Page 1 Accessories, spare parts and modification of your Toyota A wide variety of non-genuine spare parts and accessories for Toyota vehi- cles are currently available in the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
Page 2 ● Usage of data collected through Safety Connect (U.S.mainland only) If your Toyota has Safety Connect and if you have subscribed to those ser- vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.
Page 3 EDR. ● Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except when: • An agreement from the vehicle’s owner (or the lessee for a leased vehi- cle) is obtained •...
Page 4 Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Page 5 1-1. For safe use Before driving Floor mat Use only floor mats designed specifically for vehicles of the same model and model year as your vehicle. Fix them securely in place onto the carpet. Insert the retaining hooks (clips) into the floor mat eyelets. Turn the upper knob of each retaining hook (clip) to secure the floor mats in place.
Page 6 When installing the driver’s floor mat ● Do not use floor mats designed for other models or different model year vehicles, even if they are Toyota Genuine floor mats. ● Only use floor mats designed for the driver’s seat. ●...
Page 7 1-1. For safe use For safety drive For safe driving, adjust the seat and mirror to an appropriate position before driving. Correct driving posture Adjust the angle of the seat- back so that you are sitting straight up and so that you do not have to lean forward to steer.
Page 8 1-1. For safe use Adjusting the mirrors Make sure that you can see backward clearly by adjusting the inside and outside rear view mirrors properly. (P. 129, 131) WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ●...
Page 9 1-1. For safe use Seat belts Make sure that all occupants are wearing their seat belts before driving the vehicle. Correct use of the seat belts ● Extend the shoulder belt so that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoulder.
Page 10 1-1. For safe use Adjusting the seat belt shoulder anchor height (front seats) Push the seat belt shoulder anchor down while pressing the release button. Push the seat belt shoulder anchor up. Move the height adjuster up and down as needed until you hear a click.
Page 11 Toyota dealer free of charge. ■ Rear seat belt Use the seat belt after passing it through the guide if the seat belt comes free from the guide.
Page 12 Each seat belt should be used by one person only. Do not use a seat belt for more than one person at once, including children. ● Toyota recommends that children be seated in the rear seat and always use a seat belt and/or an appropriate child restraint system. ●...
Page 13 ● Ensure that the belt and plate are locked and the belt is not twisted. If the seat belt does not function correctly, immediately contact your Toyota dealer. ● Replace the seat assembly, including the belts, if your vehicle has been involved in a serious accident, even if there is no obvious damage.
Page 14 1-1. For safe use WARNING ■ Using a seat belt extender ● Do not wear the seat belt extender if you can fasten the seat belt without the extender. ● Do not use the seat belt extender when installing a child restraint system because the belt will not securely hold the child restraint system, increas- ing the risk of death or serious injury in the event of an accident.
Page 15 1-1. For safe use SRS airbags The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury. ◆...
Page 16 1-1. For safe use ◆ SRS side and curtain shield airbags SRS front side airbags Can help protect the torso of the front seat occupants SRS rear side airbags Can help protect the torso of occupants in the rear outer seats SRS curtain shield airbags ●...
Page 17 1-1. For safe use SRS airbag system components Front impact sensors “AIR BAG ON” and “AIR BAG OFF” indicator lights Front passenger occupant classification system (ECU SRS warning light and sensors) Front passenger’s seat belt Knee airbags buckle switch Side impact sensors (front Airbag sensor assembly doors) Side impact sensors (rear)
Page 18 1-1. For safe use WARNING ■ SRS airbag precautions Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury. ● The driver and all passengers in the vehicle must wear their seat belts properly.
Page 19 An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys- tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat.
Page 20 1-1. For safe use WARNING ■ SRS airbag precautions ● Do not sit on the edge of the seat or lean against the dashboard. ● Do not allow a child to stand in front of the SRS front passenger airbag unit or sit on the knees of a front passenger.
Page 21 1-1. For safe use WARNING ■ SRS airbag precautions ● Do not attach anything to or lean any- thing against areas such as the dash- board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.
Page 22 If the areas where the SRS airbags are stored, such as the steering wheel pad and front and rear pillars garnishes, are damaged or cracked, have them replaced by your Toyota dealer. ● Do not place anything, such as a cushion, on the front passenger's seat.
