1. Manuals
  2. Brands
  3. Nokia Manuals
  4. Cell Phone
  5. RH-37 Series
  6. Service software and tuning instructions

Nokia RH-37 Series Service Software And Tuning Instructions

Transceivers
Hide thumbs Also See for RH-37 Series:
Table of Contents

Advertisement

Quick Links

Download this manual
Nokia Customer Care
RH-37 Series Transceivers
3 - Service Software and Tuning
Instructions
 2004 Nokia Corporation
Issue 1 07/04
Page 1
Company Confidential

Advertisement

Table of Contents
loading

Related Manuals for Nokia RH-37 Series

Summary of Contents for Nokia RH-37 Series

  • Page 1 Nokia Customer Care RH-37 Series Transceivers 3 - Service Software and Tuning Instructions  2004 Nokia Corporation Issue 1 07/04 Page 1 Company Confidential...
  • Page 2 RH-37 Service Software and Tuning Instructions Nokia Customer Care [This page left intentionally blank] Nokia Corporation Page 2 Issue 1 07/04...

  • Page 3: Table Of Contents

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Table of Contents Page No Quick Guide for Phoenix Service SW Installation ................5 Phoenix Installation Steps in Brief ..................... 5 Phoenix Service SW ..........................7 Before installation ..........................7 Installing Phoenix ..........................8 Updating Phoenix installation ......................12...
  • Page 4 RH-37 Service Software and Tuning Instructions Nokia Customer Care [This page left intentionally blank] Nokia Corporation Page 4 Issue 1 07/04...

  • Page 5: Quick Guide For Phoenix Service Sw Installation

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Quick Guide for Phoenix Service SW Installation Phoenix Installation Steps in Brief DCT-4 generation Test and Service Software is called “Phoenix”. These are the basic steps to install Phoenix: • Connect a DK2 Dongle or FLS-4S POS Flash Device.
  • Page 6 RH-37 Service Software and Tuning Instructions Nokia Customer Care The Phoenix Service Software installation contains: • service software support for all phone models included in the package • flash update package files for FPS-8* and FLS-4S programming devices • all needed drivers for:...

  • Page 7: Phoenix Service Sw

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Phoenix Service SW Before installation • Check that a dongle is attached to the parallel port of your computer . • Download the installation package (e.g. phoenix_service_sw_a12_2003_50_6_35.exe) to your computer (e.g. C:\TEMP).

  • Page 8: Installing Phoenix

    RH-37 Service Software and Tuning Instructions Nokia Customer Care Installing Phoenix Run the phoenix_service_sw_a12_2003_50_6_35.exe to start the installation. Install Shield will prepare. To continue, click "Next" in the Welcome dialog. Choose the destination folder, it is recommended to use the default folder C:\Program- Files\Nokia\Phoenix.
  • Page 9 RH-37 Nokia Customer Care Service Software and Tuning Instructions Choose “Next” to continue. You may choose another location by selecting “Browse” (not recommended). Setup copies the components, progress of the setup is shown. Please wait… Drivers are installed and updated, please wait. The process may take several minutes to complete.
  • Page 10 RH-37 Service Software and Tuning Instructions Nokia Customer Care If the operating system does not require rebooting (Windows 2000, XP), the PC com- ponents are registered straight away. Nokia Corporation Page 10 Issue 1 07/04...
  • Page 11 RH-37 Nokia Customer Care Service Software and Tuning Instructions Click "Finish" to finalize. Phoenix is ready for use. If the operating system used requires restarting your computer (Windows 98, SE, ME), the Install Shield Wizard notifies you about it. Select "Yes..." to reboot the PC immedi- ately and "No..."...

  • Page 12: Updating Phoenix Installation

    RH-37 Service Software and Tuning Instructions Nokia Customer Care Now the installation of Phoenix Service SW is ready and it can be used after: • installing phone model specific Phone Data Package for Phoenix • configuring users and connections FLS-4S can be used right away.

