously injured. Sit up straight and well back in the seat, and always use your seat belt.
Page 173 4RUNNER (1998) " Do not allow a child to stand up, or to kneel on the front passenger seat. The airbag in- flates with considerable speed and force; the child may be killed or seriously injured. " Do not hold a child on your lap or in your arms.
Page 174 4RUNNER (1998) " Do not put objects or your pets on or in front of the dashboard " Do not modify or remove any steering wheel that wiring. Do not modify, remove, houses the airbag system. They strike or open any components might restrict inflation or cause such as the steering wheel col- death or serious injury as they...
Page 175 4RUNNER (1998) NOTICE Do not perform any of the follow- ing changes without consulting your Toyota dealer. Such changes can interfere with proper operation of the SRS airbag system in some cases. z Installation of electronic items such as a mobile two- way ra-...
Page 176 If either of the following conditions occurs, this indi- cates a malfunction of the airbags. Contact your Toyota dealer as soon as possible to service the vehicle. " The light does not come on when the ignition key is turned to the ”ACC”...
Page 177 4RUNNER (1998) Child restraint— —Child restraint precaution In the following cases, contact your CAUTION Toyota dealer as soon as possible: Toyota strongly urges the use of " The SRS airbags have been in- " child restraint systems for children For effective protection in auto- flated.
Page 178 4RUNNER (1998) —Child restraint system " Toyota strongly urges use of a A child restraint system for a small proper child restraint system child or baby must itself be proper- which conforms to the size of ly restrained on the seat with either...
Page 179 " Never put a rear- facing child the passenger compartment. This will from your Toyota dealer. restraint system on the front prevent it from injuring passengers in * CRS installation kit seat. In the event of an acci- the event of a sudden stop or acci- (Part No.
Page 180 4RUNNER (1998) —Types of child restraint sys- Child restraint systems are classified into the following 3 types depending on the child’s age and size. (A) Infant seat (B) Convertible seat (C) Booster seat Install the child restraint system fol- lowing the instructions provided by its manufacturer.
Page 181 4RUNNER (1998) (B) Convertible seat...
Page 182 4RUNNER (1998) (C) booster seat...
Page 183 4RUNNER (1998) —Installation with 2- point type seat belt (A) INFANT SEAT INSTALLATION An infant seat is used in rear- fac- ing position only.
Page 184 4RUNNER (1998) CAUTION Do not put a rear- facing child re- straint system on the rear seat if it interferes with the lock mecha- nism of the front seats. This can cause severe injury to the child and front passenger in case of sudden braking or a collision.
Page 185 " seat belt does function normally, cannot protect your child from injury. Contact your Toyota dealer immediately. Do not seat until the seat belt is fixed.
Page 186 4RUNNER (1998) 2. While pressing the infant seat firm- ly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the in- fant seat securely. CAUTION Push and pull the child restraint system in different directions to be sure it is secure.
Page 187 4RUNNER (1998) 3. To remove the infant seat, press the buckle- release button. (B) CONVERTIBLE SEAT INSTALLA- TION...
Page 188 4RUNNER (1998) A convertible seat is used in for- ward- facing and rear- facing posi- tion depending on the child’s age and size. When installing, follow the manufacturer’s instructions about the applicable child’s age and size as well as direction for installing of a child restraint system.
Page 189 " seat belt does function normally, cannot protect your child from injury. Contact your Toyota dealer immediately. Do not seat until the seat belt is fixed.
Page 190 4RUNNER (1998) 2. While pressing the convertible seat firmly against the seat cushion and seatback, tighten the lap belt by pulling its free end to hold the con- vertible seat securely.
Page 191 4RUNNER (1998) —Installation with 3- point type seat belt CAUTION Push and pull the child restraint system in different directions to be sure it is secure. Follow all the installation instructions pro- vided by its manufacturer. 3. To remove the convertible seat, press the buckle- release button.
Page 192 4RUNNER (1998) (A) INFANT SEAT INSTALLATION An infant seat is used in rear- fac- ing position only.
Page 193 4RUNNER (1998) CAUTION " Never put a rear- facing child restraint system in the front seat because the force of the rapid inflation of the passenger airbag can cause death or seri- ous injury to the child. " Do not put a rear- facing child restraint system in the rear seat if it interferes with the lock mechanism of the front seats.
Page 194 " seat belt does function normally, cannot protect your child from injury. Contact your Toyota dealer immediately. Do not seat until the seat belt is fixed.
Page 195 4RUNNER (1998) 2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted even slightly, it cannot be extended. To hold the infant seat securely, make sure the belt is in the lock mode be- fore letting the belt retract.
Page 196 4RUNNER (1998) 3. While pressing the infant seat firm- ly against the seat cushion and seatback, let the shoulder belt re- tract as far as it will go to hold the infant seat securely.
Page 197 4RUNNER (1998) CAUTION Make sure the seat belt is secure- ly locked. Also make sure the child restraint system is secure by pushing and pulling it in dif- ferent directions. Follow all the installation instructions provided by its manufacturer. 4. To remove the infant seat, press the buckle- release button and allow the belt to retract completely.
