X84; Id List - Kenwood KDS-100 Technical Document

4. KDS-100 Configuration
You cannot enter a decimal value or a number that is
out of range.
You can adjust the configuration when the "GPS
Function" checkbox is selected.
・ Base ID
This checkbox allows you to set the ID number of the
base unit that receives GPS data from each KDS-100.
You can enter a value from 1000 and 4999. You cannot
enter a decimal value or a number that is out of range.
You can adjust the configuration when the "GPS
Function" checkbox is selected.
・ GPS Report Mode
This checkbox allows you to select the GPS data
transmission format of the KDS-100.
Auto: Send GPS data automatically at a certain
time interval.
Poll: Send GPS data when the KDS-100 receives
a request from the base.
You can adjust the configuration when the "GPS
Function" checkbox is selected.
・ GPS Report Interval
You can send GPS data automatically with a certain
time interval by selecting "Auto" for "GPS Report
Mode". This mode allows you to set the time interval.
You can set the time interval from 1 to 3600 seconds,
in steps of 1 second, by pressing the ∧ ∧ ∧ ∧ and ∨ ∨ ∨ ∨ keys on
the right of the display. You can enter the value directly,
but you cannot enter a decimal value or a number that
is out of range.
You can adjust the configuration when the "GPS
Function" checkbox is selected.
・ GPS Time Mark
The GPS data transmission may collide with the
transmission to the base if the GPS data is sent
frequently. This function allows you to configure the
KDS-100 so that this collision will not occur.
Set the delay time of the GPS data transmission at the
GPS Time Mark by setting the GPS Time Mark in the
KDS-100. Each KDS-100 that performs a GPS data
transmission should have a different delay time.
Set the time interval from 0 to the time set for the "GPS
Report Interval", in steps of 1 second, by pressing the ∧ ∧ ∧ ∧
and ∨ ∨ ∨ ∨ keys on the right of the display. You can enter
the value directly, but you cannot enter a decimal value
or a number that is out of range.
You can adjust the configuration when the "GPS
Function" checkbox is selected.
28
T T T T ID List
This command allows you to configure the KDS-100
transmission operation. The following window
appears when executing the command from the
Menu.
Use "Fleet" and "ID" to identify the recipient in
FleetSync. You can configure the recipient as either
the individual or the group.
Chart description
Fleet: The "Fleet" line sets the fleet number. You
directly enter a Fleet number from 100 and 349,
but you cannot enter a decimal value or a
number that is out of range.
You can enter "0" or "A" in the "Fleet" cell to
configure the recipient with only an "ID". In this
case, "All" appears. ALL also appears if you do
not enter a "Fleet", after entering an "ID".
ID: The ID line sets the ID number. You can
enter an ID number from 1000 and 4999, but you
cannot enter a decimal value or a number that is
out of range.
You can enter "0" or "A" in the "ID" cell to
configure the recipient with only a "Fleet". In this
case, "All" appears. ALL also appears if you do
not enter an "ID", after entering an "Fleet".
ID Name: Use "Fleet" and "ID" to identify the
recipient in FleetSync. You can input the name of
the recipient in the "ID name" cell.
Enter the characters allocated to each recipient,
in the cell.
You can enter a maximum of 38 characters.
Following is a list of the available characters:
(space) ! " # $ % & ' ( ) * + , -. / 0 1 2 3 4 5 6 7 8
9 : ; < = > ? @ [ \ ] ^ _ ` A B C D E F G H I J K L
M N O P Q R S T U V W X Y Z a b c d e f g h i j k
l m n o p q r s t u v w x y z.
The ID Name is used to identify the sender of a
message and the recipient. When receiving a
message from a sender whose information is not
in the terminal's memory, the sender's "Fleet"
and "ID" number appear.
TX Inhibit (Status/Sel. Call): This column
allows you to configure the KDS-100 display.
When selecting "YES", the recipient will not be
displayed on the KDS-100. Therefore you cannot
select the recipient from Menu mode or Status
List mode. If you select "NO", the status call will
be displayed on the KDS-100.