Advertisement

SERVICE MANUAL
Ver. 1.6 2006.03
US and foreign patents licensed from
Dolby Laboratories.
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the objective lens surface on
the optical pick-up block with 7 mm aperture.)
D-A conversion
1-bit quartz time-axis control
Frequency response
+1
20 - 20 000 Hz
dB (measured by JEITA CP-
–2
307)
Output (at 4.5 V input level)
Line output (stereo minijack)
Output level 0.7 V rms at 47 kΩ
Recommended load impedance
over 10 kΩ
Headphones (stereo minijack)
Approx. 5 mW at 16 Ω
Approx. 5 mW +
Approx. 1.5 mW at 16 Ω)*
(Approx. 1.5 mW +
*For the customers in Europe
Optical digital output (optical output connector)
Output level: –21 - –15 dBm
Wavelength: 630 - 690 nm at peak level
Sony Corporation
9-877-308-07
2006C16-1
Personal Audio Division
© 2006.03
Published by Sony Techno Create Corporation
D-NE1/NE9
Photo : D-NE9
Model Name Using Similar Mechanism NEW
CD Mechanism Type
Optical Pick-up Name
SPECIFICATIONS
Power requirements
For the area code of the model you
purchased, check the upper left side of the
bar code on the package.
• Two Sony NH-14WM (A) rechargeable
batteries: 1.2 V DC × 2
• Two LR6 (size AA) batteries: 1.5 V DC × 2
• AC power adaptor (DC IN 4.5 V jack):
US,
Canadian and Taiwan models:
120 V, 60 Hz
UK model: 230 V, 50 Hz
Australian model: 240V , 50 Hz
AEP, Tourist, E18, Korean and East Europe models:
100 - 240 V, 50/60 Hz
Hong Kong model: 230 V, 50 Hz
Chinese model: 220 V, 50 Hz
1
Battery life*
(approx. hours)
(When you use the CD player on a flat and stable
surface)
Playing time varies depending on how the CD
player is used.
US Model
Canadian Model
AEP Model
UK Model
E Model
Australian Model
Chinese Model
Tourist Model
CDM-3325ER2
DAX-25E
When using two NH-14WM (A) (charged for
2
about 5 hours*
)
< > : NH-10WM
G-PROTECTION
"1"
Audio CD
35 < 25 >
3
ATRAC3plus file*
55 < 40 >
4
MP3 file*
50 < 35 >
When using external battery case (two alkaline
5
batteries*
)
G-PROTECTION
"1"
Audio CD
55
3
ATRAC3plus file*
95
4
MP3 file*
85
When using two NH-14WM (A) and external
battery case (two alkaline batteries*
< > : NH-10WM
G-PROTECTION
"1"
Audio CD
90 < 80 >
3
ATRAC3plus file*
150 < 135 > 150 < 135 >
4
MP3 file*
135 < 120 > 135 < 120 >
• Abbreviation
E18: 100-230V AC area in E model
— Continued on next page —
PORTABLE CD PLAYER
D-NE1
D-NE1/NE9
D-NE1
D-NE1/NE9
"2"
32 < 23 >
55 < 40 >
50 < 35 >
"2"
50
95
85
5
)
"2"
82 < 73 >

Advertisement

Table of Contents
loading

Summary of Contents for Sony D-NE1

  • Page 1 < > : NH-10WM Laser diode properties bar code on the package. G-PROTECTION Material: GaAlAs • Two Sony NH-14WM (A) rechargeable Wavelength: λ = 780 nm “1” “2” batteries: 1.2 V DC × 2 Emission duration: Continuous Audio CD 35 <...
  • Page 2: Table Of Contents

    *3 Recorded at 48 kbps or 64 kbps 2. GENERAL ·········································································· 5 *4 Recorded at 128 kbps *5 When using Sony alkaline batteries LR6 (SG) (produced in Japan) 3. DISASSEMBLY ································································ 7 3-1. Upper Lid Section ························································· 7 Operating temperature 3-2.
  • Page 3: Servicing Note