Page 198 4RUNNER (1998) (B) CONVERTIBLE SEAT INSTALLA- TION A convertible seat is used in for- ward- facing and rear- facing posi- tion depending on the child’s age and size. When installing, follow the manufacturer’s instructions about the applicable child’s age and size as well as directions for installing a child restraint system.
Page 199 4RUNNER (1998) CAUTION " Never put a rear- facing child restraint system in the front seat because the force of the rapid inflation of the passenger airbag can cause death or seri- ous injury to the child.
Page 200 4RUNNER (1998) Move seat fully back " A forward- facing child restraint system should be allowed to put on the front seat only when it is unavoidable. Always move the seat as far back as pos- sible, because the force of a deploying airbag could cause death or serious injury to the child.
Page 201 4RUNNER (1998) " Do not put a rear- facing child restraint system in the rear seat if it interferes with the lock mechanism of the front seats. This can cause severe injury to the child and front passenger in case of sudden braking or a collision.
Page 202 " seat belt does function normally, cannot protect your child from injury. Contact your Toyota dealer immediately. Do not seat until the seat belt is fixed.
Page 203 4RUNNER (1998) 2. Fully extend the shoulder belt to put it in the lock mode. When the belt is then retracted slightly, it cannot be extended. To hold the convertible seat securely, make sure the belt is in the lock mode before letting the belt retract.
Page 204 4RUNNER (1998) 3. While pressing the convertible seat firmly against the seat cushion and seatback, let the shoulder belt re- tract as far as it will go to hold the convertible seat securely.
Page 205 4RUNNER (1998) CAUTION Make sure the seat belt is secure- ly locked. Also make sure the child restraint system is secure by pushing and pulling it in dif- ferent directions. Follow all the installation instructions provided by its manufacturer. 4. To remove the convertible seat, press buckle- release button...
Page 206 4RUNNER (1998) (C) BOOSTER SEAT INSTALLATION A booster seat is used in forward- facing position only. Move seat fully back...
Page 207 4RUNNER (1998) CAUTION A forward- facing child restraint system should be allowed to put on the front seat only when it is unavoidable. Always move seat as far back as possible, be- cause the force of a deploying airbag could cause death or seri- ous injury to the child.
Page 208 Contact your Toyota dealer child’s shoulder. Failure to do immediately. Do not so could reduce the amount of seat until the seat belt is fixed.
Page 209 4RUNNER (1998) —Top strap anchors and locations 2. To remove the child restraint sys- tem, press the buckle- release but- ton and allow the belt to retract. If your child restraint system re- See the following instructions to install quires the use of a top strap, latch the anchor bracket.
Page 210 If your child restraint system does not provide any of the necessary parts, c. Insert a 15 mm (0.6 in.) spacer ask your Toyota dealer. (See ”—Child and tighten down the anchor bracket restraint system”.) for your child restraint system with a bolt.
Page 211 4RUNNER (1998) To change the steering wheel angle, Outside rear view mirrors— hold the steering wheel, pull up the lock release lever, tilt the steering wheel to the desired angle and re- lease the lever. When the steering wheel is in a low position, it will spring up as you re- lease the lock release lever.
Page 212 4RUNNER (1998) —Power Rear view mirror control Adjust the mirror so you can see the side of your vehicle in the mir- ror. CAUTION Be careful when judging the size or Do not adjust the mirror while the distance of any object seen in the vehicle is moving.
Page 213 4RUNNER (1998) With power window (door armrest) Without power window (instrument Place the switch at ”L” (left) or ”R” panel) (right). adjust mirror, 2. Control switch—To move the mir- switches. ror P ush the switch in the desired 1. Master switch—To select the mirror direction.
Page 214 4RUNNER (1998) Anti- glare inside rear view mirror If the engine is not running, the key —Folding rear view mirrors must be in the ”ACC” position. NOTICE If ice should jam the mirror, do not operate the control or scrape the mirror face.
Page 215 4RUNNER (1998) Sun visors— —Vanity mirrors To reduce glare from the headlights of the vehicle behind you during night driving, operate the lever on the lower edge of the mirror. Daylight driving—Lever at position 1 The reflection in the mirror has great- er clarity at this position.
Page 216 4RUNNER (1998) To use the vanity mirrors, swing down the sun visor and open the cover. On some models, the vanity light comes on when you open the cover.
Page 217 If the seat belt does not func- When not in use, remove the extender tion normally, immediately con- tact your Toyota dealer. Do not and store in the vehicle for future use. use the seat until the seat belt is fixed. It cannot protect an adult occupant or your child from injury.
Page 218 " Facts about engine oil consumption " Twin ground electrode spark plugs " Brake system " Brake wear limit indicators " Luggage stowage precautions " Your Toyota’s identification " Theft prevention labels " Suspension and chassis " Types of tires...
Page 219 4RUNNER (1998) This vehicle is one of the class of vehicles which have higher ground clearance narrower tread relation to the height of their center of gravity to make them capable of performing in a wide variety of off- road applications. Specific design characteristics give it a higher cen- ter of gravity than ordinary cars.
