COLOR TELEVISION RECEIVER Chassis : SCT57B Model: CK564BZR1X/BWT CK567BSR1X/BWT CK565BSR1X/VWT CK567BSR1X/VWT CK565BST1X/BWT CK568BST1X/BWT CK566BSR1X/BWT CK566BST1X/VWT COLOR TELEVISION RECEIVER CONTENTS Precautions Specifications and IC Data Disassembly and Reassembly Alignment and Adjustment Troubleshooting Exploded View and Parts List Electric Parts List Block Diagram...
0.5 milliamp. Reverse the Heed the high voltage limits. These include power-plug prongs in the AC outlet and the XÐray Protection Specifications Label, and repeat the test. the Product Safety and X-ray Warning Note on the service data schematic. Samsung Electronics...
Page 4
14. Components, parts and wiring that shock, fire or other hazards. appear to have overheated or that are otherwise damaged should be replaced with parts that meet the original specifications. Always determine the cause of damage or overheating, and correct any potential hazards. Samsung Electronics...
Page 5
9. Minimize body motions when handling These can generate electrical charges that unpackaged replacement ESDs. Motions damage ESDs. such as brushing clothes together, or lifting a foot from a carpeted floor can generate enough static electricity to damage an ESD. Samsung Electronics...
Disassembly and reassembly 3. Disassembly and Reassembly 3-1 Back Cover Removal 1. After removing the 9 screws, pull the cabinet backwards. Samsung Electronics...
Page 11
Disassembly and reassembly 3-2 Speaker Removal 1. Loosen the 4 screws and remove the holder - speakers. Samsung Electronics...
Page 12
Disassembly and reassembly 3-3 CRT Removal 1. Spread a soft mat on the floor. Place the TV set face down. 2. Remove the 4 screws mounting the CRT to the front cabinet. 3. Lift the CRT. Samsung Electronics...
Adjustment Mode adjustment parameters are listed in the is cancelled). accompanying table. Select them by pressing the CHANNEL keys ( , ). 7. Cancel the Adjustment Mode by re-pressing the "Factory" or "Power on" keys. Samsung Electronics...
Page 16
"HIDDEN" key . Even if the TV power is cut off, the Aging Mode is not cancelled, The patterns are displayed at 5 sec intervals. The AGING mode is cancelled by repressing the "HIDDEN" key. Samsung Electronics...
Page 17
CHANNELS (SYSTEM DOES NOT REQUIRED MATTER) B/G & D/K & M 1) HIGH FOR XA/XB (ALWAYS) : CRYSTAL 3.58MHz/4.43MHz CONSTANT OTHER 2) AUDIO MUTE DURING NO SIGNAL (ALWAYS) 3) SET THE CONTRAST TO 90 IN THE STANDARD PICTURE Samsung Electronics...
Page 18
NICAM ERROR CHECK BIT AFT-ON AFT - OFF INDIA ONLY TDA8375 TDA8844 RF AUDIO OUT MUTE OFF RF AUDIO OUT MUTE ON D/K STEREO F = 6.752 D/K STEREO F = 6.25' CLOCK DISPLAY OFF CLOCK DISPLAY ON SZM-199EV ONLY Samsung Electronics...
Page 19
→ → → → → CS 2 AUTO SECAM NT4.43 NT3.58 AUTO SECAM NT4.43 NT3.58 4-2-6 RESET The Reset Mode is used during factory inspection. Function Reset: Channels Add/Erase Sort Language Basic (English) System Auto (Non-TTX micom only) Samsung Electronics...
Page 20
The degaussing coil operates for about 1 second to a distance of about 6 feet before removing after the power is switched ON. If the set has power. been moved or turned in a different direction, disconnect its AC power for at least 10 minutes. Samsung Electronics...
Page 21
3. Use the P mode key (on the remote control) for the STANDARD picture. 12. Tighten the deflection yoke. 4. Adjust the Screen VR (on the FBT) so that the voltage (See Fig.4-1.) on the oscilloscope becomes 130 + 2.5V. 130V 2.5Vp-p H-Blanking Fig. 4-1 Samsung Electronics...
Page 22
1. Set SCT to 50 fL in the Factory Service Mode using CA100. (See Fig. 4-4 ) Fig. 4-4 (c) Low-Light Adjustment 1. Set SBT to 1.2 fL in the Factory Service Mode using CA100. (See Fig. 4-4 Samsung Electronics...
Page 23
5. Ensure "SD On" (Signal Input) and "SD Off" (No Signal). C-BUS IC201 IC902 TUNER (TDA8844) 6. Adjust T201 (connected to TDA8844 pins3,4) IF (38.9MHz) so that AFA Bit is "INSIDE WINDOW" (the AFB Bit is 1). Fig. 4-6 4-10 Samsung Electronics...
Page 24
3. Adjust with PVS (starts blinking) exactly at middle of the screen. 4. Adjustment with PVA : Top and Bottom margins of the picture are 4. 5. Adjustment with PSL : Bottom of picture to bottom of screen. 6. Adjust PHS horizontally. Center the picture. Samsung Electronics 4-11...
5-1 No Video (Raster On, No Sound) Measure the Check/Replace Voltage of each of, 8 pins TU101, HC101 of TU101 Check IC901 Check/Replace Pins 39, 40 IC901, IC202 See "No Sound" See "No Video" (Video OK) (Sound OK) Samsung Electronics...