Stylish portable dvd player with 7" lcd and usb to access movies, photos and music straight from your pc. available in four great glossy colours for every taste. (184 pages)
Page 1
DVP-F5/FX1 3 7 63 1515 0 RMT-D114A SERVICE MANUAL US Model Canadian Model AEP Model UK Model Chinese Model DVP-FX1/F5 Hong Kong Model DVP-FX1 Australian Model DVP-F5 Photo: DVP-FX1 Manufactured under license from Dolby Laboratories Licensing Corporation. “DOLBY” and the double-D symbol ; are trademarks of Dolby Laboratories Licensing Corporation.
Page 3
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS L 13942296513 OU DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
Page 4
http://www.xiaoyu163.com 3 7 63 1515 0 TABLE OF CONTENTS GENERAL 2-4. CD, LID ··········································································· 2-2 2-5. MB-90 Board, LC-68 Board, MD Comple ····················· 2-2 About this manual ··························································· 1-1 2-6. Display Panel (FX1) ························································ 2-3 This Player Can Play the Following Discs ······················ 1-1 Precautions ······································································...
Double-sided handling the optical pick-up block as service parts. adhesive tape 2) The optical pick-up of the DVP-F5/FX1 cannot be replaced as Hold a single part. It is supplied as the MD COMPLE (DVDM- position FX1).
Page 9
DVP-F5/FX1 SECTION 1 This section is extracted from GENERAL 3 7 63 1515 0 instruction manual. L 13942296513 u163 http://cxema.ru http://www.xiaoyu163.com...
Page 38
http://www.xiaoyu163.com 3 7 63 1515 0 2-4. CD, LID CD, LID Plate(CD LID) Assy ful crum 2 Tension spring (open) 1 Screw (M1.7 x 3) 3 Compression spring 2 Open blacket 4 Lock lever 1 Screw (M1.7 x 3) L 13942296513 2-5.
Page 75
DVP-F5/FX1 SECTION 5 IC PIN FUNCTION 3 7 63 1515 0 5-1. SYSTEM CONTROL (MB-90 BOARD IC002: MB91107PFV-G-BEN) Pin No. Pin Name Description 1 to 5 HA17 to HA21 Address bus A17 to A21 − HA22 Not used A23/P67...
Page 76
http://www.xiaoyu163.com 3 7 63 1515 0 Pin No. Pin Name Description − Power supply CKSW1 Chuck sensor input OCSW1 Tray sensor input OCSW2 Tray sensor input 2CH_CS Chip select signal output to DAC (2CH) VES_CS Chip select signal output to VES DSP 48/44.1K PLL FS control signal output MAMUTE...
Page 77
http://www.xiaoyu163.com 3 7 63 1515 0 5-2. IF CONTROL (MB-90 BOARD IC701: M37513MB-055GP) GP Pin Pin name Function DCOUNT MNT External power supply voltage monitor input KEY3 D KEY3 input KEY2 D KEY2 input KEY1 D KEY1 input CHGMNT Battery voltage input TEMP Main unit temperature measurement VCCMNT...
Page 78
http://www.xiaoyu163.com 3 7 63 1515 0 (RESERVE) (RESERVE) (RESERVE) (RESERVE) INV_H_L TFT inverter 2-step dimmer control output SRSCNT SRS control output V_IOCNT VIDEO input/output selector switch output IRPCON REMOCON receptor power supply control output DVDPCON Power supply control output of disc playback system VMUTE_TFT VMUTE output for TFT LCD panel XFRRST...
DVP-F5/FX1 SECTION 6 TEST MODE 3 7 63 1515 0 6-1. GENERAL DESCRIPTION ### Syscon Diagnosis ### The Test Mode allows you to make diagnosis and adjustment easily Diag All Check using the remote commander and monitor TV. The instructions, No.
Page 80
Data write → read, and accord check DVP-FX1 Error 09 : ←→ RAM data bus error DVP-F5 Data 0x0001 to 0x8000 where one bit each is set to 1 are written to the address 0 of RAM (IC603) connected to the...
Page 81
http://www.xiaoyu163.com 3 7 63 1515 0 (5-4) ARP to RAM Address Bus 6. AV Decoder Data write → other address read discord check (6-2) 1932 RAM Error 10 : ARP → RAM data bus error Data write → read, and accord check Caution : Address and data display in case of an error is Error 13 : ARP RAM read data discord...
Page 82
http://www.xiaoyu163.com 3 7 63 1515 0 Check Items List Error Codes List 2. Version 00: Error not detected (2-2) Revision 01: RAM write/read data discord (2-3) ROM Check Sum 02: Gate array NG (2-4) Model type 03: EEPROM NG (2-5) Region 04: Flashmemory clear error 05: Flash memory write error...
http://www.xiaoyu163.com 3 7 63 1515 0 6-4. DRIVE AUTO ADJUSTMENT 1. DVD-SL (single layer disc) Select 1 , insert DVD single layer disc, and press ENTER key, and the adjustment will be made through the following steps, then On the Test Mode Menu screen, press 1 key on the remote adjusted values will be written to the EEPROM.
