Related Manuals for Hitachi EH-TP504
Summary of Contents for Hitachi EH-TP504
- Page 1 Cover p age HITACHI OPETATOR INTERFACES EH-HMI EH-TP500 Series OPERATING INSTRUCTIONS Basic User’s Manual for EH-TP500 Series Touchscreen Products Hitachi Europe GmbH EH-TP500 Series OPERATING INSTRUCTIONS Ver. 1.00...
- Page 2 Copyright © 2016 Hitachi Europe GmbH – Dusseldorf, Germany Subject to change without notice The information contained in this document is provided for informational purposes only. While efforts were made to verify the accuracy of the information contained in this documentation, it is provided “as is” without warranty of any kind.
-
Page 3: Table Of Contents
Table of Contents Table of Contents Introduction ..........................4 Safety Guide ........................... 5 Product Overview ......................6 Standards and Approvals ....................7 Technical Specifications ....................8 Technical Data ......................10 4.1. Dimensions ....................... 13 4.2. Installation Environment .................... 15 4.3. Installation Procedure .................... -
Page 4: Introduction
This Operating Instruction describes the main features of EH-TP500 Series operator panels. The Manual refers to the following models: Operator interface with TFT color 4.3” display touchscreen EH-TP504 Operator interface with TFT color 7” widescreen display touchscreen EH-TP507 Operator interface with TFT color 10.4” display touchscreen EH-TP510 Operator interface with TFT color 13.3”... -
Page 5: Safety Guide
Safety Guide Safety Guide The manual contains safety standards that must be respected for the personal safety and to avoid damage. Indications of attention are divided into three levels of severity: DANGER: indicates a failure to observe safety rules and such failure may cause death or serious injuries. DANGER ATTENTION: indicates a failure to observe safety rules and that deficiency may cause damage. -
Page 6: Product Overview
Product Overview 1. Product Overview The Hitachi EH-TP500 Series HMI products combine state-of-the-art features and top performance with an outstanding design. They are the ideal choice for all demanding HMI applications including factory and building automation. The EH-TP500 Series HMI panels have been designed to run the HiMobile software. -
Page 7: Standards And Approvals
The product may be identified through a plate attached to the rear cover. You will have to know the type of unit you are using for correct usage of the information contained in the guide. An example of this plate is shown in the figure below: EH-TP504 product model name ETOP504H4P1... -
Page 8: Technical Specifications
3V 50mAh Lithium, rechargeable, not user- replaceable, model VL2330. Fuse Automatic Serial Port RS-232, RS-485, RS-422 software configurable User memory Flash 128MB for EH-TP504, 507 Flash 256MB for EH-TP510, 513, 515 Recipe memory Flash Hardware clock Clock/Calendar with back-up battery Accuracy RTC (at 25°C) <100ppm... - Page 9 Technical Specifications Electromagnetic Compatibility (EMC) Radiated disturbance test Class A EN 55011 Electrostatic discharge immunity test 8 kV (air electrostatic discharge) EN 61000-4-2 4 kV (contact electrostatic discharge) Radiated, radio-frequency, 80 MHz ÷ 1 GHz, 10V/m EN 61000-4-3 electromagnetic field immunity test 1,4 GHz ÷...
-
Page 10: Technical Data
Technical Data 4. Technical Data Model EH-TP504 EH-TP507 Display / Backlight TFT Color / LED TFT Color / LED Colors Resolution 480X272 800X480 4.3” 7” widescreen Diagonal (inches) Dimming User memory flash 128MB 128MB SD card slot Yes. Flash memory storage Yes. - Page 11 Technical Data Model EH-TP510 EH-TP513 Display / Backlight TFT Color / LED TFT Color / LED Colors Resolution 800X600 1280X800 10.4” 13.3” widescreen Diagonal (inches) Dimming User memory lash 256MB 256MB SD card slot Yes. Flash memory storage Yes. Flash memory storage Recipe memory limited only by available memory limited only by available memory...
- Page 12 Technical Data Model EH-TP515 Display / Backlight TFT Color / LED Colors Resolution 1024X768 15” Diagonal (inches) Dimming User memory lash 256MB SD card slot Yes. Flash memory storage Recipe memory limited only by available memory RS-232,RS-485, RS-422 DB9 Serial Port female software configurable 2 10/100 Mbit with integrated Ethernet port...
-
Page 13: Dimensions
Technical Data 4.1. Dimensions Cut out MODEL 149mm/5.86” 109mm/4.29” 136mm/5.35” 96mm/3.78” 56mm/2.40” 4mm/0.16” EH-TP504 EH-TP500 Series Operating Instructions VER 1.00... - Page 14 Technical Data Cut out MODEL 187mm/7.36” 147mm/5.79” 176mm/6.90” 136mm/5.35” 47mm/1.85” 4mm/0.16” EH-TP507 287mm/11.3” 232mm/9.13” 276mm/10.86” 221mm/8.70” 56mm/2.20” 4mm/0.16” EH-TP510 336mm/13.22” 267mm/10.51” 326mm/12.83” 256mm/10.07” 56mm/2.20” 4mm/0.16” EH-TP513 392mm/15.43” 307mm/12.08” 381mm/15” 296mm/11.65” 60mm/2.36” 4mm/0.16” EH-TP515 EH-TP500 Series Operating Instructions VER 1.00...