Page 220 4RUNNER (1998) Break- in period CAUTION Drive gently and avoid high speeds. " When driving off- road Always observe the following pre- Your vehicle does not need an elabo- rugged terrain, do not drive at cautions to minimize the risk of rate break- in.
Page 221 To help prevent gas station mixups, Use of unleaded gasoline with an oc- gasolines. The AAMA specification your Toyota has a new smaller fuel tane rating or research octane number offers optimal fuel information for tank opening. The special nozzle on...
Page 222 4RUNNER (1998) Operation in foreign coun- tries GASOLINES CONTAINING MMT NOTICE If you plan to drive your Toyota in Some gasolines contain z Do not use gasohol other than another country... octane- enhancing additive called stated above. It will cause fuel...
Page 223 4RUNNER (1998) Three- way catalytic convert- The three- way catalytic converter is an emission control device installed in the exhaust system. The purpose is to reduce pollutants in the exhaust gas. CAUTION " Keep people and combustible materials away from the exhaust pipe while the engine is run- ning.
Page 224 Remember, your Toyota dealer change in the sound of the ex- load on the three- way catalytic knows...
Page 225 4RUNNER (1998) Facts about engine oil consumption " FUNCTIONS OF ENGINE OIL Oil is also used to lubricate the " Keep the back door and back stems of the intake valves. Some Engine oil has the primary functions window closed while driving. An of this oil is sucked into the com- of lubricating and cooling the inside of open or unsealed back door and...
Page 226 Therefore, it is essential that the oil level be checked regularly. Toyota rec- ommends that the oil level be checked every time you refuel the vehicle.
Page 227 4RUNNER (1998) Your engine fitted with twin The brake booster uses engine vacu- Brake system ground electrode spark plugs. um to power- assist the brakes. If the TANDEM MASTER CYLINDER engine should quit while you are driv- BRAKE SYSTEM NOTICE ing, you can bring the vehicle to a tandem master cylinder brake...
Page 228 4RUNNER (1998) Effective way to press ”ABS” Always maintain a safe distance from " Even the power assist brake pedal: When the anti- lock brake the vehicle in front of you. Compared completely lost, the brakes will system function is in action, you may with vehicles not fitted with an anti- still work.
Page 229 4RUNNER (1998) Type A Type B This light comes on when the ignition key is turned to the ”ON” position. ”ABS” warning light After about 3 seconds, the light will go off.
Page 230 Contact your ing brake performance so that the Toyota dealer as soon as possible to wheels can lock- up during sudden service the vehicle.
Page 231 Be sure all items are se- pads checked and replaced by your luggage or packages low, as cured in place. Toyota dealer as soon as possible. close to the floor as possible. " Expensive rotor damage can result if Be careful to keep the vehicle bal- "...
Page 232 4RUNNER (1998) Your Toyota’s identification— —Vehicle identification numb " Do not place anything on the filler panel or luggage cover. Such items thrown about possibly injure people the vehicle during sudden braking or an accident. (secure items safe place.) "...
Page 233 This number is on the left top of the instrument panel, and can be seen through the windshield from outside. This is the primary identification num- ber for your Toyota. It is used in reg- istering the ownership of your vehicle.
Page 234 4RUNNER (1998) The vehicle identification number (VIN) —Engine number is also on the Certification Label. 3RZ-FE engine 3RZ- FE engine...
Page 235 4RUNNER (1998) Theft prevention labels (except for Canada) 5VZ-FE engine 5VZ- FE engine The engine number is stamped on Your new vehicle carries theft pre- the engine block as shown. vention labels which are approxi- mately 56 mm (2.20 in.) by 16 mm (0.63 in.).
Page 236 4RUNNER (1998) Suspension and chassis Types of tires NOTICE Determine what kind of tires your You should not attempt to remove CAUTION vehicle is originally equipped with. the theft prevention labels as it 1. Summer tires may violate certain state or feder- Do not modify the suspension/ al laws.
Page 237 4RUNNER (1998) CAUTION " Do not mix summer and all sea- son tires on your vehicle as this can cause dangerous han- dling characteristics, resulting in loss of control. " Do not use tire other than the manufacturer’s designated tires, and never mix tires or wheels of the sizes different from the originals.
Page 238 4RUNNER (1998)
Page 239 4RUNNER (1998) How to start the engine— (a) Before cranking Part 3 Before starting the engine 1. Check the area around the vehicle 1. Apply the parking brake firmly. STARTING AND before entering it. 2. Turn off unnecessary lights and ac- DRIVING 2.
Page 240 See ”If your vehicle will not start” in lightly pressing the brake pedal Part 4. with the parking brake pulled. If they still do not work safely, pull to the side of the road and call a Toyota dealer for assistance.
Page 241 4RUNNER (1998) CAUTION " Four- wheel drive models—Toyota " Be careful when accelerating, " recommends not using four- wheel Before driving off, make sure upshifting, downshifting drive on dry hard- surfaced roads, that the parking brake is fully braking on a slippery surface.