Page 84
http://www.xiaoyu163.com 3 7 63 1515 0 2. CD (CD disc) 3. DVD-DL (dual layer disc) Select 2 , insert CD disc, and press ENTER key, and the Select 3 , insert DVD dual layer disc, and press ENTER key, adjustment will be made through the following steps, then adjusted and the adjustment will be made through the following steps, then values will be written to the EEPROM.
http://www.xiaoyu163.com 3 7 63 1515 0 4. SACD (SACD disc) 6-5. DRIVE MANUAL OPERATION Select 4 , insert SACD disc, and press ENTER key, and the adjustment will be made through the following steps, then adjusted On the Test Mode Menu screen, select 2 , and the manual operation values will be written to the EEPROM.
Page 86
http://www.xiaoyu163.com 3 7 63 1515 0 On this screen, the mirror time is measured to judge the disc and it is written to the EEPROM. First load DVD SL disc and press 1 , Disc Type next load CD disc and press 2 , and finally load DVD DL disc and 1.
http://www.xiaoyu163.com 3 7 63 1515 0 Reset SLED TILT Reset the Sled and Tilt to initial position. 6-6. EVR Adjustment Turn ON/OFF the laser. Turn ON/OFF the spindle. The picture display adjustment of both NTSC and PAL can be Focus Search the focus and turn on the focus.
Page 88
http://www.xiaoyu163.com 3 7 63 1515 0 5 Copy NTSC → PAL * Pressing the UP or DOWN key of the cursor key of the remote control increments or decrements the binary number. At the 6 Copy PAL → NTSC same time, value of the binary number is written in the PROM of the EVR IC.
http://www.xiaoyu163.com 3 7 63 1515 0 6-7. EMERGENCY HISTORY Emergency Codes List 10 : Communication to IC801 (MB-90 board) failed. 11 : Each servo for focus, tracking, and spindle is unlocked. ### MEG. History 12 : Communication to EEPROM, IC001 (MB-90 board) failed. 13 : Writing of hours meter data to EEPROM, IC001 (MB-90 board) Laser Hours CD xxxxxxxh...
http://www.xiaoyu163.com 3 7 63 1515 0 6-8. VERSION INFORMATION 6-10. SELF-DIAGNOSIS OF IF CONTROLLER 1. IF Controller Test Mode ## Version Information ## The IF controller test mode means the self-diagnosis mode of the IF con. Ver. x. xxx (xxx) IF controller.
Page 91
http://www.xiaoyu163.com 3 7 63 1515 0 3. How To Exit The Test Mode 4. Description of IF Controller Function Check Mode Press the 0 key and the ENTER key at the same time on the All functions can be operated by pressing the numeric key on the remote control unit.
Page 92
http://www.xiaoyu163.com 3 7 63 1515 0 8. KEY check 13. Forced ON output to TFT LCD INVPCON Command : 08 Command : 13 Operation : The LCD segments as many as the number of the Operation : The TFT LCD inverter is set to the forced ON key switches are turned on.
Page 93
http://www.xiaoyu163.com 3 7 63 1515 0 22. Auto LCD test display 28. TFT LCD EVR adjustment (NTSC setting) Command : 22 Command : 28 Operation : The following operation is repeated. Operation : Even when the LINE IN/OUT is switched by LCD all segments turn on (5 seconds) All the VIDEO switch for the TFT LCD monitor segments turn on (5 seconds) →...
Page 94
http://www.xiaoyu163.com 3 7 63 1515 0 31. CHGCNT OFF & LBCHG ON 37. CHGMNT voltage during charging display (when Command : 31 CHGMNT = ON) Operation : The CHGCNT is forced to OFF and the LBCHG Command : 37 is forced to ON. Operation : The CHGMNT voltage that is inputted by the When charging is in progress in the STAND-...
Page 95
http://www.xiaoyu163.com 3 7 63 1515 0 41. BATT switch check and BATTYPE check Command : 41 LCD display : “41 − m n” m : BATT switch = “1” (Already connected state) or “0” (Not connected yet state) display. m : BATTYPE = “1” (Lithium-ion battery) or “0” (Other batteries than the lithium-ion battery) display.
DVP-F5/FX1 SECTION 7 ELECTRICAL ADJUSTMENT 3 7 63 1515 0 3. Charge Voltage Adjustment (MB-90 Board) In making adjustment, refer to 6-4. Adjustment Mode CHG “30” is forced to be set in test mode Related Parts Arrangement. Measurement Point Between JL501 3 and JL503 #...
http://www.xiaoyu163.com 3 7 63 1515 0 7-2. SYSTEM CONTROL ADJUSTMENT 7-3. VIDEO SYSTEM ADJUSTMENT (TP-61 Board) 1. Video Level Adjustment (MB-90 Board) 1. Free Run Level Sync Frequency (or 19.98 MHz) Purpose Adjustment (TP-61 board) This adjustment is made to satisfy the standard, and if not adjusted correctly, the brightness will be too large or small.
DVP-F5/FX1 SECTION 8 REPAIR PARTS LIST 3 7 63 1515 0 8-1. EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number The components identified by mark 0or have some differences from the original one.
Page 102
http://www.xiaoyu163.com 3 7 63 1515 0 8-1-1. MAIN SECTION (FX1) L 13942296513 supplied u163 http://cxema.ru http://www.xiaoyu163.com...
DVP-F5/FX1 LC-68 MB-90 3 7 63 1515 0 8-2. ELECTRICAL PARTS LIST NOTE: • RESISTORS When indicating parts by reference number, • Due to standardization, replacements in the All resistors are in ohms. please include the board name. parts list may be different from the parts...