IMPORTANT SAFETY INFORMATION. READ ALL INSTRUCTIONS BEFORE USING. SAFETY PRECAUTIONS WARNING – WARNING – TO REDUCE THE RISK OF FIRE, TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY TO PERSONS, OBSERVE A RANGE TOP GREASE FIRE: THE FOLLOWING: A. Never leave surface units unattended at high A.
Page 3
INSTRUCTIONS DE SÉCURITÉ IMPORTANTES. LISEZ TOUTES LES INSTRUCTIONS AVANT D’UTILISER. PRÉCAUTIONS EN MATIÈRE DE SÉCURITÉ AVERTISSEMENT – AVERTISSEMENT – POUR RÉDUIRE LE POUR RÉDUIRE RISQUE D’INCENDIE, DE SECOUSSE ÉLECTRIQUE OU DE LE RISQUE D’UN FEU DE GRAISSE SUR LA SURFACE BLESSURE CORPORELLE, OBSERVEZ LES PRÉCAUTIONS DE CUISSON DE LA CUISINIÈRE : SUIVANTES :...
To replace: your dealer. Order genuine GE Slip the back edge of the filter part number WB02X8391. into the retaining tabs and push the front edge up until it snaps...
Pull down on the center of the front WB02X10700. Replacement filters edge of the filter. The filter will then can be ordered from your GE supplier. slip out of the retaining tabs on the back. If the hood is not vented to the...
An optional Power Cord Connection Kit, model total equivalent ductwork length using the approximate JXHC1, is available at extra cost from your GE feet of equivalent length of some typical ducts. supplier for installation using a standard 3-prong, grounded wall outlet.
Page 7
Installation Instructions WORKSHEET—CALCULATE TOTAL EQUIVALENT DUCTWORK LENGTH DUCT EQUIVALENT NUMBER DUCT EQUIVALENT NUMBER PIECES LENGTH x USED = TOTAL PIECES LENGTH x USED = TOTAL ″ x 10″ ⁄ 1 Ft. 6″ Round 53 Ft. Rect., wall cap (39 ft. w/o straight with damper)
Installation Instructions DAMAGE – SHIPMENT/INSTALLATION TOOLS YOU WILL NEED • If the unit is damaged in shipment, return the unit to the store in which it was bought for repair or replacement. • If the unit is damaged by the customer, repair or Flat blade and Phillips Pencil replacement is the responsibility of the customer.
Page 9
Installation Instructions CHOOSE VENT OPTION Determine the vent option that your installation will IMPORTANT: If the hood is to be installed in a require and that is available for your model from the recirculating, non-vented ductless manner, do not below choices. knock out any vent openings in the hood.
Page 10
Installation Instructions REMOVE WIRING COVER REMOVE EXHAUST ADAPTOR ″ x 10″ rectangular Remove the wiring cover from inside the hood. If exhausting/venting using the 3 ⁄ Set the cover and its mounting screw aside. duct—optional for JV338, JV347, JV348 and JV367 models only: Wiring Remove the exhaust adaptor from the inside of the...
Page 11
Installation Instructions ″ X 10″ RECTANGULAR FOR RECESSED-BOTTOM FOR 3 ⁄ CABINETS ONLY DUCTED DISCHARGE INSTALLATIONS ONLY: Attach exhaust adaptor/damper over the appropriate knockout opening (for vertical or horizontal, depending on installation) with two exhaust adaptor screws. Make sure damper pivot is nearest to top/back edge of hood.
Page 12
Installation Instructions MARK HOLES C. Outside rear exhaust ″ ″ Select the vent option that your installation will (Horizontal duct–3 ⁄ x 10 Rectangular) require and proceed to that section: • Use the diagram or the hood as a template and mark the locations on the cabinet for ductwork, A.
Page 13
KIT JXHC1 Mounting An optional Power Cord Connection Kit, model screw (4) JXHC1, is available at extra cost from your GE supplier for installation using a standard 3-prong, Keyhole (4) grounded wall outlet. Follow the Installation Instructions packed with the kit to connect the power cord to the range hood.
Page 14
Installation Instructions INSTALL LIGHT BULB REPLACE FILTER NOTE: A light bulb is not shipped with the hood. Make sure fan blade turns freely and replace the Obtain one locally. Purchase and install a type A15 filter. NOTE: Install the metal grease filter if ducted light bulb with an ordinary screw-base, not more or the charcoal filter if recirculated.
Page 15
This warranty is extended to the original purchaser and any succeeding owner for products purchased for home use within the USA. If the product is located in an area where service by a GE Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the product to an Authorized GE Service Location for service.
Contact Us ge.com If you are not satisfied with the service you receive from GE, contact us on our Website with all the details including your phone number, or write to: General Manager, Customer Relations GE Appliances, Appliance Park...