  • Page 13: Uninstalling Phoenix

    RH-37 Nokia Customer Care Service Software and Tuning Instructions a11_2003_41_5_28) the installation will be interrupted. Please always follow the instructions on the screen. Uninstalling Phoenix Uninstallation can be done manually from Windows Control Panel - Add / Remove Pro- grams.
  • Page 14 RH-37 Service Software and Tuning Instructions Nokia Customer Care Progress of the uninstallation is shown. If the operating system does not require rebooting, select “Finish” to complete. If the operating system requires rebooting, Install Shield Wizard notifies you about it.

  • Page 15: Repair

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Repair If you experience any problems with the service software or suspect that files have been lost, you can use the repair function before completely reinstalling Phoenix. Note that the original installation package (e.g. phoenix_service_sw_a12_2003_50_6_35.exe) must be found on your PC when you run the repair setup.
  • Page 16 RH-37 Service Software and Tuning Instructions Nokia Customer Care Phoenix reinstalls the required components and registers them, the procedure is the same as in the update installation. To complete, choose “Finish” . Nokia Corporation Page 16 Issue 1 07/04...

  • Page 17: Data Package For Phoenix (Product Specific)

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Data Package for Phoenix (Product Specific) Before installation Product Data Package contains all product specific data to make the Phoenix Service Software and tools usable with a certain phone model. Check that the dongle is attached to the parallel port of your computer.
  • Page 18 RH-37 Service Software and Tuning Instructions Nokia Customer Care To continue, choose “Next”. In this view, you can see the contents of the data package. Read the text carefully. There should be information about the Phoenix version needed with this data package.
  • Page 19 RH-37 Nokia Customer Care Service Software and Tuning Instructions Phoenix application is installed and the directory is shown. Choose “Next” to continue. To start copying the files, choose “Next”.. Nokia Corporation Issue 1 07/04 Page 19...
  • Page 20 RH-37 Service Software and Tuning Instructions Nokia Customer Care Phone model specific files are installed. Please wait. To complete installation, choose “Finish”. You now have all phone model specific files installed in your Phoenix service SW. Nokia Corporation Page 20...

  • Page 21: Uninstalling The Data Package

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Now Phoenix can be used to for example flash phones and print type labels after: • configuring users • managing connections FLS-4S can be used right away. FPS-8* can be used after updating flash update package files to it .
  • Page 22 RH-37 Service Software and Tuning Instructions Nokia Customer Care Once the previously installed data package is uninstalled, choose “Finish”. Run the RH-37_dp_v_0.00_mcuA0.00.0.exe again in case you want to continue installa- tion from the beginning. Nokia Corporation Page 22 Issue 1 07/04...

  • Page 23: Configuring Users

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Configuring Users Start Phoenix Service SW and Login. To add new user, choose “Edit”. If user ID is already configured, choose your own user ID from the list and choose “OK”.
  • Page 24 RH-37 Service Software and Tuning Instructions Nokia Customer Care Type in your name and initials in the fields and choose “OK”. User has now been created, choose “OK”. You are now able to login with this username, choose “OK”. Nokia Corporation...

  • Page 25: Managing Connections

    RH-37 Nokia Customer Care Service Software and Tuning Instructions Managing Connections Start Phoenix service SW and login. Choose “Manage Connections” from the “File” menu. In this dialog, you can select, edit, delete existing connections and create new ones. You can create a connection either manually or by using a Connection Wizard.
  • Page 26 RH-37 Service Software and Tuning Instructions Nokia Customer Care In the next dialogs, you are asked to select some settings for the connection. Manual settings A) For FLS-4S POS Flash Device choose following connection settings • Media: FBUS • COM Port: Virtual COM Port used by FLS-4. Please check this always!
  • Page 27 RH-37 Nokia Customer Care Service Software and Tuning Instructions If you use the Wizard, connect the tools and a phone to your PC and the wizard will automatically try to configure the correct connection. Activate the connection you want to use by clicking it. Use up/down arrows to move it on top of the list.
  • Page 28 RH-37 Service Software and Tuning Instructions Nokia Customer Care When a product is found, Phoenix loads product support and when everything is ready, name of the loaded product support module and its version are shown at the bottom of the screen.

