Sealey CV040 Manual

Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions,
and properly maintained, give you years of trouble free performance.
IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE
THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR
PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to Wear eye
instruction protection
manual
1. SAFETY
WARNING! Ensure Health and Safety, local authority and general workshop practice regulations are adhered to when using tools.
‰
Maintain the tool components in good and clean condition for best and safest performance.
9
Ensure that a vehicle which has been jacked up is adequately supported with axle stands.
9
Wear approved eye protection. A full range of personal safety equipment is available from your Sealey stockist.
9
Wear suitable clothing to avoid snagging. DO NOT wear jewellery and tie back long hair.
9
Keep children and other unauthorised persons away from the working area.
9
Ensure there is adequate lighting prior to using the tool.
9
DO NOT use the kit if any parts are missing or damaged.
8
DO NOT use tool for any purpose other than that for which it is designed.
8
IMPORTANT: These instructions are intended as a guide only. Always
refer to the vehicle manufacturer's service instructions or a proprietary
manual to establish the current procedure.
2. INTRODUCTION
Designed for the installation and removal of slotted bushes on
commercial spring suspension. Includes a 12 Tonne hydraulic cylinder
(supplied without hydraulic pump). Use in conjunction with Hydraulic
Pump Model No's RE83/840/CWH (Air/Hydraulic) or RE97.10-01
(Hydraulic). Installation protects the bush using the parallel working
tension elements. Suitable for use on the vehicle. Safe and easy-to-use.
3. CONTENTS/APPLICATIONS
Part Number Description
CV040.02 Bush dia. 105mm (Marked No. 3)
CV040.03 Bush dia. 105mm (Marked No. 4)
CV040.04 Bush dia. 66mm (Marked No. 5) stored under 12
CV040.05 Bush dia. 59mm (Marked No. 6)
CV040.06 Bush dia. 49mm (Marked No. 7)
CV040.07 Bush dia. 78mm (Marked No. 12)
CV040.08 Bush dia. 78mm (Marked No. 13)
CV040.09 Bush dia. 98mm (Marked No. 14)
CV040.10 Clamping Ring dia. 68mm (Marked No. 9)
CV040.11 Clamping Ring dia. 60mm (Marked No. 10)
CV040.12 Clamping Ring dia. 51mm (Marked No. 11)
CV040.13 Installation Pad dia. 108mm (Marked No. 15)
CV040.14 Installation Pad dia. 103mm (Marked No. 16)
CV040.15 Installation Pad dia. 108mm (Marked No. 17)
CV040.16 Threaded Stud 'Short' M16x2.0
CV040.17 Threaded Stud 'Long' M16x2.0
CV040.18 Clamp Sleeve Set
CV040.19 Hydraulic Ram
CV040.20 Washer (Set of 4)
© Jack Sealey Limited
HYDRAULIC BUSH TOOL - COMMERCIAL
CV040
MODEL NO:
Original Language Version
Application
MAN (410/414/460) Renault (430/450/460)
Volvo FM12
MAN (410/414/460)
Renault (430/450/460)
Volvo FM12
Volvo FM12
Renault (430/450/460)
MAN (410/414/460)
MAN (410/414/460)
Renault (430/450/460)
Volvo FM12
Volvo FM12
Renault (430/450/460)
MAN (410/414/460)
CV040 Issue 2 (H,2,F) 16/06/23