Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Bosch WAP Series
Summary of Contents for Bosch WAP Series
- Page 1 Washing machine WAP... en Instruction Manual and Installation Instructions...
-
Page 2: Your New Washing Machine
Your new washing machine Display rules : Warning! You have chosen a Bosch washing machine. This combination of symbol and signal word indicates a possibly dangerous Please take a few minutes to read and situation. Not heeding the warning can become familiar with the advantages of cause death or injuries. -
Page 3: Table Of Contents
Contents e n I n s t r u c t i o n M a n u a l a n d I n s t a l l a t i o n I n s t r u c t i o n s Select additional programme Intended use. -
Page 4: Intended Use
Intended use Installation on a base or a wooden Intended use joist floor ..... 27 Installation on a platform with For private domestic use only. -
Page 5: Safety Instructions
Safety instructions If you lean on the washing Safety instructions ■ machine door when it is open, the washing machine Electrical safety may tip over and cause S a f e t y i n s t r u c t i o n s injuries. - Page 6 Safety instructions Warning Warning Danger of death! Risk of poisoning! Children may lock themselves Detergents and care products in appliances, putting their lives may be poisonous if at risk. consumed. For appliances that have Keep detergents and care reached the end of their service products out of the reach of life: children.
-
Page 7: Environmental Protection
Environmental protection Tips on economical use Environmental protection Always fill the appliance with the ■ maximum amount of laundry for each programme. Packaging/used appliance Overview of programmes ~: E n v i r o n m e n t a l p r o t e c t i o n Supplementary sheet for the Dispose of packaging in an operating and installation... -
Page 8: Getting To Know The Appliance
Getting to know the appliance Getting to know the appliance Washing machine G e t t i n g t o k n o w t h e a p p l i a n c e 9S Open the door Detergent dispenser 9T Close the door Control panel... -
Page 9: Control Panel
Getting to know the appliance Control panel You can find possible programme default settings and additional programme settings in the overview; these differ depending on the model. ( Programme default settings can be changed. Overview of all programme default settings ~ Page 13 0 additional programme settings can be selected. -
Page 10: Display Panel
Getting to know the appliance Display panel In the table you can find possible settings and information in the display panel; these differ depending on the model. Settings for the selected programme — - 90* Temperature in °C Temperature - - - -, 0 - 1400* Spin speed in rpm Maximum spin speed or - - - - (Rinse stop = without final spin, (revolutions per minute) washing remains in the water after the last rinse) -
Page 11: Laundry
Laundry – Light: Do not pretreat, select the Laundry G SpeedPerfect setting if necessary P repare the laundry – Normal L a u n d r y – Heavy: Load less laundry, pretreat the laundry if necessary. Caution! – Stains: Remove/pretreat stains Damage to the appliance/fabrics while they are fresh. -
Page 12: Detergent
Detergent Saving energy and detergent Detergent For light and normal soiling, you can C orrect selection of detergent save energy (lower washing D e t e r g e n t temperature) and detergent. The care label is crucial to ensure correct detergent selection, temperature Saving Soiling/note... -
Page 13: Programme Default Settings
Programme default settings Finish in time Programme default (ñ Ready in//ñ Finished in) settings Before starting the program, you can preselect the program end ("Finish in" You can find possible Note: P r o g r a m m e d e f a u l t s e t t i n g s time) in hourly increments (h = hour) up programme default settings in the to a maximum of 24 hours. -
Page 14: Additional Programme
Additional programme settings Rinse&Water Plus Additional programme (' Rinse Plus//Z Extra Water// settings Z Water Plus//Z Water plus) Increased water level and additional You can find possible additional Note: A d d i t i o n a l p r o g r a m m e s e t t i n g s programme settings in the overview;... -
Page 15: Operating The Appliance
Operating the appliance Change the programme Operating the default settings appliance You can use the default settings or change them. Install and connect washing Note: O p e r a t i n g t h e a p p l i a n c e machine properly. -
Page 16: Measure And Add Detergent And Care Products
Operating the appliance Notes Measuring Mix items of laundry of varying sizes. ■ Measure the detergent and care Laundry items of different sizes products according to: distribute themselves better during the spin cycle. Individual items of Water hardness; ask your water ■... -
Page 17: Start The Programme