  • Page 29: Updating Flash Support Files For Fps-8* And Fls-4

    If you are not using a separate installation package, you can skip this section. Start by double clicking flash_update_03_07_000.exe. The installation begins. If the same version of the flash update package already exists, and you want to reinstall Copyright Nokia. All rights reserved. Issue 1 07/04 Page 29...
  • Page 30 It is highly recommended to install the files to the default destination folder C:\Program Files\Nokia\Phoenix. To continue, choose “Next” . Note! When installing the flash update files for the first time you may choose another location by selecting “Browse” (not recommended). Copyright Nokia. All rights reserved. Page 30 Issue 1 07/04...
  • Page 31 RH-37 Nokia Customer Care Service Software and Tuning Instructions The installation continues. To complete the procedure, choose “Finish”. FLS-4 can be used right after the flash update package is installed. Copyright Nokia. All rights reserved. Issue 1 07/04 Page 31...

  • Page 32: Updating Fps-8* Flash Prommer Sw

    Select ”FPS-8 maintenance” from the ”Flashing” menu. When a new FPS-8 flash update package is installed to your computer, you are asked to update the files to your FPS-8 Prommer. Copyright Nokia. All rights reserved. Page 32 Issue 1 07/04...
  • Page 33 The update procedure takes a couple of minutes, please wait until you are notified that the update has been successful. Choose “OK” and close “FPS8 Maintenance” UI. View after a successful prommer software update. Copyright Nokia. All rights reserved. Issue 1 07/04 Page 33...
  • Page 34 Nokia Customer Care FPS-8 sw can also be updated by pressing the ”Update” button and selecting the appro- priate fps8upd.ini file under C:\Program Files\Nokia\Phoenix\Flash. All files can be loaded separately to FPS-8. To do this, just press the right mouse button in the ”Flash box files”...

  • Page 35: Activating And Deactivating Fps-8

    First, fill in the “FPS-8 activation request” sheet in the FPS-8 sales package and follow the instructions in the sheet. When the activation file is received (e.g. 00000.in), copy it to C:\Program- Files\Nokia\Phoenix\BoxActivation directory on your computer. (This directory is created when Phoenix is installed.) Start Phoenix Service Software.

  • Page 36: Deactivating Fps-8

    Select ”FPS-8 maintenance” from ”Flashing” menu as when activating prommer or updating sw. Select “Deactivate” from the “FPS8 Maintenance” UI. Confirm Deactivation by choosing “Yes”, Box will be deactivated. To complete deactivation, turn FPS-8 power off and on. Copyright Nokia. All rights reserved. Page 36 Issue 1 07/04...

  • Page 37: Jbv-1 Docking Station Sw

    Note: DO NOT CONNECT THE USB CABLE / JBV-1 TO YOUR COMPUTER YET! Run Jbv1_18_update.zip file and start SW Installation by double clicking Setup.exe. Files needed for the JBV-1 Package setup program will be extracted. Copyright Nokia. All rights reserved. Issue 1 07/04 Page 37...
  • Page 38 Nokia Customer Care The installation begins, please read the information displayed. To continue, choose “Next” . Use suggested destination folder where JBV-1 SW package is installed and choose “Next” to continue. Copyright Nokia. All rights reserved. Page 38 Issue 1 07/04...
  • Page 39 Nokia Customer Care Service Software and Tuning Instructions To continue, select “Full” Installation and choose “Next” . The program folder is created. To continue, choose “Next”. Software files are installed. Copyright Nokia. All rights reserved. Issue 1 07/04 Page 39...
  • Page 40 After you have installed or updated the JBV-1 USB driver, the actual JBV-1 SW update can begin. Go to folder C:\Program Files\Nokia\JBV-1 Firmware Update\JBV-1 Firmware Update and start JBV-1 Update SW by double clicking fwup.exe. The JBV-1 Firmware update starts and shows the current status of the JBV-1 connected.
  • Page 41 The older sw file JBV1v17.CDE is visible in this view only if the previous JBV-1 SW pack- age has been installed on your computer. After a successful update and after choosing “OK” the current JBV-1 status is displayed. Copyright Nokia. All rights reserved. Issue 1 07/04 Page 41...
  • Page 42 Choose “Refresh Status” to see the current SW version and then “Update Firmware” to update the SW. After you have updated all docking stations, close the “JBV-1 Firmware Update” dialog. Copyright Nokia. All rights reserved. Page 42 Issue 1 07/04...

