Panasonic YD-500GP5 Operating Instructions Manual page 22

○
Jog-dial
4
voltage display
○
5
7-segment LED
setting
" voltage "
" arc length "
" arc
○
6
characteristics "
" penetration
control "
function select
○
Jog-dial
7
Names and functions
● When Mode selection key ○
key ○
selects different options, please adjust corrosponding set value according
3
different items.
・During welding, " Welding " current can be adjusted. However " initial " and
" crater " current can NOT be changed.
● When Mode selection key ○
detailed description.
● When Mode selection key ○
・ It does not function.. ( When" Call " is selected, only Jog-dial
work. )
● When Mode selection key ○
・It does not function.. (When " Call " is selected, only Jog-dial
work. )
● When Mode selection key ○
・On stand-by status, ○
6
・During welding, it shows the voltage value of the actual output.
● When Mode selection key ○
・It shows specific set values.
● When Mode selection key ○
・Use Jog-dial ○
to select channel number. LED shows corresponding channel
7
number. If the welding parameters are avilable in the channel, the channel can be
selected, else the corresponding channel can NOT be selected. When the channel
stored with data is selected, the channel and parameters are displayed alternately
and welding can start.
● When Mode selection key ○
・By turning the Jog-dial ○
setting current and voltage. The flashing means welding parameters to be stored.
・Press selection key ○
12
parameters are recorded in the channel being selected.
● When a self-diagnosable error occurs, ( For troubleshooting:
・It shows alarm signal number.
● When "voltage"/ "arc length " function is selected, the setting method of the
corrosponding selection number is decided by P11 of "F. Adj" function menu.
When P11 is 0, it is adjusted by wire feeder potentiometer; when P11 is 1, it can
be changed by Jog-dial ○
● When" arc characteristics " function is selected, the value can be changed by Jog-
dial ○
7
● When"penetration control " function is selected, the value can be changed by Jog-
dial ○
7
Note: To change"penetration control ", welding method ○
"Deepen ".
● When Mode selection key ○
・When key ○
selects different options, please adjust corrosponding set value
6
according different items.
・During welding, the contents in ○
current change not be changed.
● When Mode selection key ○
・Refer to detailed description.
● When Mode selection key ○
・select Call channel number. (Only the channel number being recorded in
shown. )
● When Mode selection key ○
・Record channel number is select.
is set to " Weld ", (refer to description in ○
12
is set to "F. Adj",(
12
is set to " Call ",
12
is set to " Record ",
12
is set to " Weld ",
12
data of the item being selected is shown.
is set to "F. Adj", (
12
is set to " Call ",(
12
is set to " Record ", (
12
, channel number can be selected. LED shows "CH"
7
to return to " Weld " from " Record " and the corresponding
7
is set to" Weld ", (please refer to the description in
12
can be adjusted. However, " initial " and " crater "
8
is set to "F. Adj", (
12
is set to " Call ",
12
is set to " Record ",
12
18
)・ when
3
Section 5.4) ・ refer to
○ , key ○
7 8
○ , key ○
7 8
Section 5.4)
Section 5.6)
Section 5.6)
Section 13.1)
is to be selected as
14
Section 5.4)
○
5
, ○ , ○
10 12
, ○ , ○
10 12
○
)
6
can be