    LASER DIODE AND FOCUS SEARCH OPERATION CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE CHECK REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY During normal operation of the equipment, emission of the laser DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU diode is prohibited unless the upper lid is closed while turning ON DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
  • Page 4 D-NE1/NE9 SERVICE MODE 2. Operation when the Service Mode is set. When the Service Mode becomes active, following messages are The following confirmation can be performed when the Service displayed onthe remote control LCD. Mode is set. 1. How to set the Service Mode.
  • Page 5: General

    D-NE1/NE9 SECTION 2 GENERAL This section is extracted from instruction manual. Locating the controls CD player (front) (D-NE1) 1 Jog lever (u (play/pause)• ./> (AMS/search)) (pages 13, 14, 20 - 22) 2 x (stop) /CHARGE button• CHARGE lamp (pages 14, 25, 26, 28, 29) 3 VOL (volume) +*/–...
  • Page 6 D-NE1/NE9 CD player (rear) 0 EXT BATT (external battery)/ DC IN 4.5 V (external power input) jack (pages 13, 29, 31) qa LINE OUT (OPTICAL) jack (page 27) +/– buttons (pages 14, 22) qd HOLD switch (page 25) Remote control...
  • Page 7: Disassembly

    Follow the disassembly procedure in the numerical order given. 3-1. Upper Lid Section 1 tapping screw (B2) 3 tapping screw (B2) 4 guide (R) 2 guide (L) The form of fulcrum plate differs in the D-NE1 and D-NE9. upper lid block assy...
  • Page 8: Cabinet (Upper) Section

    D-NE1/NE9 3-2. Cabinet (upper) Section 4 claw 1 seven tapping screws (B2) 5 three claws 2 tapping screw (B2) 7 cabinet (upper) block assy 3 claw 6 claw 9 spring (upper lid) 8 battery terminal board (relay) cabinet (lower) block assy...
  • Page 9: Main Board

    D-NE1/NE9 3-3. MAIN Board, CD Mechanism Section (CDM-3325ER2) 4 CD mechanism deck (CDM-3325ER2) 1 connector (2P) (CN401) 2 connector (4P) (CN402) 3 flexible board (CN601) 9 battery terminal board (+) 7 charge terminal board (+) 6 charge terminal board (-)
  • Page 10: Motor Assy (Spindle)(M901), Motor Assy (Sled)(M902), Optical Pick-Up Assy (Dax-25E)

    D-NE1/NE9 3-4. Motor Assy (Spindle)(M901), Motor Assy (Sled)(M902), Optical Pick-up Assy (DAX-25E) 1 three screws (B1.7x4) 2 gear cover 3 motor assy (sled) (M902) 5 three screws (B1.7x4) 4 optical pick-up (DAX-25E) 6 turn table motor assy (spindle) (M901) chassis...
  • Page 11: Electrical Checking

    D-NE1/NE9 SECTION 4 ELECTRICAL CHECKING The CD section adjustments are done automatically in this set. RF Level Check In case of operation check, confirm that RF level. Condition: • Hold the set in horizontal state. Precautions for Check Perform check in the order given.
  • Page 12: Diagrams

    D-NE1/NE9 SECTION 5 DIAGRAMS NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS Note on Printed Wiring Board Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or • X : parts extracted from the component side.
  • Page 13: Block Diagram

    D-NE1/NE9 5-1. Block Diagram IC601 Q303, 803 RF AMP,SERVO,DSP, D/A CONV,D-RAM CONT VCC3 DOUT AOUT1 J302 OPTICAL PICK-UP LINE OUT AOUT2 (OPTICAL) DAX-25E DETECTOR Q302 Q101 Q201 RFAC LRMU MUTING MUTING MUTING RFDC CONTROL IC603 DRAM VCC1_2.25V IC302 IC301 SWITCH...
  • Page 14: Printed Wiring Boards - Main Board (Side A)

