GE C30 Instruction Manual page 191

5 SETTINGS
Table 5–6: C30 FLEXLOGIC™ OPERANDS (Sheet 3 of 4)
OPERAND TYPE OPERAND SYNTAX
FIXED OPERANDS Off
On
INPUTS/OUTPUTS: Cont Ip 1
Contact inputs Cont Ip 2
↓
Cont Ip 1
Cont Ip 2
↓
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
↓
current
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
↓
INPUTS/OUTPUTS: Cont Op 1
Contact outputs, Cont Op 2
↓
voltage
(from detector on
Cont Op 1
form-A output only)
Cont Op 2
↓
INPUTS/OUTPUTS DIRECT INPUT 1 On
↓
Direct inputs
DIRECT INPUT 32 On
INPUTS/OUTPUTS: RemDPS Ip 1 BAD
Remote double- RemDPS Ip 1 INTERM
point status inputs
RemDPS Ip 1 OFF
RemDPS Ip 1 ON
REMDPS Ip 2...
INPUTS/OUTPUTS: REMOTE INPUT 1 On
↓
Remote inputs
REMOTE INPUT 32 On
INPUTS/OUTPUTS: Virt Ip 1
↓
Virtual inputs
Virt Ip 64
INPUTS/OUTPUTS: Virt Op 1
↓
Virtual outputs
Virt Op 96
LED INDICATORS: LED IN SERVICE
Fixed front panel LED TROUBLE
LEDs LED TEST MODE
LED TRIP
LED ALARM
LED PICKUP
LED VOLTAGE
LED CURRENT
LED FREQUENCY
LED OTHER
LED PHASE A
LED PHASE B
LED PHASE C
LED NEUTRAL/GROUND
LED INDICATORS: LED TEST IN PROGRESS
LED test
LED INDICATORS: LED USER 1
User-programmable
LED USER 2 to 48
LEDs
PASSWORD LOC SET ACCS AUT OFF
SECURITY LOC SET ACCS AUT ON
REM SET ACCS AUT OFF
REM SET ACCS AUT ON
UNAUTHORIZED ACCESS
GE Multilin
OPERAND DESCRIPTION
Logic = 0. Does nothing and may be used as a delimiter in an equation list;
used as 'Disable' by other features.
Logic = 1. Can be used as a test setting.
On (will not appear unless ordered)
On (will not appear unless ordered)
↓
Off (will not appear unless ordered)
Off (will not appear unless ordered)
↓
IOn (will not appear unless ordered)
IOn (will not appear unless ordered)
↓
IOff (will not appear unless ordered)
IOff (will not appear unless ordered)
↓
VOn (will not appear unless ordered)
VOn (will not appear unless ordered)
↓
VOff (will not appear unless ordered)
VOff (will not appear unless ordered)
↓
Flag is set, logic=1
↓
Flag is set, logic=1
Asserted while the remote double-point status input is in the bad state.
Asserted while the remote double-point status input is in the intermediate
state.
Asserted while the remote double-point status input is off.
Asserted while the remote double-point status input is on.
Same set of operands as per REMDPS 1 above
Flag is set, logic=1
↓
Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
On Flag is set, logic=1
↓
On Flag is set, logic=1
Asserted when the front panel IN SERVICE LED is on.
Asserted when the front panel TROUBLE LED is on.
Asserted when the front panel TEST MODE LED is on.
Asserted when the front panel TRIP LED is on.
Asserted when the front panel ALARM LED is on.
Asserted when the front panel PICKUP LED is on.
Asserted when the front panel VOLTAGE LED is on.
Asserted when the front panel CURRENT LED is on.
Asserted when the front panel FREQUENCY LED is on.
Asserted when the front panel OTHER LED is on.
Asserted when the front panel PHASE A LED is on.
Asserted when the front panel PHASE B LED is on.
Asserted when the front panel PHASE C LED is on.
Asserted when the front panel NEUTRAL/GROUND LED is on.
An LED test has been initiated and has not finished.
Asserted when user-programmable LED 1 is on.
The operand above is available for user-programmable LEDs 2 through 48.
Asserted while local setting access authorization is off.
Asserted while local setting access authorization is on.
Asserted while remote setting access authorization is off.
Asserted while remote setting access authorization is on.
Asserted when a password entry fails while accessing a password protected
level of the relay.
C30 Controller System
5.5 FLEXLOGIC™
5
5-71