Remote Control Buttons = Stand By 0 - 9 = Direct Program I-II = Mono/Stereo - Dual I-II MENU = MENU = Programme Up (Cursor Up) = Cursor Right / Volume + TV = TV / Quit Menu (Red) = Sound Menu (Green) = Picture Menu F (Yellow)= Feature Menu (Blue)= Install Menu...
Control Panel Buttons Front AV input POWER / = Power On / Off VIDEO = VCR (yellow) = Volume - / Volume + AUDIO L / R = Audio left (white) / right (red) - P / P + = Program - / Program + MENU = Menu H-PHONE = Headphone 3,6 mm Ø...
Connect Peripheral Equipment There is a wide range of audio and video equipment that can be connected to your TV. The connection diagrams show the back of the TV where the different equipment should be connected. REAR PANEL CAMERA AUDIO HEADPHONE VIDEO DECODER...
Via the SCART connector Playback of NTSC recordings This TV can display video recordings played back in the Your TV set has two SCART connector sockets. This is NTSC 3.58 / 4.43 mode. for the connection of equipment which is fitted with a SCART socket e.g.
Preparation Place the TV on a solid surface. If placing the TV into a cabinet or alcove, ensure there is at least a 100mm (10cm) gap to the sides and rear and top of the TV. This is to allow for adequate ventilation during operation. Please read below for more safety informa- tion before installation.
Page 8
DON’T remove any fixed cover as this may expose dangerous voltages. DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has a stand-by mode. Switch off using the switch on the equipment and make sure your family know how to do this.
Page 9
7. Servicing Please refer all servicing to qualified personnel. Do not remove the back cover as this may result in an electric shock. 8. X-rays This television has sheilding for protection against the emission of X-rays. Warning! Any intervention contrary to regulations, in particular, any modification of high voltage or a replacement of the pic- ture tube may lead to an increased concentration of x-rays.
2- To switch on the TV from stand-by mode either: Before Switching on your TV Press a digit button on the remote control so that a pro- gramme number is selected, Power connection IMPORTANT: The TV set is designed to operate on Press Programme Up and Down buttons on the front of 220-240V AC, 50 Hz.
If you wish to check the stations press the " " button Entering Main Menu to move the red flashing number and name down to the • Press “MENU” button to enter main menu. In the programme you wish to view and press the red button main menu select submenu using “P +”...
There are two ways of entering the sound menu: Menu System • You can enter the Sound Menu directly by pressing the red “ ” button Your TV is provided with a menu system that simplifies the operation of the TV. Selecting the commands displayed on the screen con- •...
Setting Balance: Pressing “ “ or “ ” button will change the current sound mode. (e.g.: If the current sound mode is stereo, • Using “ “ or “ ” button select Balance. it will be stereo or visa versa). •...
Setting Contrast: Setting Black Stretch: • Using “ “ or “ ” button select Contrast. You can use this feature to switch black stretch on or off. Black Stretch enhances the black level of the picture. • Press “ ” button to increase contrast level. •...
Child Lock: You can use this feature to stop the controls on the front of the television being used. When the Child Lock is set to ON only the remote control will control the TV. • The Child Lock feature may be set to either On or Off. When Off is selected, there will be no difference in the operation of your TV.
• Then select and change the remaining letters and tuning mode of the program is stored as Channel when finished select STORE using the “ “ or “ ” Search Mode. buttons and store using the either of the “ “...
0.25 MHz steps using “ “ or “ ” buttons, you can • Press the GREEN BUTTON on the remote control select the 224.25MHz .When you type and select the this will insert the channel shown on the screen into frequency , the corresponding st a tion will be displayed.
• In the main menu select Install using the “ “ or “ ” buttons. • Open the Install menu by pressing either of the “ “ or “ ” buttons. (To open the Install Menu directly , do not enter the main menu just press the BLUE button located on the remote After APS is finalized, a rank list will appear on the control handset.)
• The selected page number will then be displayed in the top left corner of the screen and the page counter then searches until that page number is located. When located the page will be displayed. • Pressing the “ “...
• Press “ ” button to move the Teletext screen back- Tips ward one page at a time. For Fastext and Toptext Care of the Screen: The subject-heading for the information may have a The screen is best cleaned with a damp soft cloth. Using particular colour or can be in a form located in a an abrasive material or solvents will damage the sur- coloured box.