Page 23 Modification and disposal of SRS airbag system components Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Page 24 1-1. For safe use ■ If the SRS airbags deploy (inflate) ● Bruising and slight abrasions may result from contact with a deploying (inflating) SRS airbag. ● A loud noise and white powder will be emitted. ● Parts of the airbag module (steering wheel hub, airbag cover and inflator) as well as the front seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes.
Page 25 1-1. For safe use ■ Conditions under which the SRS airbags may deploy (inflate), other than a collision The SRS front airbags and SRS side and curtain shield airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.
Page 26 1-1. For safe use ■ Types of collisions that may not deploy the SRS airbags (SRS side and curtain shield airbags) The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
Page 27 1-1. For safe use ■ When to contact your Toyota dealer In the following cases, the vehicle will require inspection and/or repair. Con- tact your Toyota dealer as soon as possible. ● Any of the SRS airbags have been inflated. ●...
Page 28 1-1. For safe use Front passenger occupant classification system Your vehicle is equipped with a front passenger occupant classi- fication system. This system detects the conditions of the front passenger seat and activates or deactivates the devices for the front passenger. SRS warning light Seat belt reminder light “AIR BAG OFF”...
Page 29 1-1. For safe use Condition and operation in the front passenger occupant classi- fication system Adult ■ “AIR BAG ON” and “AIR BAG OFF” indi- “AIR BAG ON” cator lights Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Side airbag on the front...
Page 30 1-1. For safe use Child restraint system with infant ■ “AIR BAG ON” and “AIR BAG OFF” indica- “AIR BAG tor lights OFF” Indicator/ SRS warning light warning light Seat belt reminder light flashing Front passenger airbag Deactivated Side airbag on the front passenger seat Activated Devices...
Page 31 1-1. For safe use There is a malfunction in the system ■ “AIR BAG ON” and “AIR BAG OFF” “AIR BAG indicator lights OFF” Indicator/ warning light SRS warning light Seat belt reminder light Front passenger airbag Deactivated Side airbag on the front passenger seats Activated Devices...
Page 32 1-1. For safe use WARNING ■ Front passenger occupant classification system precautions Observe the following precautions regarding the front passenger occupant classification system. Failure to do so may cause death or serious injury. ● Wear the seat belt properly. ● Make sure the front passenger’s seat belt plate has not been left inserted into the buckle before someone sits in the front passenger seat.
Page 33 SRS warning light may come on to indicate a malfunction of the front passenger occupant classification system. In this case, contact your Toyota dealer immediately. ● Child restraint systems installed on the rear seat should not contact the front seatbacks.
Page 34 1-1. For safe use Safety information for children Observe the following precautions when children are in the vehi- cle. Use a child restraint system appropriate for the child, until the child becomes large enough to properly wear the vehicle’s seat belt.
Page 35 1-1. For safe use Child restraint systems A child restraint system for a small child or baby must itself be properly restrained on the seat with the LATCH anchors or the lap portion of the lap/shoulder belt. The laws of all 50 states of the U.S.A. and Canada now require the use of child restraint systems.
Page 36 1-1. For safe use Types of child restraints Child restraint systems are classified into the following 3 types according to the age and size of the child: Rear facing  Infant seat/con- Forward facing  Convertible   vertible seat seat Booster seat ...
Page 37 ● Toyota strongly urges the use of a proper child restraint system that con- forms to the size of the child, installed on the rear seat. According to acci- dent statistics, the child is safer when properly restrained in the rear seat than in the front seat.
Page 38 1-1. For safe use WARNING ■ When children are in the vehicle Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death.
Page 39 1-1. For safe use Installing child restraints Follow the child restraint system manufacturer's instructions. Firmly secure child restraints to the seats using the LATCH anchors or a seat belt. Attach the top tether strap when installing a child restraint. The lap/shoulder belt can be used if your child restraint system is not compatible with the LATCH (Lower Anchors and Tethers for Children) system.
Page 40 1-1. For safe use Installation with LATCH system Widen the gap between the seat cushion and seatback slightly. Type A  Latch the hooks of the lower straps onto LATCH anchors. If the child restraint has a top tether strap, the top tether strap should be latched onto the top tether strap anchor.