    D-NE1/NE9 Ver 1.3 2003.08 5-2. Printed Wiring Board – MAIN Board (Side A) – • : Uses unleaded solder. S801 > S806 DIAL CHARGE MAIN BOARD (SIDE A) S809 S808 J401 EXT BATT J301 DC IN 4.5V IC302 IC603 IC701...
  • Page 15: Printed Wiring Boards - Main Board (Side B)

    D-NE1/NE9 Ver 1.3 2003.08 5-3. Printed Wiring Board – MAIN Board (Side B) – • : Uses unleaded solder. When IC803 is damaged, replace the MAIN board. MAIN BOARD (SIDE B) (HOLDER) S804 S805 J302 LINE OUT (OPTICAL) S810 HOLD...
  • Page 16: Schematic Diagrams - Main Board (1/4)

    D-NE1/NE9 5-4. Schematic Diagrams – MAIN Board (1/4) – • See page 12 for Waveforms. C621 47 6.3V FB605 R612 C619 22 6.3V C321 IC302 R636 FB604 SN74LVC2G66DCUR L602 AP638 AP637 AP631 XWIH XEMP XWRE VDR602 R648 AP630 100k CN601...
  • Page 17: Schematic Diagrams - Main Board (2/4)

    D-NE1/NE9 5-5. Schematic Diagrams – MAIN Board (2/4) – • See page 12 for Waveform. • See page 20 for IC Block Diagrams. Q303 DTA143EUA-T106 Q302 XP4312-TXE J302 C313 C205 R207 R302 R303 FB305 R206 Q201 Q101 TP307 100k 2SD2652...
  • Page 18: Schematic Diagrams - Main Board (3/4)

    D-NE1/NE9 Ver 1.3 2003.08 5-6. Schematic Diagrams – MAIN Board (3/4) – • See page 12 for Waveform. TP510 CN401 TP495 TP496 TP491 TP492 TP493 TP494 R452 220k CN402 D421 MA111-TX R415 470k R414 L406 L409 R453 C435 FB415 47 6.3V...
  • Page 19: Schematic Diagrams - Main Board (4/4)

    D-NE1/NE9 Ver 1.3 2003.08 5-7. Schematic Diagrams – MAIN Board (4/4) – • See page 12 for Waveform. When IC803 is damaged, replace the MAIN board. R879 IC806 XC6206P152MR TP805 Q803 C821 DTC124XE-TL R878 C810 TP804 TP907 S810 R866 HOLD...
  • Page 20: Ic Block Diagram

    D-NE1/NE9 5-8. IC Block Diagrams IC301 TA2120FN (EL) IC701 CXR710160-210R BIAS BIAS MUTE MUTE_τ BEEP 64 63 62 61 60 59 58 57 56 55 52 51 50 49 BEEP BIAS OUT B OUT A PE3/RxD1 PE2/TxD1 PE1/RxD0 PE0/TxD0 INTERFACE...
  • Page 21: Ic Pin Function Descriptions

    D-NE1/NE9 5-9. IC Pin Function Descriptions • IC601 CXD3039AR (RF AMP, DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR, D-RAM CONTROLLER) Pin No. Pin Name Description XRAS Row address strobe signal output to the D-RAM Data input enable signal output to the D-RAM...
  • Page 22 D-NE1/NE9 Pin No. Pin Name Description 53, 54 AVSS1, AVSS2 — Ground terminal (analog system) VREFR R-ch reference voltage output terminal AOUT2 R-ch analog audio signal output AVDD2 — Power supply terminal (analog system) TES1 Input terminal for the test (normally: fixed at “L”) TEST Input terminal for the test (normally: fixed at “L”)
  • Page 23 D-NE1/NE9 Pin No. Pin Name Description SFDR Sled servo drive signal (+) output to the TB2130AF SSTP Disc inner position detection signal input terminal Not used Spindle motor drive signal output to the spindle motor driver Spindle motor servo control signal output to the spindle motor driver C176 176.4 kHz clock signal output to the power control and spindle motor driver...
  • Page 24 D-NE1/NE9 • IC801 TMP91CW28FG-4PNO Pin No. Pin Name Description — Reference voltage terminal (A/D converter) — Ground terminal (A/D converter) VCPU — Power supply terminal (A/D converter) XRST_O Reset signal output to the DSP (IC601) PWM_O Not used (open) BEEP_O...
  • Page 25 D-NE1/NE9 Pin No. Pin Name Description BAT_VCC_O Battery power switch control signal output DTS_RST_O Not used (open) AT3_MP3_V_O Reset signal output to the decoder (IC701) P/S_O Not used (open) — Ground terminal XNMI_I Not used (fixed at “H”) VCPU —...
  • Page 26: Exploded Views