  • Page 43: Baseband Calibration

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Baseband Calibration If the UEMEK or the Combo memory has been changed, the baseband has to be cali- brated. It is only the UEMEK that has to be calibrated for baseband.
  • Page 44 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Figure 1: Selecting energy management calibration with Phoenix. Select “Calibrate” and save the results by pressing “Save To Phone” when the calibration is finished. Figure 2: Starting calibration using Phoenix Check that the values are within the limits given in table below.

  • Page 45: Calibration Limits

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Calibration limits Table 1: BB calibration limits Parameter ADC Offset ADC Gain 26500 28500 BSI Gain 1100 Battery Voltage Offset 2300 2900 Battery Voltage Gain 10000 11000 Charger Voltage 55800 64000...

  • Page 46: Phoenix Tuning

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Phoenix Tuning General instructions for tuning Connect the phone to a PC, which has Phoenix Service Software and a dongle installed, using either • repair jig and DAU-9S (RS232) cable or •...

  • Page 47: Semi-Automatic Calibrations And Measurements - Step By Step: Rx/Tx And Gsm Bands

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Table 2: List of necessary tunings after replacement of RF key components and surrounding R/C/Ls Tunings/ Calibrations Antenna Z7800 Switch Module Z7802 SAW 1800 Rx Z7801 SAW 1900 Rx RF ASIC N7500 (Helgo 8.5)
  • Page 48 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care For an error free initial synchronization, the 26 MHz frequency of the reference oscillator must be accurate enough. Therefore, the previously calibrated AFC value is written to the DA converter and the corresponding AFC voltage tunes the VCTCXO to the correct fre- quency.
  • Page 49 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions The setup should now look like this: The results must fulfill the following limits: Calibration value / Test case Typical Low limit High limit AFC value / check AFC_VALUE [DAC] -350...

  • Page 50: Rx Band Filter Response Compensation

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Otherwise continue Rx calibration according to the tuning steps 2 and 3 for GSM1800 respectively GSM1900 bands. Note the limits of the calibration mentioned in the list above. Pop up window for Rx calibration of GSM1800 band Calibration fails and possible reasons: •...
  • Page 51 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions If a radio communication tester (CMD 55, CMU 200, HP 8960, MT 8801) is used, assure that <continuous mode> is switched on and <modulation> switched off. Compensate for external RF cable and test jig losses.
  • Page 52 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Tune the band filters and save its compensation values to the phone memory for each GSM band as described above. Automatic tuning A faster and more comfortable method for Band Filter Calibration (BFC) can be per- formed by the automatic tuning mode.
  • Page 53 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions (The example below shows a screen shot in GSM900!) Press OK for tuning. The new tuning values are highlighted in the column <Measured Level Difference (dB)>. Note the limits as specified in the table below.

  • Page 54: Rx Channel Select Filter Calibration

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Channel Number Limits (as indicated in the < Rx Band Filter Response Compensation > (of < Measured Level window) Difference >) Meas. point GSM900 GSM1800 GSM1900 High First -6.0 dB +2.0 dB -3.0 dB...