Page 242 4RUNNER (1998) Off- road driving precaution Always observe the following pre- When driving your vehicle off- road, cautions to minimize the risk of CAUTION please observe the following precau- serious personal injury or damage tions to ensure your driving enjoyment to your vehicle: and to help prevent the closure of "...
Page 243 Take all necessary safety mea- Schedule”. how to visually inspect the battery. sures to ensure that water dam- Your Toyota dealer and most service age to the engine or other com- stations will be pleased to check the ponents does not occur.
Page 244 Ask your local Toyota dealer for further details before towing. your parking brake WEIGHT LIMITS...
Page 245 4RUNNER (1998) CAUTION " The total trailer weight (trailer weight plus cargo load) must not exceed the following. Exceeding this weight is dan- gerous. If towing a trailer over 907 kg (2000 lb.), it is neces- sary to use a sway control de- vice with a sufficient capacity.
Page 246 4RUNNER (1998) " The gross vehicle weight must not exceed the Gross Vehicle Weight Rating (GVWR) indicated on the Certification Label. The gross vehicle weight is the sum of weights of the unloaded ve- hicle, driver, passengers, lug- gage, hitch and trailer tongue load.
Page 247 After removal of the hitch, maximum of the following. Nev- Toyota does not recommend using seal the installation area to prevent er load the trailer with more a weight distribution (load equaliz- entry of exhaust fumes and mud.
Page 248 " curely loaded so that it cannot ched to both the trailer and the Toyota recommends that you do shift. vehicle. If damage occurs to the not tow a trailer with a new vehicle "...
Page 249 4RUNNER (1998) " " TRAILER TOWING TIPS Because stopping distance may be Crosswinds and rough roads will increased, vehicle- to- vehicle dis- adversely affect handling of your When towing a trailer, your vehicle tance should be increased when vehicle and trailer, causing sway. will handle differently than when towing a trailer.
Page 250 4RUNNER (1998) 5. Shift into first or reverse (manual) or ”P” (automatic) and turn off the " Because of the added load of the When restarting out after parking on engine. trailer, your vehicle’s engine may a slope: overheat on hot days (at tempera- 1.
Page 251 4RUNNER (1998) How to save fuel and make your vehicle last longer, too " Getting more kilometers/mileage from Avoid continuous speeding up " Slow down and downshift be- a liter/gallon of fuel is easy—just take and slowing down. Stop- and- go fore descending steep or long it easy.
Page 252 4RUNNER (1998) " Keep the bottom of your vehicle free from mud, etc. This not only lessens weight but also helps pre- vent corrosion. " Keep your vehicle tuned- up and in top shape. A dirty air cleaner, improper valve clearance, dirty plugs, dirty oil and grease, brakes...
Page 253 4RUNNER (1998)
Page 254 " If you lose your keys repair. Call a Toyota dealer or quali- fied repair shop. NOTICE Do not pull- or push- start the ve- hicle. It may damage the vehicle or cause a collision when the en- gine starts.
Page 255 If the engine still will not start, it " Batteries contain sulfuric acid needs adjustment or repair. Call a which is poisonous and corro- Toyota dealer or qualified repair shop sive. Wear protective safety for assistance. glasses when jump starting, and...
Page 256 4RUNNER (1998) JUMP STARTING PROCEDURE 1. If the booster battery is installed in another vehicle, make sure the ve- hicles are not touching. Turn off all unnecessary lights and accesso- ries. 2. If required, remove all the vent plugs from the booster and dis- charged batteries.
Page 257 4RUNNER (1998) Discharged battery Booster battery Positive terminal (”+” mark) Positive terminal Jumper cable (”+” mark) 4. Make the cable connections in the order a, b, c, d. a. Connect the clamp of the posi- tive (red) jumper cable to the posi- tive ( ) terminal on the discharged battery.
Page 258 4RUNNER (1998) Jumper cable Negative terminal Discharged (”-” mark) battery Booster battery c. Connect the clamp of the nega- tive (black) jumper cable to the negative terminal booster battery. d. Connect the clamp at the other end of the negative (black) jumper cable to a solid, stationary, un- painted, metallic point of the ve- hicle with the discharged battery.
Page 259 4RUNNER (1998) Connecting point for 5VZ- FE engine Connecting point for 3RZ- FE engine Do not connect it to or near any part that moves when the engine is cranked.
Page 260 4RUNNER (1998) If your engine stalls while driving If your vehicle overheats CAUTION If your engine stalls while driving... If your engine coolant temperature gauge indicates overheating, if you When making the connections, to 1. Reduce your speed gradually, keep- experience a loss of power, or if avoid serious injury, do not lean ing a straight line.
Page 261 4. If the engine drive belt is broken possible at your Toyota dealer. or the coolant is leaking, stop the CAUTION engine immediately. Call a Toyota dealer for assistance. When jacking, be sure to observe 5.
Page 262 4RUNNER (1998) —Required tools and spare tire " NOTICE Stop the vehicle on a level firm ground, firmly set the parking Do not continue driving with a brake and put the transmission deflated tire. Driving even a short in ”P” (automatic) or reverse distance can damage a tire be- (manual).