Page 41 1-1. For safe use Installing child restraints using a seat belt (child restraint lock function belt) Rear-facing  Infant seat/convertible seat ■ Place the child restraint sys- tem on the rear seat facing the rear of the vehicle. Run the seat belt through the child restraint system and insert the plate into the buckle.
Page 42 1-1. For safe use While pushing child restraint system down into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 43 1-1. For safe use While pushing child restraint system into the rear seat, allow the shoulder belt to retract until the child restraint system is securely in place. After the shoulder belt has retracted to a point where there is no slack in the belt, pull the belt to check that it cannot be extended.
Page 44 1-1. For safe use Removing a child restraint installed with a seat belt Push the buckle release button and fully retract the seat belt. Child restraint systems with a top tether strap Secure the child restraint sys- tem using the seat belt or LATCH anchors.
Page 45 1-1. For safe use WARNING ■ When installing a booster seat To prevent the belt from going into ALR lock mode, do not fully extend the shoulder belt. ALR mode causes the belt to tighten only. This could cause injury or discomfort to the child. (P. 30) ■...
Page 46 1-1. For safe use WARNING ■ When installing a child restraint system ● When a booster seat is installed, always ensure that the shoulder belt is positioned across the center of the child’s shoulder. The belt should be kept away from the child’s neck, but not so that it could fall off the child’s shoulder.
Page 47 Keep the trunk lid closed. ● If you smell exhaust gases in the vehicle even when the trunk lid is closed, open the windows and have the vehicle inspected at your Toyota dealer as soon as possible. ■ When parking ●...
Page 48 1-2. Theft deterrent system Engine immobilizer system The vehicle’s keys have built-in transponder chips that prevent the engine from starting if a key has not been previously regis- tered in the vehicle’s on-board computer. Never leave the keys inside the vehicle when you leave the vehi- cle.
Page 49 1-2. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type engine immobilizer system. ■ Conditions that may cause the system to malfunction ● If the grip portion of the key is in contact with a metallic object ●...
Page 50 1-2. Theft deterrent system  Alarm The alarm The alarm uses light and sound to give an alert when an intrusion is detected. The alarm is triggered in the following situations when the alarm is set: ● A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.
Page 51 1-2. Theft deterrent system ■ System maintenance The vehicle has a maintenance-free type alarm system. ■ Items to check before locking the vehicle To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following: ● Nobody is in the vehicle. ●...
Page 52 2. Instrument cluster Warning lights and indicators The warning lights and indicators on the instrument cluster and center panel inform the driver of the status of the vehicle’s vari- ous systems. For the purpose of explanation, the following illustration dis- plays all warning lights and indicators illuminated.
Page 53 2. Instrument cluster Warning lights Warning lights inform the driver of malfunctions in the indicated vehi- cle’s systems. Brake system warning ABS warning light light (P. 446) (P. 447) (U.S.A.) (Canada) Electric power steering Brake system warning system warning light light (P.
Page 54 There may be a mal- function in a system if a light does not come on, or if the lights do not turn off. Have the vehicle inspected by your Toyota dealer. : If equipped : The light comes on in yellow to indicate a malfunction.
Page 55 2. Instrument cluster Indicators The indicators inform the driver of the operating state of the vehicle’s various systems. 2, 5 Turn signal indicator Radar cruise control (P. 166) indicator (P. 188) 2, 4 Headlight indicator Cruise control “SET” (P. 168) indicator (P.
Page 56 Have the vehicle inspected by your Toyota dealer immedi- ately if this occurs.
Page 57 2. Instrument cluster Gauges and meters Vehicles without a multi-information display  Tachometer Displays the engine speed in revolutions per minute. Speedometer Fuel gauge Average fuel consumption meter Display change button P. 79 Odometer/trip meter/average fuel consumption display/set speed P. 79, 183 Engine coolant temperature display/meter light control display Displays the engine coolant temperature and meter light control.
Page 58 2. Instrument cluster Vehicles with a multi-information display  Tachometer Displays the engine speed in revolutions per minute. Multi-information display Presents the driver with a variety of driving-related data. Displays warning messages in case of a malfunction (P. 456) Outside temperature display Displays the outside temperature within the range of -40°F (-40°C) to 122°F (50°C).
