Page 1
ACC/ARTM-7221/FC Installation Guide 6806800E98A March 2008...
Page 2
Emerson reserves the right to revise this document and to make changes from time to time in the content hereof without obligation of Emerson to notify any person of such revision or changes.
Intelligent Platform Management Controller IPMI Intelligent Platform Management Interface Light Emitting Diode Linear Feet per Minute PICMG PCI Industrial Computer Manufacturers Group PCI Mezzanine Card Read-Only Memory Twisted Pair Ethernet Transmit Data Universal Serial Bus Elektromagnetische Vertraeglichkeit ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 10
File > Exit Notation for selecting a submenu <text> Notation for variables and keys [text] Notation for software buttons to click on the screen and parameter description Repeated item for example node 1, node 2, ..., node 12 ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 11
LED description; renamed RTM name to ACC/ARTM- 7221/FC; added power requirements and critical temperature spots 223454 April 2006 Update for final release 223454 April 2006 Update on installation procedure 6806800E9 March 2008 Update document to Emerson style (logo, copyright, etc.) ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 12
Mail comments to us by filling out the following online form: http://www.emersonnetworkpowerembeddedcomputing.com/ > Contact Us > Online Form In "Area of Interest" select "Technical Documentation". Be sure to include the title, part number, and revision of the manual and tell us how you used it. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
The RTM has been tested in a standard Emerson system and found to comply with the limits for a Class A digital device in this system, pursuant to part 15 of the FCC Rules, EN 55022 Class A respectively.
Page 14
LED is permanently ON. RTM Damage Installing the RTM with other blades than the PENT/ATCA-7221 damages the RTM. Only install the RTM with the Emerson PENT/ATCA-7221 blade. Operation RTM damage High humidity and condensation on the RTM surface causes short circuits.
Page 15
Laser Some variants of the RTM are a Class I laser product. The use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Anwendungen in der Telekommunikationsindustrie und im Zusammenhang mit Industriesteuerungen verwendet werden. Installation, Wartung und Betrieb dürfen nur von durch Emerson ausgebildetem oder im Bereich Elektronik oder Elektrotechnik qualifiziertem Personal durchgeführt werden. Die in diesem Handbuch enthaltenen Informationen dienen ausschließlich dazu, das Wissen von Fachpersonal zu ergänzen, können es aber in keinem Fall ersetzen.
Page 18
Beschädigung des RTMs Wenn Sie das RTM nicht zusammen mit dem PENT/ATCA-7221 Front Blade installieren, wird das RTM beschädigt. Installieren Sie das RTM deshalb nur zusammen mit dem Emerson PENT/ATCA-7221 Front Blade. Datenverlust Wenn Sie das RTM aus einem eingeschaltetem System herausziehen während die blaue LED auf dem Front Blade noch blinkt, gehen Daten verloren.
Page 19
Einige Varianten des Produktes sind Laserprodukte der Klasse I. Um nicht schädlicher Laserstrahlung ausgesetzt zu werden, beachten Sie die folgenden Hinweise: Anpassungen am Produkt, die Bedienung von Steuerelementen sowie die Durchführung von Prozeduren dürfen nur gemäß den Anweisungen in diesem Dokument erfolgen. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
We welcome and appreciate your comments on our documentation. We want to know what you think about our manuals and how we can make them better. Mail comments to: Emerson Network Power - Embedded Computing GmbH Lilienthalstraße 15 85579 Neubiberg Germany Email: reader-comments@mcg.mot.com...
Introduction Features Features The ACC/ARTM-7221/FC is a rear transition module (RTM) which provides easy access to I/O signals of the Emerson PENT/ATCA-7221 front blade. The I/O signals are available via the zone 3 connectors. The ACC/ARTM-7221/FC provides the following: System management/IPMI –...
63 4.3.2. The test consisted of dropping the RTM from 100mm height. As a result of the test, some locating pins were damaged which fix the two alignment blocks that are required by the PICMG 3.0 specification. Due to the damage, the alignment blocks were allowed to rotate slightly. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Weight of RTM 0.7 kg Ordering Information As of the time of writing this guide, the following RTM variant was available. Consult your local sales representative for a more-up-to-date list. Order Number Variant name 121914 ACC/ARTM-7221/FC ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 26
Introduction Ordering Information ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Action Plan - Part 1 Start Installation Inspect delivered package items Make sure requirements are met Hard disk to be connected or to be installed? Connect/install hard disk IPMB1 device to be connected? Connect IPMB1 device ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 28
Is slot powered? Switch on system power Switch off slot power Install RTM Install RTM Install RTM Cables to face plate connectors necessary? Connect cables to face plate connectors Switch on slot power Installation finished ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Before installing the RTM, make sure the requirements described in this section are met. 2.2.2.1 Power Requirements The RTM draws approximately 5W from the front blade it is connected to to. 2.2.2.2 Backplane Requirements For installing the RTM, you need a system without a zone 3 midplane. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Temp. Change +/- 0.25ºC/min according to +/- 0.25ºC/min NEBS Standard GR-63- CORE Rel. Humidity 5% to 95% non-condensing 5% to 95% non-condensing according to Emerson- according to Emerson- internal environmental requirements internal environmental requirements ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 31
0.5 mm amplitude 1g 1 mm amplitude 2.0 g 5-20 Hz 20-250 Hz Shock 5 g/11 ms halfsine 15 g/11 ms half sine according to Emerson-internal according to Emerson- environmental requirements internal environmental requirements Free Fall 1,200 mm/all edges and corners To guarantee proper RTM operation, you have to make sure that the temperature at the following location is not exceeded.