Operating the appliance Pull out the detergent drawer as far Note: Foam detection as possible. If the Åsymbol also lights up in the Add detergent and/or care products. display panel, the washing machine has Close the detergent drawer. detected too much foam during the wash cycle and automatically activated Measuring aid* for liquid detergent additional rinse cycles to remove the... -
Page 18: Adding/Removing Laundry
Operating the appliance Adding/removing laundry Programme end during rinse hold Following the start of the program, you can add or remove laundry as required. - - - - 0 appears in the display panel and Press the A button to do this. the indicator lamp of the A button flashes. -
Page 19: Setting The Signal
Setting the signal Changing the volume Setting the signal Use the ñ Ready in//ñ Finished in + or - button to change the following settings You can change the following settings: at the corresponding program selector S e t t i n g t h e s i g n a l The volume for the information positions: ■... -
Page 20: Cleaning And Maintenance
Cleaning and maintenance Descaling Cleaning and Descaling should not be necessary if maintenance the detergent is measured out correctly. However, if it is required, follow the Warning manufacturer's instructions for the C l e a n i n g a n d m a i n t e n a n c e Danger of death! descaling agent. -
Page 21: The Drain Hose At The Siphon Is Blocked
Cleaning and maintenance Allow the water to cool down. Place the service flap back on, lock it into place, and close it. Turn off the water tap so that no more water can flow in and has to be drained via the drain pump. Switch off the appliance. -
Page 22: Filter In The Water Supply Blocked
Faults and what to do about them. Filter in the water supply Faults and what to do blocked about them. First, reduce the water pressure in the Emergency release supply hose: F a u l t s a n d w h a t t o d o a b o u t t h e m . Turn off the tap. -
Page 23: Information On The Display Panel
Faults and what to do about them. Information on the display panel Display Cause/Remedy Flashes fast + signal: The door was opened and the water level is too high. è ■ Close the door, continue the programme with A button or select 0 Spin/ Drain [ programme. - Page 24 Faults and what to do about them. Faults Cause/Remedy Water is not visible in the Not a fault – the water is below the visible area. drum. The spin result is not Not a fault – the unbalanced load detection system has interrupted the spin ■...
-
Page 25: After-Sales Service
After-sales service After-sales service Technical data If you cannot correct the fault yourself, Dimensions: A f t e r - s a l e s s e r v i c e T e c h n i c a l d a t a (see section, Faults and what to do 85 x 60 x 59cm about them ~ Page 22), please... -
Page 26: Positioning And Connecting
Positioning and connecting 8 Water inlet hose on aquaStop Positioning and models connecting @ Water outlet hose H Elbow for securing the water outlet hose* Included with the appliance P o s i t i o n i n g a n d c o n n e c t i n g P Cold water inlet hose on Standard/Aqua-Secure models Check the machine for transport... -
Page 27: Installation Surface
Positioning and connecting Installation on a platform with Caution! Water damage drawer The connection points for the water Platform order no.: WMZ 20490, supply hose and water drain hose are WZ 20490, WZ 20510, WZ 20520. under high water pressure. To prevent leaks and water damage, you must follow the instructions in this section. -
Page 28: Hose And Cable Lengths
Positioning and connecting Take the hoses out of the holders. Right-hand connection ■ Unscrew and remove all four transport brace screws. Remove the sleeves. To do this, remove the mains cable from the *Depending on the model holders. The following are available from Tip: specialist dealers/the after-sales service:... -
Page 29: Water Outlet
Positioning and connecting Open the water tap carefully, Optimum water pressure in the supply network checking the leak tightness of the connection points. The screw At least 100 kPa (1 bar) connection is under mains water Maximum 1000 kPa (10 bar) pressure. -
Page 30: Levelling
Positioning and connecting Electrical connection Drainage into a siphon ■ The connection point must be secured using a hose clamp with a Warning diameter of 24-40 mm (available from Danger of death! specialist dealers). There is a risk of electric shock if you touch live components. -
Page 31: Before Washing For The First Time
Positioning and connecting Before washing for the first Transportation time e.g. when moving home The washing machine was thoroughly Preparatory work: tested before leaving the factory. To Turn off the water tap. remove any water that may be left over Reduce the water pressure in the from the test, run the first wash cycle supply hose. - Page 32 0344 892 8979 (Calls charged at local or mobile rate.) 01450 2655 (0.03 € per minute at peak. Off peak 0.0088 € per minute.) You can find the contact information for all countries in the attached after-sales service directory. Robert Bosch Hausgeräte GmbH Carl-Wery-Straße 34 81739 München, GERMANY *9001051717*...