Page 59 2. Instrument cluster Changing the odometer/trip meter display Pressing the display change but- Without a multi-information display  ton changes the display as fol- lows. With a multi-information display  Odometer ■ Displays the total distance the vehicle has been driven. Trip meter A /trip meter B ■...
Page 60 2. Instrument cluster Instrument panel lights control button The brightness of the Instrument panel lights can be adjusted. Pressing the button will adjust Without a multi-information display  brightness of the Instrument panel lights. With a multi-information display  Eco Driving Indicator Light customization (vehicles without a multi-information display) Eco Driving Indicator Light can be activated or deactivated.
Page 61 2. Instrument cluster ■ Eco driving indicator light During Eco-friendly acceleration (Eco Without a multi-information display  driving), Eco Driving Indicator Light will turn on. When the acceleration exceeds the Eco driving accelerator upper limit, or the vehicle is stopped, the light turns off. Eco Driving Indicator Light will not operate in the following conditions: ●...
Page 62 2. Instrument cluster NOTICE ■ To prevent damage to the engine and its components ● Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. ● Vehicle without a multi-information display: The engine may be overheat- ing if the rightmost segment of the engine coolant temperature display is flashing.
Page 63 2. Instrument cluster Multi-information display (if equipped) Display contents The multi-information display presents the driver with a variety of vehi- cle data. ● Menu icons Displays the following informa- tion when an icon is selected. (P. 84) Some of the information may be displayed automatically depending on the situation.
Page 64 2. Instrument cluster Warning message display Select to display warning messages and measures to be taken if a malfunction is detected. (P. 456) Settings display Select to change the meter display settings. (P. 86) Operating the meter control switches ■ Scroll up/down the screen and move up/down the cur- Switch menu/Displays the...
Page 65: Drive Information
2. Instrument cluster Drive information 1, 2 ● Average fuel economy /Tank average fuel economy /Trip aver- age fuel economy Displays the average fuel consumption since the function was reset, the vehicle was refueled, and the engine was started, respec- tively Use the displayed average fuel consumption as a reference.
Page 66 2. Instrument cluster Settings display Changing the settings ■ Select using the meter control switch. Select an item and then set it with the center button. Customizable items ■ ● Language Select to change the language on the display. ● Units Select to change the unit of measure for fuel consumption.
Page 67 2. Instrument cluster ● Maintenance system (U.S.A.) Select to reset the message after the required maintenance is  performed. ( P. 381) ● Initialization Registered or changed meter settings will be deleted or returned to their default setting. : Speed limit display may not be available for some regions. ■...
Page 68 2. Instrument cluster WARNING ■ The information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the display monitor may respond slowly, and display changes may be delayed. For example, there is a lag between the driver’s shifting and the new gear number appearing on the display.
Page 69 2. Instrument cluster Fuel consumption information Fuel consumption information can be displayed on the Entune Audio system and/or the navigation system. Entune Audio system or naviga- tion system CTY20BJ045 Trip information Entune Audio system with “CAR” button  Press the “CAR” button. If the “Past Record”...
Page 70 2. Instrument cluster Resetting the consumption data Average vehicle speed since the engine was started Elapsed time since the engine was started Fuel consumption in the past 15 minutes Cruising range (P. 91) Vehicles without a smart key system: Average fuel consumption for the past 15 minutes is divided by color into past averages and averages attained since the engine switch was last turned to the “ON”...
Page 71 2. Instrument cluster Past record Entune Audio system with “CAR” button  Press the “CAR” button. If the “Trip Information” screen is displayed, select “Past Record”. Entune Audio system or navigation system with “APPS” button  Press the “APPS” button. Touch “Eco”...
Page 72 2. Instrument cluster CAMRY_U (OM33A86U)
Page 73 3-1. Key information Keys The keys The following keys are provided with the vehicle. Vehicles without a smart key system (type A)  Master keys Operating the wireless remote con- trol function (P. 95) Valet key Key number plate Vehicles without a smart key system (type B) ...
Page 74 Opens the driver’s window and moon roof (if equipped) (P. 101) Opens the trunk (P. 110) : This setting must be customized at your Toyota dealer. Vehicles without a smart key system (type B)  Locks all the doors (P. 101) Unlocks all the doors (P.
Page 75 (P. 101) Opens the trunk (P. 110) Sounds the alarm (P. 97) : This setting must be customized at your Toyota dealer. Using the mechanical key (vehicles with a smart key system) To take out the mechanical key, push the release button and take the key out.