IPMB1 interface of the ATCA-7221. The following figure shows the location of the IPMB1 connector. Figure 2-4 Location of IPMB1 Connector IPMB1 Connector The following figure shows the pinout of the IPMB1 connector. Figure 2-5 IPMB1 Connector Pinout IPMB1_SDA IPMB1_SCL ACC/ARTM-7221/FC Installation Guide (6806800E98A)
ACC/ATCA-7221/HDD/SATA for the RTM. For further information refer to the ACC/ATCA-7221/HDD/SATA Installation Guide which can be downloaded from the Emerson literature catalog. Figure 2-6 Location of Serial ATA Connector for On-Board Hard Disks...
Installation SATA for On-board Hard Disks The following figure shows the connector pinout. Figure 2-7 Serial ATA for On-Board Hard Disk Connector Pinout SATA0_TX+ SATA0_TX- SATA0_RX- SATA0_RX+ 3.3V 3.3V 3.3V ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Figure 2-8 Location of Serial ATA Connector for External Hard-Disks SATA Connector for external hard disks The following figure shows the connector pinout. Figure 2-9 Serial ATA for External Hard Disks Connector Pinout SATA_TX_P SATA_TX_M SATA_RX_M SATA_RX_P ACC/ARTM-7221/FC Installation Guide (6806800E98A)
The RTM can be installed into a powered or nonpowered system and must be installed into a AdvancedTCA system without a zone 3 midplane. RTM Damage Installing the RTM with other blades than the PENT/ATCA-7221 damages the RTM. Only install the RTM with the Emerson PENT/ATCA-7221 blade. 2.4.1 Nonpowered System Damage of Circuits Electrostatic discharge and incorrect RTM installation and removal can damage circuits or shorten their life.
The blue LED on the front blade starts to flash while the front blade powers down. 3. Wait until the blue LED on the front blade is ON 4. Ensure that the top and the bottom handles of the RTM are in outward position ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 38
7. Insert the front blade from the system's front into the same slot as the RTM 8. Close the handles of the front blade The blue LED on the front blade starts flashing during the power-up procedure. 9. Tighten the two face plate screws on the front blade ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 39
RTM Malfunctioning Incorrect RTM installation and removal can result in RTM malfunctioning. When plugging the RTM in or removing it, do not press on the face plate but use the handles. 6. Remove the RTM from slot ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Installation Face Plate Controls, Indicators and Connectors Face Plate Controls, Indicators and Connectors The following figure shows the face plate of the RTM. Figure 2-10 Face Plate ACC/ARTM-7221/FC Installation Guide (6806800E98A)
COM or connecting a serial device to a RJ-45 connector labeled as E1/T1 may damage the telephone or the RTM. Therefore, only connect E1/T1 networks to RJ-45 connectors labeled as E1/T1 ports and only connect serial devices to RJ-45 connectors labeled as COM. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
PS/2 keyboard and mouse simultaneously. The following connector pinout gives information on which signal is assigned to which pin. Figure 2-14 Keyboard/Mouse Connector Pinout Keyboard data Mouse data VP5_KBD Keyboard clock Mouse clock ACC/ARTM-7221/FC Installation Guide (6806800E98A)
The following connector pinout gives information on which signal is assigned to which pin. The "x" stands for the number of the interface. Figure 2-15 E1/T1 Connector Pinout RX+_x RX-_x n.c. TX+_x TX-_x n.c. n.c. n.c. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Installation LEDs 2.5.2 LEDs The following figure highlights the LEDs available at the RTM's face plate. . Figure 2-16 Face Plate LEDs Face Pate LEDs ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Page 45
OFF: RTM is active and cannot be removed The status of all LEDs can be determined via the PICMG 3.0 command "Get FRU LED State". The status of the LEDs can be changed via the PICMG 3.0 command "Set FRU LED State". ACC/ARTM-7221/FC Installation Guide (6806800E98A)
The RTM's MMC and the front blade's IPMC are not reset via this key. Zone 3 Connectors The RTM provides two zone 3 connectors: P30 and P31. They provide interfaces to: Serial (RS-232) Serial ATA Fiber channels Keyboard/Mouse IPMI ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Intelligent Platform Management Standard V1.5 Rev. 1.1. It is connected to the front blade's IPMC via IPMB1. Emerson offers a Monta Vista Linux Carrier Edition 3.1 (MVL CGE 3.1) driver for the IPMC of the front blade and the MMC of the RTM.
Location of IPMI sensor ARTM-7221 Temp. For further details about IPMI sensors as well as supported IPMI commands, refer to the ACC/ARTM-7221/FC: Control via IPMI Programmer's Guide which can be downloaded from the Emerson literature catalog. ACC/ARTM-7221/FC Installation Guide (6806800E98A)
Documents The Emerson Network Power - Embedded Computing publications listed below are referenced in this manual. You can obtain electronic copies of Emerson Network Power - Embedded Computing publications by contacting your local Emerson sales office. For documentation of final released (GA) products, you can also visit the following website: http://www.emersonnetworkpowerembeddedcomputing.com...
Page 52
Related Documentation Emerson Network Power - Embedded Computing Documents ACC/ARTM-7221/FC Installation Guide (6806800E98A)
For on-board hard disk LEDs Standard compliances Reset key Serial interface connector USB connector Temperatures Critical hot spots Non-operating I2C address of IDROM Operating IDROM I2C address Installation Into nonpowered systems Zone 3 connectors Into powered systems ACC/ARTM-7221/FC Installation Guide (6806800E98A)