Page 263 4RUNNER (1998) Cover (on some models) 1. Get the required tools and spare tire. 1. Tool bag 2. Jack handle 3. Jack To prepare yourself for an emergency, you should familiarize yourself with the use of the jack, each of the tools and their storage locations.
Page 264 4RUNNER (1998) Turn the jack joint by hand. To remove: Turn the joint in direction 1 until the jack is free. To store: Turn the joint in direction 2 until the jack is firmly secured to pre- vent it flying forward during a collision or sudden braking.
Page 265 4RUNNER (1998) To remove the spare tire: —Blocking the wheel 1. Insert the end of the jack handle into the lowering screw and turn it counterclockwise. 2. After the tire is lowered completely to the ground, remove the holding bracket. When storing the spare tire, put it in place with the outer side of the wheel facing up.
Page 266 4RUNNER (1998) 2. Block the wheel diagonally oppo- —Removing wheel ornament site the flat tire to keep the ve- hicle from rolling when jacked up. When blocking the wheel, place a wheel block from the front for the front wheels or from the rear for the rear wheels.
Page 267 4RUNNER (1998) Steel wheels Aluminum wheels 3. Remove the wheel ornament. Pry off the wheel ornament, using the beveled end of the wheel nut wrench as shown.
Page 268 4RUNNER (1998) —Loosening wheel nuts CAUTION Do not try to pull off the orna- ment by hand. Take due care in handling the ornament to avoid unexpected personal injury. 4. Loosen all the wheel nuts. Do not remove the nuts yet—just un- —Positioning the jack screw them about one- half turn.
Page 269 4RUNNER (1998) 5. Position the jack at the correct —Raising your vehicle jack point as shown. Make sure the jack is positioned on a level and solid place.
Page 270 4RUNNER (1998) 6. After making sure that no one is —Changing wheels vehicle, raise high enough so that the spare tire CAUTION can be installed. Never get under the vehicle when Remember you will need more ground clearance when putting on the spare the vehicle is supported by the jack alone.
Page 271 4RUNNER (1998) Roll the spare wheel into position and align the holes in the wheel with the bolts. Then lift up the wheel and get at least the top bolt started through its hole. Wiggle the tire and press it back over the other bolts.
Page 272 4RUNNER (1998) 8. Reinstall all the wheel nuts fin- —Lowering your vehicle ger tight. Reinstall the wheel nuts (tapered end inward) and tighten them as much as you can by hand. Press back on the tire back and see if you can tighten them more.
Page 273 4RUNNER (1998) 9. Lower the vehicle completely and —Reinstalling wheel orna- tighten the wheel nuts. ment CAUTION Turn the jack handle extension coun- terclockwise with handle to lower the When lowering the vehicle, make vehicle, making sure the handle re- sure all portions of your body mains firmly fitted onto the jack han- and all other persons around will...
Page 274 4RUNNER (1998) 10. Reinstall the wheel ornament. As soon as possible after changing —After changing wheels wheels, tighten the wheel nuts to the Put the wheel ornament into position 11. Check the air pressure of the re- torque specified in Part 8 with a and then tap it firmly with the side or placed tire.
Page 275 4RUNNER (1998) If your vehicle needs to be towed— (a) Towing with wheel lift type truck —From front —From rear (b) Using flat bed truck Two- wheel drive models...
Page 276 (b) Using flat bed truck Four- wheel drive models If towing is necessary, we recom- mended you to have it done by your Toyota dealer or a commercial tow truck service. In consultation with them, have your vehicle towed using either (a) or (b).
Page 277 4RUNNER (1998) Only when you cannot receive a towing service from a Toyota dealer TOWING PRECAUTIONS: From rear—Place the ignition key in or commercial tow truck service, the ”ACC” position. Use a safety chain system for all tow- tow your vehicle carefully in accor-...
Page 278 4RUNNER (1998) Four-wheel drive models— From rear—We recommend using a towing dolly under the front wheels. If (a) Towing with wheel lift type truck you do not use a towing dolly, place From front— the ignition key in the ”ACC” position, "...
Page 279 4RUNNER (1998) (c) Towing with sling type truck All models— —Emergency towing (c) Towing with sling type truck NOTICE Do not tow with sling type truck, either from the front or rear. This may cause body damage.
Page 280 4RUNNER (1998) If towing is necessary, we recom- NOTICE mend you to have it done by your Toyota dealer or a commercial tow Use only a cable or chain specifi- CAUTION truck service. cally intended for use in towing vehicles. Securely fasten the cable...
Page 281 " If the towing vehicle can hardly move, do not forcibly continue the towing. Contact your Toyota dealer commercial truck service for assistance. " vehicle straight ahead as possible.
Page 282 4RUNNER (1998) If you cannot shift automat —Tips for towing a stuck transmission selector lever vehicle (two- wheel drive models) The following methods are effective to get out when your vehicle is struck in mud, sand or other condition from which the vehicle cannot be driven out under its own power.
Page 283 4. Shift into ”N” position. 5. Insert the cover. 6. Start the engine. For your safety, keep the brake pedal depressed. Be sure to have the system checked by your Toyota dealer as soon as possible.
