Product Identification; Safety; General Safety; Handling Safety - AEG GLASS-GLASS AS-M 3 Series Installation Manual

Icon Meaning
Note
Table 1: Icon meaning

1.2 Product Identification

Each module can be identified by means of the following
information:
Product Label
It is placed on the module backside. According to EN
50380 Directives it provides information about the main
parameters of the module: Product Type, Maximum
Power, Current at Maximum Power, Voltage at Maximum
power, Open Circuit Voltage, Short Circuit Current -as
measured under Standard Test Conditions, Maximum
System Voltage, Maximum Series Fuse etc. The product
label also features the Product Name Code (PNC).
MODULE TYPE:
Maximum Power (Pmax)
Power Sorting
MONOCRYSTALLINE Open Circuit Voltage (Voc)
Short Circuit Current (Isc)
PHOTOVOLTAIC MODULE
Maximum Power Voltage (Vmp)
WARNING
For field connection please use
Hazardous electricity can minimum Ø 4mm [12 AWG]
2
shock, burn or cause death. copper wires insulated
Do not touch connectors!
for a minimum temp. 90°C.
Figure 1: label example
Serial Number
Each individual module is identified by a unique serial
number univocally coupled with a barcode. Serial number
and barcode are permanently placed on the laminate,
under the front glass of the module, and are visible from
the module front.
Mounting holes
Connector (+)
Figure 2: Example of product technical drawings
AEG GLASS-GLASS MODULE INSTALLATION MANUAL
Instruction
Useful information for product
maintenance and operation is
provided
AS-M1202Z-BH(M6)-370/HV
Solar Solutions AG
Riedweg 3
6418 Rothenthurm, Switzerland
370 W Maximum Power Current (Imp) 10.91 A
info@aeg-solar.com
0 ~ 5 W Maximum System Voltage 1500 V
www.aeg-solar.com
Maximum Series Fuse A
41.72 V 25
Product assembled in P.R.C.
11.32 A Tolerance on Pmax ±3% / on Voc ±4% / on Isc ±4%
AEG is a registered trademark used
33.95 V Electrical Protection Class: Class II
under license from AB Electrolux (publ).
Measured at Tested according to:
IEC 61730-1:2016 /
Standard Test Conditions EN IEC 61730-1:2018 + AC:2018;
IEC / EN 61215-1:2016; IEC / EN 61215-1-1:2016;
(E=1000 W/m 2 , Tc=25°C, IEC 61215-2:2016 / IEC 61730-2:2016 /
AM=1.5)
EN 61215-2:2017 + AC:2017 + AC:2018; EN IEC 61730-2:2018 + AC:2018.
Grounding holes
Frame (Section)
Drainage holes
Mounting holes
Connector (-)
Please refer to the specific product datasheet on
www.aeg-solar.com for the latest technical data.

2. SAFETY

2.1 General safety

All AEG PV modules should be installed according to
all local and national applicable standards, codes and
regulations. Only qualified personnel should install
the solar modules. Installers bear the risk of all injury
that might occur during installation including, without
limitation, the risk of electric shock. Check and follow
all safety precautions specified even for the other
components of the system.
Look for any visible damage to the package or the
product itself. Double-check the order information and
the product nameplate to ensure the products are of
the ordered type. Should you find any problems, contact
the shipping company and / or your supplier as soon as
possible before attempting product installation.

2.2 Handling safety

Please observe the below indications when handling AEG
solar modules:
Store the pallets in a ventilated, dry location until
installation. Do not open the module boxes during
storage or transportation. Inappropriate transport and
installation may void the warranty.
Do not apply paint or adhesive to module top
surface.
Do not use mirrors or other magnifiers to
artificially concentrate sunlight on the modules.
Do not expose back sheet foils directly to sunlight.
Do not attempt to disassemble the modules
Do not remove any attached nameplates or components
Do not exceed the maximum stapling limitation of 2
pallets (standard packaging for shipment).
After unpacking, the modules should be laid horizontally.
Do not incline or stack the modules.
Do not pile up modules without protections to prevent
scratches to the glass and frame. Should the modules
need to be piled, they need to be separated by special
paper or plastic angles.
Do not scratch or damage the module surface.
3
EN GD202311 V1-23