Page 76 ■ If you lose your keys New genuine keys can be made by your Toyota dealer using the other key (vehicles without a smart key system) or the other mechanical key (vehicles with a smart key system) and the key number stamped on your key number plate.
Page 77 3-1. Key information ■ Conditions affecting operation Vehicles without a smart key system  The wireless remote control function may not operate normally in the follow- ing situations: ● When the wireless key battery is depleted ● Near a TV tower, electric power plant, gas station, radio station, large dis- play, airport or other facility that generates strong radio waves or electrical noise ●...
Page 78 If a wrong key is used (vehicles with a smart key system) The key cylinder rotates freely to isolate inside mechanism. ■ Customization that can be configured at Toyota dealer Settings (e. g. smart key system) can be changed. (Customizable features: P. 525) ■...
Page 79 When an electronic key is lost (vehicles with a smart key system) If the electronic key remains lost, the risk of vehicle theft increases signifi- cantly. Visit your Toyota dealer immediately with all remaining electronic keys that were provided with your vehicle.
Page 80 Pressing the but- ton again within 5 seconds unlocks the other doors. Press and hold to open the Type B  driver’s window and moon roof. (P. 134, 137) : This setting must be customized at your Toyota dealer. CAMRY_U (OM33A86U)
Page 81 Press and hold to open the driver’s window and moon roof. (P. 134, 137) : This setting must be customized at your Toyota dealer. ◆ Turning the key operates the doors as follows: Vehicles without a smart key system ...
Page 82 3-2. Opening, closing and locking the doors ■ Operation signals Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice) Driver’s window and moon roof: A buzzer sounds to indicate that the driver’s window and moon roof are open- ing.
Page 83 3-2. Opening, closing and locking the doors Unlocking and locking the doors from the inside ◆ Door lock switches Locks all the doors Unlocks all the doors ◆ Inside lock buttons Locks the door Unlocks the door The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Page 84 3-2. Opening, closing and locking the doors Rear door child-protector lock The door cannot be opened from inside the vehicle when the lock is set. Unlock Lock These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
Page 85 3-2. Opening, closing and locking the doors Setting and canceling the functions ■ The automatic door locking and unlocking functions can be set or canceled on the audio system screen (P. 525) or by following the procedure below. Vehicles without a smart key system: Close all the doors and switch the engine switch to the “ON”...
Page 86 3-2. Opening, closing and locking the doors ■ Switching the door unlock function (vehicles with a smart key system) It is possible to set which doors the entry function unlocks using the wireless remote control. Turn the engine switch off. When the indicator light on the key surface is not on, press and hold for approximately 5 seconds while pressing and holding The setting changes each time an operation is performed, as shown below.
Page 87 3-2. Opening, closing and locking the doors WARNING ■ To prevent an accident Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury. ●...
Page 88 3-2. Opening, closing and locking the doors Trunk The trunk can be opened using the trunk opener, entry function, wireless remote control. Opening the trunk from inside the vehicle Pull up the lever to release the trunk lid. Opening the trunk from outside the vehicle ◆...
Page 89 3-2. Opening, closing and locking the doors ◆ Wireless remote control Vehicles without a smart key system  Press and hold the switch. Type A  Type B  Vehicles with a smart key system  Press and hold the switch. CAMRY_U (OM33A86U)
Page 90 3-2. Opening, closing and locking the doors ■ Operation signal A buzzer sounds to indicate that the trunk has been opened. ■ Trunk light The trunk light turns on when the trunk is opened. ■ Function to prevent the trunk being locked with the electronic key inside (vehicles with a smart key system) ●...
Page 91 3-2. Opening, closing and locking the doors WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ Before driving ● Make sure that the trunk lid is fully closed. If the trunk lid is not fully closed, it may open unexpectedly while driving and hit near-by objects or luggage in the trunk may be thrown out, causing an accident.
Page 92 ● Do not attach any accessories other than genuine Toyota parts to the trunk lid. Such additional weight on the trunk lid may cause the lid to suddenly shut again after it is opened.
Page 93 3-2. Opening, closing and locking the doors  Smart key system The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.) ● Locks and unlocks the doors (P. 101) ●...