Page 284 4RUNNER (1998) If you cannot shift the selector le- ver out of ”P” position to other positions even though the brake pedal is depressed, use the shift lock override button as follows: 1. Turn the ignition key to ”LOCK” position. Make sure the parking brake is set.
Page 285 6. Start the engine. For your safety, and you cannot get a duplicate, many keep the brake pedal depressed. Toyota dealers can still open the door for you, using their special tools. If Be sure to have the system checked...
Page 286 Now, it is up to " High temperatures will cause corro- CARE you. Proper care of your Toyota can sion to those components of the help ensure long- term corrosion pre- vehicle which are prevented from vention.
Page 287 Check the condition of your ve- " Your Toyota dealer will be happy to When the vehicle becomes remark- hicle’s paint and trim. If you find any assist in supplying and installing the...
Page 288 Toyota’s finish. 2. Wash with a mild car- wash soap, some type brushes, unfiltered Once a month or if the vehicle does...
Page 289 4RUNNER (1998) Cleaning the interior NOTICE NOTICE CAUTION Do not use solvent, thinner, gaso- Do not use dye or bleach on the Do not wash the vehicle floor line or window cleaner on the in- belts—it may weaken them. with water, or allow water to get terior.
Page 290 If you have any questions about the gasoline, or alkaline or acid z If you use a liquid car freshen- cleaning of your Toyota, your local solutions for cleaning the leath- Toyota dealer will be pleased to er, do not apill the liquid onto er as these could cause discol- answer them.
Page 291 4RUNNER (1998)
Page 292: Maintenance And Care
4RUNNER (1998) Part 6 Maintenance requirements Your Toyota vehicle has been de- Scheduled maintenance VEHICLE signed to for fewer maintenance re- scheduled maintenance items quirements with longer service inter- MAINTENANCE listed in the ”Owner’s Manual Supple- vals to save both your time and ment/Maintenance Schedule”...
Page 293 You can be confident that your Toyota or the qualified service shop for their dealer’s service department performs advice. the best job to meet the maintenance requirements on your vehicle—reliably...
Page 294 4RUNNER (1998) Tire surface and wheel nuts INSIDE THE VEHICLE Seat belts Check the tires carefully for cuts, Check that the seat belt system such Items listed below should damage or excessive wear. See Chap- as buckles, retractors and anchors op- checked regularly, e.g.
Page 295 4RUNNER (1998) Does your vehicle need repairing? Automatic transmission ”Park” mech- Brake fluid level Be on the alert for changes in perfor- anism Make sure the brake fluid level is cor- mance, sounds, and visual tip- offs Check the lock release button of the rect.
Page 296 4RUNNER (1998) If you notice any of these clues, take your vehicle to your Toyota dealer as soon as possible. It probably needs adjustment or repair. CAUTION Do not continue driving with the vehicle unchecked. It could result in serious vehicle damage and...
Page 297 4RUNNER (1998)
Page 298 4RUNNER (1998) Part 7 Checking the engine oil level DO- IT- YOURSELF MAINTENANCE— Chapter 7- 2 Engine and Chassis " Checking the engine oil level " Checking the engine coolant level " Checking brake fluid " Checking power steering fluid "...
Page 299 4RUNNER (1998) Low level Full level Type A Type B Add oil O.K. Too full With the engine at operating tem- 5VZ- FE engine perature and turned off, check the 1.2 (1.3, 1.1) If the oil level is below or only oil level on the dipstick.
Page 300 4RUNNER (1998) Use API grade SH, ”Energy- Conserv- Recommended viscosity (SAE): II” “Energy- conserving” ENGINE OIL SELECTION multigrade engine oil or ILSAC multi- grade engine oil. SAE 5W- 30 is the best choice for your vehicle, for good fuel economy and good starting in cold weather.
Page 301 4RUNNER (1998) API service symbol ILSAC certification mark The API Service Symbol is located anywhere on the outside of the con- Oil identification marks tainer. Either or both API registered marks are added to some oil containers to help you select the oil you should use.
Page 302 See information in the next column. in Part 8. We recommend 50% solu- tion be used for your Toyota, or a If the coolant level drops within a sufficient quantity to provide protection...
Page 303 4RUNNER (1998) Checking brake fluid To check the fluid level, simply look NOTICE at the see- through reservoir. The Remove replace reservoir level should be between the ”MAX” If you spill the fluid, be sure to cover by hand. and ”MIN” lines on the reservoir. wash it off with water to prevent Use only newly opened brake fluid.
Page 304 4RUNNER (1998) Checking power steering fluid If cold add If cold O.K. If hot add If hot O.K. Check the fluid level on the dip- CAUTION stick. If necessary, add automatic c. Reinstall the filler cap. transmission fluid DEXRONrII or III. The reservoir tank may be hot so d.
Page 305 Without the valve If a tire frequently needs refilling, caps, dirt or moisture could get have it checked by your Toyota deal- into the valve core and cause air leakage. If the caps have been lost, have new ones put on as...
Page 306 If any damage is found, consult greater load capacity. with a technician and have the tire The tires on your Toyota have built- in repaired or replaced. tread wear indicators to help you...