    D-NE1/NE9 Ver. 1.6 SECTION 6 EXPLODED VIEWS NOTE: • -XX, -X mean standardized parts, so they may • Accessories are given in the last of electrical The components identified by mark 0 or have some differences from the original one.
  • Page 27 D-NE1/NE9 Ver 1.3 2003.08 6-2. Cabinet (lower) Section CD mechanism deck section (CDM-3325ER2) Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-245-312-01 BATTERY TERMINAL (+) X-3383-612-1 CABINET ASSY (ML), LOWER (BLUE) X-3383-517-1 CABINET ASSY, LOWER (NE9:AEP,EE)
  • Page 28 D-NE1/NE9 Ver 1.5 2004.08 6-3. CD Mechanism Deck Section (CDM-3325ER2) M901 M902 Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks 3-318-203-61 SCREW (B1.7X4), TAPPING 3-221-475-01 SHAFT, STANDARD 0 102 X-3380-950-1 OPTICAL PICK-UP (DAX-25E) 3-222-298-01 RACK 3-221-473-01 COVER, GEAR...
  • Page 29: Electrical Parts List

    D-NE1/NE9 Ver 1.3 2003.08 SECTION 7 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in the • RESISTORS • SEMICONDUCTORS In each case, u: µ, for example: parts list may be different from the parts All resistors are in ohms.
  • Page 30 D-NE1/NE9 Ver 1.5 2004.08 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks C701 1-107-820-11 CERAMIC CHIP 0.1uF FB301 1-500-234-22 FERRITE C702 1-104-847-11 TANTAL. CHIP 22uF 20.00% 4V FB303 1-500-234-22 FERRITE C703 1-107-820-11 CERAMIC CHIP 0.1uF...
  • Page 31 D-NE1/NE9 Ver 1.3 2003.08 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks Q410 8-729-426-24 TRANSISTOR XP1211-TXE R425 1-216-864-11 METAL CHIP 1/16W Q411 8-729-055-99 TRANSISTOR MCH3309 R426 1-218-985-11 RES-CHIP 470K 1/16W Q414 6-550-355-01 TRANSISTOR RTQ045N03TR R427...
  • Page 32 D-NE1/NE9 Ver 1.3 2003.08 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks R643 1-218-990-11 SHORT CHIP R838 1-218-990-11 SHORT CHIP R645 1-218-990-11 SHORT CHIP R839 1-218-990-11 SHORT CHIP R646 1-216-864-11 METAL CHIP 1/16W R840 1-218-990-11 SHORT CHIP...
  • Page 33 D-NE1/NE9 Ver 1.2 2003.06 MAIN Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks < VARISTOR > 3-252-232-51 MANUAL, INSTRUCTION (FOR SONIC STAGE,SIMPLE BURNER) VDR401 1-801-864-21 VARISTOR, CHIP (1608) (POLISH,CZECH,SLOVAK)(NE1:EE/NE9:EE) VDR403 1-801-864-21 VARISTOR, CHIP (1608) 3-252-232-61 MANUAL, INSTRUCTION...
  • Page 34 D-NE1/NE9 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2003.04...

This manual is also suitable for:

D-ne9

Table of Contents