  • Page 55: Tx Power Level Tuning

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions The notch value might not be displayed in later Phoenix versions. Press Tune and the optimal values are found. Press Stop, the values are saved to the phone and the calibration has finished.
  • Page 56 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Note: TX Power Tuning must be done with a peak power meter, e.g. Anritsu model ML2408A with Anritsu Peak Power Sensor MA2442A and a suitable attenuator. The use of the built-in power meter of GSM testers is likely to cause larger errors than the use of a dedicated power meter and might cause miss tuning so that the phone might be not compliant with the GSM specifications.
  • Page 57 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Tx power level tuning GSM900 in GMSK mode Tuning of GSM850 and GSM900 work in the same manner, only band settings are differ- ent. Set the operating mode to local mode.
  • Page 58 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Adjust DAC Values for all power levels according to the target values: TX PA Mode Power level Target power (dBm) High 32.5 Base level The power levels may differ from the target power levels mentioned in Phoenix.
  • Page 59 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Check if all levels match the target values, correct if necessary and then press <Save&Continue>. Note: For Phones with RFMD power amplifier also the EDGE power level 7 needs to be tuned. The window (like shown above) will pop up accordingly.
  • Page 60 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Adjust DAC Values for all power levels according to the target values: Power level Power (dBm) Base level The power levels may differ from the target levels mentioned. Make sure that the output power for Power Level 0 is equal or lower than 1dB below the saturation output power.
  • Page 61 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Tx power level tuning GSM1800 & GSM1900 in EDGE mode On the popped up window, press ok. The setup should now look like this: Nokia Corporation Issue 1 07/04 Page 61...

  • Page 62: Tx Iq Tuning

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care Adjust DAC Values for all power levels according to the target values. Check if all levels match the target values, correct if necessary and then press < Save & Continue >.
  • Page 63 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Select RF Controls Operation Mode Burst RX/TX Channel TX Data Type All1 TX Power Level The setup should now look like this: Note: Dependent on the Phoenix version also VBAT value is not displayed The power levels during TxIQ are adjusted automatically.
  • Page 64 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care If a spectrum analyzer is used, make the following settings. GSM900 Center Frequency 897.4 MHz Frequency Span 300 kHz Resolution Bandwidth 3kHz Video Bandwidth 3kHz Sweep Time 100 msec. Sweep Type...
  • Page 65 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Use the variables 'TX I DC offset' and 'TX Q DC offset' to adjust the carrier signal to a minimum level (marker 2). Tuning can be performed by using arrow keys on the keyboard.
  • Page 66 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care The spectrum analyzer now shows a plot like this: Marker 1 [T1] 3 kHz RF Att 30 dB Ref Lvl Ref Lvl 25.61 dBm 3 kHz Mixer -20 dBm 35 dBm 35 dBm 897.33229000 MHz...

  • Page 67: Fully Automatic Calibration, Tuning & Measurement By Phoenix

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Here you can see an example: Fully automatic calibration, tuning & measurement by Phoenix <Auto-Tune> Auto-tune is designed to align the phone' s RF part easier and faster, it calibrates, tunes, measures the following: •...

  • Page 68: Preparations For Phoenix

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care • Usage of XRF-1 cable • Usage of the jig MJ-22 There is no need to adjust any value, since all values are correctly pre-defined in the proper file delivered with the install-packages Preparations for Phoenix Follow the instructions as described in chapter General instructions for tuning.
  • Page 69 RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Edit the column <Loss/dB>. Note: Jig and product are pre-defined. GPIB interface The GPIB card shall be labeled by National Instruments or at least compatible with their products. Drivers must be installed and card <accepted> by Phoenix. The following procedure has to be made once for <acceptance>...

  • Page 70: Automatic Tuning Procedure

    RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care The set up should now look like this: Automatic tuning procedure Select Tuning Alt-U Auto-Tune Alt-A Tune Alt-T The <Auto-Tune> results are displayed as follows: The result values are logged in a result-file, if initiated according to the following chap- ter.

  • Page 71: Phone Book Downloading

    RH-37 Nokia Custome Care Service Sofftware and Tuning Instructions Log file To enable the creation of a log file for saving the calibration, tuning and measurement results Select Tuning Alt-U Auto-Tune Alt-A Auto-Tune options Alt-O Press the button <Enable/Disable logging> ON and select the path of the result file.
  • Page 72 RH-37 Service Sofftware and Tuning Instructions Nokia Custome Care [This page left intentionally blank] Nokia Corporation Page 72 Issue 1 07/04...

Table of Contents