Frigidaire GLGR104FSS2 Operating Instructions

DRY TEMPERATURE
OPERATING INSTRUCTIONS
AUTO PERM PRESS/
END OF CYCLE PRESS SAVER START COLORS
PERM PRESS/COLORS KNITS/DELICATES
MEDIUM HEAT LOW HEAT ON OFF
REGULAR]WHITES _ AIR FLUFF
HIGH HEAT NO HEAT
YES NO
o
AUTO REGULAR]
WHITES
Before Operating Your Dryer
Readyour dryer Owner's Guide. it has important safety and
warranty information. It also has many suggestions for best drying
results.
To reduce the risk of fire, electric shock, or injury
to persons, read the IMPORTANT SAFETYINSTRUCTIONS in your
dryer owner's guide before operating this appliance.
Operating Steps
Read Drying Procedures in your Owner's Guide.
It explains these operating steps in detail.
1. Prepare items for drying.
2. Check that lint screen is dean and in place.
3, Load the dryer. If desired, add a dryer fabric
softener sheet.
4. Close the dryer door.
5. Set Dry Temperature control. Select PRESSSAVER if
desired.
6. Turn cycle selector clockwise to desired setting.
7, Start dryer, Pushthe Start button and hold for 1-2 seconds,
or turn the Turn to Start control clockwise to ON. Hold for 1-
2 seconds and release.
8. A signal will sound toward the end of the cool down
period when the End of Cycle Signal is ON.
9. Remove items immediately and hang or fold.
10. Clean lint screen after every load.
Temperature Selection
Always follow directions on fabric care labels.
To avoid fire hazard, do not use heat to dry items
containing feathers or down, foam rubber, plastics, or similarly
textured, rubber-like materials. Use Air Fluff-No Heat setting only.
TheREGULAR-HIGH HEA T, PERM PRESS-MEDIUM HEA T, and
KNITS/DELICATES-LOW HEAT temperature settings may be
used with any cyclesetting. TheAIRFLUFF-NOHEATsetting can
be used only in the Timed Dry cycle.
AIRFLUFF-NOHEATsetting tumblesthe load without heat. Use
Air Fluff to freshen clothing, pillows or blankets, or to dust
draperies.
Cycle Selection
Turn cycle selector clockwise to desired cycle and setting. Each
cycle endswith a cool down period. The heat automaticallyturns
off and the load continues to tumble during the cool down period.
This reduces wrinkling and makes items easier to handle during
unloading.
AUTO KNITS/
o
TIMED DRY 50 60 DEUCATES
Drying time varies depending on size and dampness of load,
weight and fabric type. Room temperature and humidity, type of
installation and electrical voltage or gas pressure can also affect
drying time.
Auto Regular Cycle
This cycle is best for cotton items. Drying time is determined
automatically at the temperature selection of your choice.
• High heat is suggested for cotton items.
• initially set cycle selector on NORMAL DRY,
• For items requiring more drying time, set cycle selector on
MORE,
For items requiring less drying time, set cycle selector on LESS.
Auto Delicate Cyde
This cycle is best for knit and delicate items. Drying time is
determined automatically at the temperature selection of your
choice.
Low heat is suggested for knit and delicate items.
initially set cycle selector on NORMAL DRY
For items requiring more drying time, set cycle selector on
MORE
For items requiring less drying time, set cycle selector on LESS.
• A signal will sound toward the end of the cool down
period when the Cycle Signal is ON.
If the Press Saver option isturned to YES,the cycle selector will
advance to the Press Saver setting. Unheated tumbling
continues during Press Saver for 16 minutes to help reduce
wrinkling if the dried load cannot be removed promptly. A
signal will sound briefly every five minutes as a reminder to
remove the load when the Cycle Signal is turned on.
Timed Dry Regular Cycle
This cycle provides approximately 60 minutes of drying time at the
temperature selection of your choice.
Auto Perm Press Cycle
This cycle is best for permanent press items. Drying time is
determined automatically at the temperature selection of your
choice.
Medium heat is suggested for permanent press
items.
Initially set cycle selector on NORMAL DRY,
For items requiring more drying time, set cycle selector on
MORE,
For items requiring less drying time, set cycle selector on LESS.
A signal will sound toward the end of the cool down period
when the Cycle Signal is ON.
P/N 137104000 (0806)