-
Page 15: Installation Environment
thickness of the case where is mounted the equipment: from 1,5mm to 6mm max surface roughness where the gasket is applied: O120 um Applying the gasket The gasket should be applied on the rear of the frame. Fig. 4.1: EH-TP504, EH-TP507 Fig. 4.2: EH-TP510, EH-TP513, EH-TP515 A. Gasket B. Installation cut-out... -
Page 16: Installation Procedure
Technical Data 4.3. Installation Procedure Place the fixing brackets as shown in figure (Fig. 4.3). Fig. 4.3 CAUTION Screw each fixing screw until the bezel corner gets in contact with the panel. EH-TP500 Series Operating Instructions VER 1.00... -
Page 17: Connections
Connections 5. Connections EH-TP504 Fig. 5.1 1. Serial Port 2. 2x Ethernet Port 3. USB Port 4. Power Supply 5. Expansion slot for Plugin module 6. SD Card Slot EH-TP500 Series Operating Instructions VER 1.00... - Page 18 Connections EH-TP5xx Fig. 5.2 1. Serial Port 2. 2x Ethernet Port 3. USB Port (version 2.0 - 1.1) 4. USB Port (version 2.0 High speed only) 5. Power Supply 6. 2x Expansion slot for Plugin module 7. SD Card Slot EH-TP500 Series Operating Instructions VER 1.00...
-
Page 19: Serial Port
Connections 5.1. Serial Port The serial port is used to communicate with the PLC or with another type of controller. Different electrical standards are available for the signals in the PLC port connector: RS-232, RS-422 and RS-485. The serial port is software programmable. Make sure you select the appropriate interface in the programming software. -
Page 20: Ethernet Port
Connections 5.2. Ethernet Port The Ethernet port has two status indicators. Please see description in figure. OFF: Valid link has NOT been detected ON: No activity BLINKING: Activity ON: Valid link has been detected EH-TP500 Series Operating Instructions VER 1.00... -
Page 21: Optional Plugin Module
Connections 5.3. Optional plugin module EH-TP500 Series panels have several optional plugin module, multiple modules configurations are possible. Slot#2 and Slot#4 are available only if plugin module has the “bus extension connector”. Each slot carries three communication channels: • 1 serial interface •... - Page 22 Connections Below you can find relation between modules and max number of modules that can be used into EH-TP500 Series panels, based on their Interface Type: Module Application Max Modules Interface Type Bus Extension connector EH-TPICNE 1 for EH-TP50x 2 for EH-TP51x EH-TPICN 1 for EH-TP50x 2 for EH-TP51x...
-
Page 23: Power Supply, Grounding And Shielding
Power Supply, Grounding and Shielding 6. Power Supply, Grounding and Shielding The power supply terminal block is shown in the figure below. Fig. 6.1 Note: Ensure that the power supply has enough power capacity for the operation of the equipment. The unit must always be grounded to earth. -
Page 24: Battery
Charge: At first installation must be charged for 48 hours. When the battery is fully charged, it ensures a period of 3 months of data back-up at 25°C. Battery Fig. 7.1: EH-TP504 Battery Fig. 7.2: EH-TP507, EH-TP510, EH-TP513, EH-TP515 ATTENTION Dispose of batteries according to local regulations. -
Page 25: Cleaning Faceplates
Cleaning Faceplates / Getting Started 8. Cleaning Faceplates The equipment must be cleaned only with a soft cloth and neutral soap product. Do not use solvents. 9. Getting Started EH-TP500 Series HMI products must be programmed with the software HiMobile Studio. HiMobile Studio is a software tool that must be properly installed on a computer running Microsoft Windows. -
Page 26: System Settings
System Settings 10. System Settings EH-TP500 Series HMI products have a system settings tool to allow configuration of system options. The user interface of System Settings tool is based on a rotating menu. Use navigation buttons Next/ Back to scroll through the available options. The active item is highlighted on the left side. - Page 27 System Settings Activation of Systems Settings System Mode: If HiMobile runtime is not running: Press “System Settings” button Normal operation on the HMI screen. If HiMobile runtime is running: recall context menu, select “System Settings” Select the Restart option then choose the “Configuration OS” option. Note: To recall the context menu click and hold any unused area of the touchscreen for a few seconds.
- Page 28 System Settings Resize Image Area reserved to authorized technical personnel Download Configuration OS update the Configuration OS module of BSP Download Main OS update the Main OS module of BSP Download Splash Image replace the splash screen image displayed by the device at power- up;...
-
Page 29: Led Indicator On Front Panel
LED Indicator on Front Panel / Unpacking and Packing Instructions 11. LED Indicator on Front Panel The table below shows the symbol of the LED indicator dedicated to special functions. LED Indicator Status Meaning Symbol Color Hardware fault / Battery low Normal operation Green BLINK... - Page 30 Hitachi Europe GmbH Am Seestern 18 Tel: +49 (0) 211 52 83-0 D-40547 Düsseldorf, Germany Fax: +49 (0) 211 52 83-649 http://www.hitachi-ds.com/...