LG WD-20900 Owner's Manual

Cleaning and Maintenance Electrical connection
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric
1. Do not use an extension cord or double adapter.
shock.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualified
person to prevent danger.
Cleaning the water inlet filter
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualified personnel. Repairs carried out by inex-
perienced persons may cause injury or serious malfunctioning. Contact your local service centre.
1 2 3 4 5 • Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may
burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing
machine standing at room temperature for a few hours before putting it into operation.
Turn off the Unscrew the Pull out the water Clean the filter Refit the inlet
water tap water inlet hose inlet filter using a hard filter and tighten
bristle brush up the inlet hose CAUTION
Cleaning the drain pump filter The hose supplied with the machine must be used.
Old hoses may not be reused.
CAUTION
1 2 3 4 5
• The appliance is not intended for use by young children or infirm persons without supervision.
• Young Children should be supervised to ensure that they do not play with appliance.
Open the lower Unplug the drain Remove any After cleaning, refit Close the lower
filter cover and hose plug. Then extraneous the drain filter cap cover
pull out the drain open the filter by matter from the and tighten it by
hose. turning to the left pump filter turning it clockwise. Installation of drain hose
insert the drain plug
Cleaning the dispenser drawer
ca. 100 cm
5 Once you
have finished ca. 145 cm
1 2 3 4 cleaning, replace
the drawer and
run a rinse cycle
ca. 105 cm
without laundry or
Pull out the Clean the dispenser Clean inside the Insert the dis-
soap.
dispenser drawer drawer under recess with an penser drawer
flowing water old toothbrush
Hose
Retainer
Cleaning in general
Important: Do not use methylated spirits, solvents or similar products.
Tie
strap
Exterior Interior
Proper care of your washing machine can extend its service life. Dry around the washing machine door
max. 100 cm
The outside of the machine can be cleaned with warm water and opening, flexible gasket and door glass.
min. 60 cm
a neutral non-abrasive household detergent. Immediately wipe Run washing machine through a complete
• The drain hose should not be placed higher than 100 cm above the floor.
off any spillage. Wipe with damp cloth. Avoid striking the surface cycle using hot water. Repeat process if
with sharp objects. Never hose down the machine! necessary. • Proper securing of the drain hose will protect the floor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause abnormal
noise and cause the machine to malfunction and leak.
Safety instructions for use
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating instruc-
tions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these operating
instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appli-
ance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with
cold drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is
improper and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualified fitter or technician.
• Have electrical connections done by a qualified electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never
disconnect by pulling the power cord. Never touch the plug with wet fingers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
• Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts
to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fire.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer
service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive
substances (such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fire or
explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has
been used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil
may remain in the tub after a whole cycle resulting in fire during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where flammable substances are present such as oil, benzene or highly inflamma-
ble gas. Such materials may cause fire or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
ca. 100 cm
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
ca. 145 cm
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
ca. 105 cm
• When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to
protect children.
• When placing on a carpeted floor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fire.
• The cover cup of the filter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
• When this crossed-out wheeled bin symbol is attached to a product it means the product is cover-
Disposal
ed by European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately from municipal waste
stream
via designated collection facilities appointed by the government or the local authorities.
• The correct disposal of your old appliance will help prevent potential adverse consequences for the
environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city office,
waste disposal service or the shop where you purchased the product.
Safety instuctions for the installation
Safety instructions for use
Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug
To minimize the risk of fi re within the inner bowl, the following should be observed:
to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted floor. In countries where there is a risk of cockroach
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fire hazard and should not be
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
placed in a tumble dryer.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot CAUTION about positioning the appliance
escape, the items can become hot enough to catch fire. Piling, stacking or storing oil-affected items can prevent
Install the washing machine on a fl at hard fl oor. Make sure that air circulation around the washing machine is
heat from escaping and so create a fire hazard.
not impeded by carpets, rug etc.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care prod-
• Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
ucts be placed in a tumble dryer they should first be washed in hot water with extra detergent-this will reduce, • If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
but not eliminate, the hazard. The 'cool down' cycle of tumble dryers should be used to reduce the temperature
(85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
of the items. They should not be removed from the tumble dryer or piled or stacked while hot. • The washing machine must not be installed in rooms where the temperature may drop below 0°C.
