Clean/Replace Spark Plug; Clean Spark Arrester Screen; Air Cooling System; Carburetor Adjustment - Craftsman 580.325610 Operator's Manual

CJean_epJace Spark PJu9
Changethe spark piug every 100 hours of operation or once
each year, whichever comes first. This wifl help your engine
to start easier and run better.
1. Cleanarea around spark piug.
2. Remove and inspect spark piug.
3. Checkelectrode gap with wire feeler gauge and set
spark plug gap to 0.030 inch (0.76ram) if necessary.
2. Removefour screws that attachspark arrestor screen (C).
4. Replace spark plug if electrodes are pitted, burned or
porcelain is cracked. Use a recommended replacement
plug.
5. Install spark plug and tighten firmly.
NOTE:You can purchase a new spark plug by calling
l=800-4=MY=NONiE (469=4663),
Ctean Spark Attester Screen
The engine exhaust muffler has a spark arrestor screen.
Inspect and clean the screen every 100 hours of operation or
once eachyear, whichever comes first.
NOTE:You can purchase a new spark arrester screen by
calling 1-800-4-MY-HOME (469-4663).
If you useyour generator on any forest-covered, brush-
covered, or grass-covered unimproved iand, it must have a
spark arrestor. The spark arrestor must be maintained in good
condition by the owner/operator.
WARNING
_,_ Contact with muffler area can result in serious
burns.
Exhaust heat/gases can ignite combustibles,
structures or damagefuel tank causing a fire.
* DONOTtouchhot partsandAVODhot exhaust g ases.
, Allowequipment t o coolbeforetouching.
o Keepat least5 feet (1.5m) of clearance on all sidesof
generator i ncludingoverhead.
o Codeof Federa! Regulation (CFR)Title36 Parks,Forests, a nd
PublicProperty requireequipment p owered byan internal
combustion engine to havea sparkattester,maintained in
effective workingorder,complying to USDA Forestservice
standard 5100-1Cor laterrevision.Inthe Stateof California a
sparkarrester is required undersection4442 of theCalifornia
Publicresources code.Otherstatesmayhavesimilar laws.
Clean and inspect the spark arrestor as fellows:
1. To remove muffler heat shield (A) from muffler (B),
remove four screws that connectguard to muffler bracket.
3. Inspect screen and obtain a repiacement if torn,
perforated or otherwise damaged. DO NOT use a
defective screen, if screen is not damaged, clean it with
commercial soivent.
4. Reattach screen and muffler guard.
Air Cooling System
Overtime debris may accumulate in cyiinder cooiing fins and
cannot be observed without partial engine disassembly. For
this reason, we recommend you have a Sears or other
quaiified service deaier clean the cooiing system (A) per
recommended intervais (see Maintenance Schedub). Equally
important is to keeptop of engine free from debris=See
Generator C/eaning.
CarburetorAdjustment
The carburetor on this engine is iow emission, it is equipped
with a non-adjustable idle mixture valve and governed idJe,if
equipped. Governedidie and top speed have been set at the
factory, if adjustment is required, see any Sears or other
ualified dealer.
CAUTION
Excessively high operating speeds increase risk of injury
and damageto generator.
Excessively iow speeds impose a heavy ioad.
DONOTtamperwith governedspeed. G enerator s upplies
correctratedfrequency' andvoltagewhenrunningat governed
speed.
DONOTmodify' g enerator i n anyway'.
18