Page 307 Do not use tires or wheels oth- er than the manufacture’s rec- ommended size. Toyota recommends all four tires, or at least both of the front or rear tires be replaced at a time as a set. See ”If you have a flat tire” in Part 4 for tire change procedure.
Page 308 Installing snow tires and chains To equalize tire wear and help ex- SNOW TIRE INSTALLATION tend tire life, Toyota recommends Snow tires should be installed on WHEN TO USE SNOW TIRES OR that you rotate your tires approxi- all wheels.
Page 309 Correct replacement wheels are avail- check them before installing chains. able at your Toyota dealer. CHAIN INSTALLATION A wheel of a different size or type Install the chains on the rear tires may adversely affect handling, wheel as tightly as possible.
Page 310 When using tire chains, be careful wheel which is designed for a tube- damage aluminum less tire. wheels. " Use only the Toyota wheel nuts and wrench designed for your alu- minum wheels. " When balancing your wheels, use only Toyota balance...
Page 311 4RUNNER (1998) Checking battery condition— —Precautions Part 7 DO- IT- YOURSELF " CAUTION If electrolyte gets on your skin, thoroughly wash contact MAINTENANCE— BATTERY PRECAUTIONS area. If you feel pain or burn- ing, get medical attention im- The battery produces flammable mediately.
Page 312 4RUNNER (1998) —Checking battery exterior Terminals Ground cable Hold- down clamp Check the battery for corroded or —Checking battery fluid loose terminal connections, cracks, or loose hold- down clamp. NOTICE If the battery is corroded, wash it z Be sure the engine and all ac- off with a solution of warm water cessories are off before per- and baking soda.
Page 313 Only do a slow charge (5A or DARK WHITE Have battery checked disconnect the ground cable. less). Charging at a quicker rate by your Toyota dealer. 2. Be sure the power switch on the is dangerous. The battery may CLEAR or Have battery...
Page 314 4RUNNER (1998) Checking replacing fuses NOTICE Never recharge the battery while the engine is running. Also, be sure all accessories are turned off.
Page 315 4RUNNER (1998) Type A Good Blown Type B Blown Good Type C Good Blown...
Page 316 4RUNNER (1998) If the headlights or other electrical If you cannot use one of the same components do not work, check the amperage, use one that is lower, but Type A fuses can be pulled out by fuses. If any of the fuses are blown, as close as possible to the rating.
Page 317 Add gain access to the bulbs. When re- system. Have your Toyota dealer cor- washer fluid. placing a bulb, make sure the ignition rect it as soon as possible.
Page 318 4RUNNER (1998) —Headlights Bulb Light bulbs Type 60/5 Headlight Parking and front side marker lights Front turn signal lights 1156 Rear turn signal lights Stop and tail lights 21/5 Back- up lights License plate light — High mounted stop light Interior light —...
Page 319 4RUNNER (1998) 1. Open the hood. Unplug the con- nector. Remove the rubber cover. If the connector is tight, wiggle it.
Page 320 Insert the connector. Make sure the rubber cover fits snug- ly on the connector and the headlight body. Aiming is not necessary after replac- ing the bulb. When aiming adjustment necessary, contact your Toyota dealer.
Page 321 4RUNNER (1998) Use a Phillips- head screwdriver.
Page 322 4RUNNER (1998)
Page 323 4RUNNER (1998) —Front turn signal lights Use a Phillips- head screwdriver.
Page 324 4RUNNER (1998) —Rear turn signal, stop an tail, and back- up lights Use a Phillips- head screwdriver.
Page 325 4RUNNER (1998) a: Back- up light —License plate lights b: Rear turn signal lights c: Stop and tail light Use a Phillips- head screwdriver...
Page 326 4RUNNER (1998)
Page 327 4RUNNER (1998) —High mounted stoplight Use a Phillips- head screwdriver...
Page 328 4RUNNER (1998)
Page 329 4RUNNER (1998) Part 7 DO- IT- YOURSELF MAINTENANCE— Chapter 7- 1 Introduction Engine compartment overview Fuse locations Do- it- yourself service precautions Parts and tools...
Page 330 4RUNNER (1998) Engine compartment overview "3RZ- FE engine 1. Windshield and back window washer fluid tank 2. Engine oil filler cap 3. Brake fluid reservoir 4. Fuse block 5. Battery 6. Engine coolant reservoir 7. Power steering fluid reser- voir 8.
Page 331 4RUNNER (1998) "5VZ- FE engine 1. Windshield and back window washer fluid tank 2. Power steering fluid reser- voir 3. Engine oil filler cap 4. Brake fluid reservoir 5. Fuse block 6. Battery 7. Engine coolant reservoir 8. Engine oil level dipstick...
Page 332 4RUNNER (1998) Fuse locations...
Page 333 4RUNNER (1998) Spare fuses...
Page 334 Read spark plug boots, etc.—will be separate Toyota Warranty statement hot. So be careful not to touch for details and suggestions. them. Oil, fluids spark This part gives instructions only for plugs may also be hot.
