Page 1
Form No. 3403-967 Rev A Road Light Kit including Brake Lights LT-F3000 Series Traction Unit Model No. 02918—Serial No. 316000001 and Up Installation Instructions This product complies with all relevant European directives. For details, please see the Declaration of Incorporation (DOI) at the back of this publication.
Procedure Description Qty. Left bracket Right bracket Light frame assembly Headlamp Headlamp cable Washer (M8) Washer (5/16 inch) Install the front lights Locknut (M8) Hex-head screw (M8 x 25 mm) Front light connector Washer (M12) Locknut (M12) Hex-head screw (M12) Light switch Hazard switch Install the switches.
Page 3
Installing the Rear Lights Parts needed for this procedure: Bolt (M16 x 110 mm) Locknut (M16) Left light bracket assembly Right light bracket assembly Number-plate bracket Number plate light Figure 1 Washer (M6) Locknut (M6) Hex-head screw (M6 x 20 mm) 4.
Page 4
Installing the Fuses and the Number Note: If a beacon kit is fitted to the machine, you may still use the pivot bolt location. Plate 9. Feed all electrical cables down the front of the ROPS WARNING frame and onto the electrical mount panel. 10.
Page 5
2. Drill an 8 mm (5/16 inch) diameter hole on the center of the bulkhead, 15 mm (5/8 inch) from the center line of the bulkhead (Figure Figure 7 1. Hex-head screw (M6) 4. Number-plate bracket 2. Washer (M6) 5. Locknut (M6) 3.
Page 6
Installing the Front Lights Parts needed for this procedure: Left bracket Figure 9 Right bracket 1. Black wire 2. Red wire Light frame assembly Headlamp 8. Connect the number plate light to the connector leads. Refer to Figure Headlamp cable 9.
Page 7
Connecting the Wires locknuts (M8), and 4 hex-head screws (M8 x 25 mm) as shown in Figure 1. Connect a headlamp cable to the left headlamp by passing the end with just the pins through the hole in the headlamp body from the inside so that the connector is inside the lamp (Figure 14).
Figure 16 View on cable entry 1. Black 3. Green 2. Red/white 4. Blue Figure 17 Figure 18 1. Front marker light — black 3. Headlamp — black wire 1. Screw 3. Control pod wire (top), red/white wire (top), blue wire (bottom) (bottom) 2.
5. On the rear face of the control pod, above the key switch, remove the switch blank panels between the auto limited lift and beacon switches (Figure 20). Completing the Installation Parts needed for this procedure: Adhesive reflector Cable tie Serial label Procedure 1.
(rear) and white (front) marker lights will turn on. Replace all worn or damaged parts with genuine Toro parts. Adjusting the Headlights Check that all lights are working on a regular basis. Ensure that the headlights are adjusted correctly.
Page 14
The method of transmission shall be electronic transmittal. This machinery shall not be put into service until incorporated into approved Toro models as indicated on the associated Declaration of Conformity and in accordance with all instructions, whereby it can be declared in conformity with all relevant Directives.
Page 15
The Way Toro Uses Information Toro may use your personal information to process warranty claims, to contact you in the event of a product recall and for any other purpose which we tell you about. Toro may share your information with Toro's affiliates, dealers or other business partners in connection with any of these activities. We will not sell your personal information to any other company.
Page 16
Countries Other than the United States or Canada Customers should contact their Toro Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the Toro importer. If all other remedies fail, you may contact us at Toro Warranty Company.