• Please ensure that when the washing machine is installed, that a Service Technician can gain easy access in the event of a
• Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning
solvents or other flammable or explosive substances should not be placed in a tumble dryer. breakdown.
• Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
Highly flammable substances commonly used in domestic environments include acetone, denatured alcohol,
the top of the washing machine and underside of the worktop.
petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers.
• Items containing foam rubber (also known as latex foam) or similarly testured rubber like materials should not be
CAUTION about the power cord
dried in a tumble dryer on a heat setting.
We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse.. That is, a single outlet
Foam rubber materials can, when heated, produce fire by spontaneous combustion.
supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specifications
• Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static of this owner's manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension
electricity unless this practice is specifically recommended by the manufacturer of the fabric softener or product.
cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric
• Undergarments that contain metal reinforcements should not be placed in a tumble dryer. shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
Damage to the tumble dryer can result if metal reinforcements come loose during drying.
When available a drying rack could be used for such items. the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.
• Rubber-backed articles, clothes fitted with foam rubber pads, pillows, rubber boots and rubber-coated tennis
CAUTION about location and moving
shoes should not be placed in a tumble dryer.
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the
stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no floor drain
(gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic film,
Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not
allow children to play inside the bowl as they may become trapped.
CAUTION about the fl oor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a flat hard floor.
• Poorly constructed timber base floors can contribute to excessive noise and vibration.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and firmly in position.
• It must not "see-saw" across corners under load.
• The installation surface must be clean, free from floor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
 Technical Specifi cation
Name of product Front loading washing machine
Power supply
220-240 V~, 50 Hz
Size WxDxH mm:
600 x 640 x 850
Weight
73 kg
 Troubleshooting
• Water supply is not adequate in area Check another tap in the house.
• Water supply taps are not completely Fully open tap.
open.
• Water inlet hose(s) are kinked. Straighten hose(s).
• The fi lter of the inlet hose(s) are clogged. Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged. Clean and straighten the drain hose.
• The drain fi lter is clogged. Clean the drain filter.
For more detailed information, please
refer to "Cleaning the drain pump filter"
• Load is too small. Add 1 or 2 similar items to help balance
• Load is out of balance. the load.
• The appliance has an unbalance detection Rearrange load to allow proper spinning
and correction system. If individual heavy
articles are loaded (ex. bath mat, both
robe, etc.), this system may stop spinning
or even interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of
the cycle, add smaller articles of laundry to
balance the load and repeat the spin cycle.
• Floor is unstable. The fl oor should be a solid surface.
Feet are not adjusted Adjust the feet so that the machine
does not rock from side to side or front
to back.
• Is the door opened or not Close the door completely.
completely closed? If the " " does not clear, call for
service.
Unplug the power plug and call for
service.
• Water overfi lls due to the faulty water
Close the water tap.
valve.
Unplug the power plug.
Call for service.
• Water level sensor has malfunctioned.
• Over load in motor.
• The washer experienced a power Restart the cycle.
failure.
• Water leaks Call for service.
• Check water supply. Turn the tap on.
If " " is not released, unplug
power plug and call for service.
Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise Have all transit bolts and packing been removed?
Water leaks. Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary.
Excessive suds Too much detergent or unsuitable detergent.
Washing machine does not start Power cord may not be plugged in or connection may be loose.
Max. Watt 2100 W (Wash) / 1500 W (Dry)
Washing machine won't spin Check that the door is shut.
Capacity
Refer to the Rating Label
Check that foreign objects may be blocking the drain causing the water not to drain out.
Water consumption 73 Door does not open Once started, the door can not be opened for safety reasons.
At the end of the cycle or when Start Pause is pressed, wait one or two minutes before
Permissible water pressure 1.0-10 bar (100-1000kPa)
opening the door to allow the electric locking mechanism time to release.
Ownerʻs Manual
F1403RDS(1~9)
WD-20900
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner's manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your washing machine.
P/No.: MFL59755535