Husqvarna AUTOMOWER 420 Operator's Manual page 32

Note:
®
Automower Connect is always connected to
your product while the mobile device have connection
with the mobile network and the product is switched on.
Note:
All countries do not support Automower
Connect because of regional specified cellular systems.
The included Automower
applies if there is a third part sub-supplier of 2G/3G/4G
available in the operational area. In some countries
®
Bluetooth is not available because of legal reasons.
To enable the GeoFence function
GeoFence is a GPS-based theft protection that makes a
virtual fence for the product. You will get a message if
the product is moved on the other side of the GeoFence.
1. Put the product in the center of the work area.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 23 .
3. Use the arrow buttons and the OK button to
move through the menu structure
> Automower Connect > GeoFence > Activate
GeoFence .
4. Push the OK button.
Activate GeoFence and push the OK
5. Select
button.
To set a new center point for the Geofence function
1. Put the product in the center of the work area.
To get access to the menu in the
2. Do steps 1–3 in
display of the product on page 23 .
3. Use the arrow buttons and the OK button to
move through the menu structure
Automower Connect > GeoFence > New center
point .
4. Push the OK button.
To set the GeoFence level of sensitivity
The higher level of GeoFence sensitivity, the easier the
alarm starts.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to
move through the menu structure
Automower Connect > GeoFence .
3. Use the arrow buttons to select level of GeoFence
sensitivity.
4. Push the BACK button.
To use the SMS function
The SMS function sends you an SMS when the product
is moved out of the GeoFence.
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
32 - Product settings
®
®
Connect life-time service only
Accessories
Accessories >
Accessories >
2. Use the arrow buttons and the OK button to
move through the menu structure
> Automower Connect > Communication > Use
SMS .
3. Push the OK button.
4. Use the arrow buttons and the OK button to
move through the menu structure
Automower Connect > Communication > SMS
phone numbers .
5. Push the number buttons to enter the telephone
number with country code. For example
(+)46701234567.
6. Push the BACK button.
Note:
There is a maximum of 10 SMS each month
from the product.
Network
APN settings
The product must specify APN settings to be able to
use and send data via the mobile net. Settings for
Husqvarna SIM is default.
4.2.10.3 Ultrasonic Automower
Ultrasonic function makes the product decrease
The
speed when the product comes near an obstacle. The
product operates at a lower speed if the
function is disabled.
To set the Ultrasonic function
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to
move through the menu structure
Ultrasonic > Use .
4.2.10.4 Headlights
To set the schedule for the headlights
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to
move through the menu structure
Headlights > Schedule .
Always ON , Evening only
3. Select between
Evening & night (19:00-07:00) or
(19:00-00:00),
Always OFF .
To set the Flashes when fault function
The headlights flashes if the product stops to operate
Flashes when fault is enabled.
because of a fault if
To get access to the menu in the
1. Do steps 1–3 in
display of the product on page 23 .
2. Use the arrow buttons and the OK button to
move through the menu structure
Headlights > Flashes when fault .
3. Use the OK button to enable or disable the
Flashes when fault function.
Accessories
Accessories >
®
450X
Ultrasonic
Accessories >
Accessories >
Accessories >
1201 - 007 - 20.02.2023