Page 335 4RUNNER (1998) NOTICE z Do not drive with the air clean- protection whenever er filter removed, or excessive you work on or under your ve- z Remember that battery and igni- engine wear could result. Also hicle where you may be ex- tion cables carry high currents backfiring could cause a fire in posed to flying or falling mate-...
Page 336 Checking power steering fluid Replacing light bulbs will need on performing do- it- yourself Parts (if level is low): Parts: maintenance. Remember Toyota Automatic transmission fluid Bulb with same number and watt- parts are designed in metric sizes, so DEXRONrII or III age rating as original (See charts your tools must be metric.
Page 337 4RUNNER (1998)
Page 338: Specifications
4RUNNER (1998) Part 8 Dimensions and weight SPECIFICATIONS " Dimensions and weight " Engine " Fuel " Service specifications " Tires " Fuses...
Page 339 4RUNNER (1998) Engine Fuel Service specifications Model: Fuel type: ENGINE 3RZ- FE and 5VZ- FE Unleaded gasoline, Octane Rating 87 Valve clearance (engine cold), mm (in.): Type: (Research Octane Number 91) or high- 3RZ- FE engine 3RZ- FE engine Intake 0 .
Page 340 4RUNNER (1998) Drive belt tension measured with Bor- Oil grade: roughs drive belt tension gauge No. API grade SH, ”Energy- Conserving II” BT- 33- 73F (used belt), Ibf: or SJ, ”Energy- Conserving” multi- 3RZ- FE engine grade engine oil or ILSAC multigrade Generator belt engine oil is recommended.
Page 341 4RUNNER (1998) COOLING SYSTEM Total capacity, L (qt., Imp. qt.): Coolant type: MANUAL TRANSMISSION 3RZ- FE engine With ethylene- glycol antifreeze Oil capacity, L (qt., Imp. qt.): With rear heater (Do not use alcohol type.) 3RZ- FE engine 11.0 (11.6, 9.7) Two- wheel drive models BATTERY Without rear heater...
Page 342 4RUNNER (1998) Fluid type: Automatic transmission fluid D- II or TRANSFER Oil type: DEXRONrIII (DEXRONrII) Hypoid gear oil API GL- 5 Oil capacity, L (qt., Imp. qt.): 1.0 (1.1, 0.9) Recommended oil viscosity: Oil type: Front Gear oil API GL- 4 or GL- 5 A.D.D.
Page 343 4RUNNER (1998) Tires BRAKES Tire pressure Minimum pedal clearance when de- kPa (kgf/cm or bar, psi) pressed with the pressure of 490 N (50 Tire size Wheel size kgf, 110 lbf) with the engine running, Front Rear mm (in.): 75 (2.9) 7J 1 6 P265/70R16 220 (2.2, 32)
Page 344 4RUNNER (1998) Fuses J80001 Engine compartment (U.S.A.) Fuses (type A) 1. PWR OUTLET 15 A: Power outlet 2. DEFOG 15 A: Back window defog- 3. STOP 10 A: Stop lights, high- mounted stoplight 4. ALT- S 7.5 A: Charging system 5.
Page 345 4RUNNER (1998) J80002 Engine compartment (Canada) 7. HORN 15 A: Horns, emergency flashers 8. DOME 15 A: Interior lights, person- lights, luggage compartment light, clock, car audio system 9. TAIL 10 A: Tail lights, parking lights, license plate lights 10. STA 7.5 A: Starting system 11.
Page 346 4RUNNER (1998) J80003 Instrument panel 27. IGN 7.5 A: SRS airbag system, multiport fuel injection system / se- 21. ECU- B 7.5 A: SRS airbag warning 14. HEAD(LH) 10 A: Left- hand head- quential multiport fuel injection sys- light light tem, discharge warning light 22.
Page 347 4RUNNER (1998) Fuses (type B) 28. HEATER 50 A: conditioning system, ”A.C” fuse 29. AM1 40 A: Starting system 30. AM2 30 A: Starting system, ”IGN” fuse 31. POWER 30 A: Power window, pow- er back window, electric moon roof Fuses (type C) 32.
Page 348 4RUNNER (1998)
Page 349 Administration U.S.Department of Transporta- (NHTSA) in addition to notifying tion. Washington.D.C. 20590. You UNIFORM TIRE Toyota Motor Sales, U.S.A., Inc. can also obtain other information QUALITY GRADING about motor vehicle safety from (Toll- free: 1- 800- 331- 4331). the Hotline.
Page 350 Toyota vehicles with information on surfaces of asphalt and concrete. A heat buildup and possible tire failure. uniform tire quality grading. tire marked C may have poor traction performance.

Toyota 4Runner 1998 Operating Manual

Chapter 1- 6 Ignition Switch, Transmission and Parking Brake

Chapter 7- 2 Engine and Chassis

Quick Links

Related Manuals for Toyota 4Runner 1998

Summary of Contents for Toyota 4Runner 1998

Page 1: And Controls

Page 31: Instruments And Controls

Page 145: Steering Wheel And Mirrors

Page 292: Maintenance And Care

Page 338: Specifications

Table of Contents