Page 94 3-2. Opening, closing and locking the doors ■ Effective range (areas within which the electronic key is detected) When locking or unlocking the doors The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front outside door handles.
Page 95 3-2. Opening, closing and locking the doors Alarm Situation Correction procedure An attempt was made to lock either front door by opening a door and Interior alarm pings Retrieve the electronic putting the inside lock once and exterior alarm key from the vehicle button into the lock sounds once for 5 sec- and lock the doors...
Page 96 3-2. Opening, closing and locking the doors ■ Electronic Key Battery-Saving Function When battery-saving mode is set, battery depletion is minimized by stopping the electronic key from receiving radio waves. Press twice while pressing and holding . Confirm that the electronic key indicator flashes 4 times.
Page 97 3-2. Opening, closing and locking the doors ■ Note for the entry function ● Even when the electronic key is within the effective range (detection areas), the system may not operate properly in the following cases: • The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
Page 98 3-2. Opening, closing and locking the doors ● If the electronic key is inside the vehicle and a door handle becomes wet during a car wash, a message may be shown on the multi-information dis- play and a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
Page 99 (P. 114) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of the emitted radio waves.
Page 100 3-3. Adjusting the seats Front seats Adjustment procedure Manual seat  Seat position adjustment lever Vertical height adjustment lever (driver’s side only) Seatback angle adjustment lever Power seat  Seat position adjustment Vertical height adjustment switch switch (driver’s side only) Seatback angle adjustment Lumbar support adjustment switch...
Page 101 3-3. Adjusting the seats WARNING ■ When adjusting the seat position ● Take care when adjusting the seat position to ensure that other passen- gers are not injured by the moving seat. ● Do not put your hands under the seat or near the moving parts to avoid injury.
Page 102 3-3. Adjusting the seats Rear seats The seatbacks of the rear seats can be folded down. Folding down the rear seatbacks Pull the seatback lever in the trunk for the seatback you wish to fold down. CAMRY_U (OM33A86U)
Page 103 3-3. Adjusting the seats WARNING ■ When folding the rear seatbacks down Observe the following precautions. Failure to do so may result in death or serious injury. ● Do not fold the seatbacks down while driving. ● Stop the vehicle on level ground, set the parking brake and shift the shift lever to P.
Page 104 3-3. Adjusting the seats Head restraints Head restraints are provided for all seats. Front seats Vertical adjustment Pull the head restraint up. Down Push the head restraint down while pressing the lock release button. Lock release button ■ Removing the head restraints (front seats) Pull the head restraint up while pressing the lock release button.
Page 105 3-3. Adjusting the seats ■ Adjusting the height of the head restraints (front seats) Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears. WARNING ■ Head restraint precautions (front seats) Observe the following precautions regarding the head restraints.
Page 106 3-4. Adjusting the steering wheel and mirrors Steering wheel Adjustment procedure Hold the steering wheel and push the lever down. Adjust to the ideal position by moving the steering wheel hori- zontally and vertically. After adjustment, pull the lever up to secure the steering wheel.
Page 107 3-4. Adjusting the steering wheel and mirrors WARNING ■ Caution while driving Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci- dent, resulting in death or serious injury. ■...
Page 108 3-4. Adjusting the steering wheel and mirrors Inside rear view mirror The rear view mirror’s position can be adjusted to enable suffi- cient confirmation of the rear view. Adjusting the height of rear view mirror The height of the rear view mirror can be adjusted to suit your driving posture.
Page 109 3-4. Adjusting the steering wheel and mirrors Auto anti-glare inside rear view mirror  Responding to the level of brightness of the headlights of vehicles behind, the reflected light is automatically reduced. Changing automatic anti-glare function mode On/off When the automatic anti-glare function is in ON mode, the indica- tor illuminates.
Page 110 3-4. Adjusting the steering wheel and mirrors Outside rear view mirrors Adjustment procedure To select a mirror to adjust, press the switch. Left Right To adjust the mirror, press the switch. Right Down Left Folding the mirrors Push the mirror back in the direc- tion of the vehicle’s rear.
Page 111 3-4. Adjusting the steering wheel and mirrors ■ Mirror angle can be adjusted when Vehicles without a smart key system  The engine switch is in the “ACC” or “ON” position. Vehicles with a smart key system  The engine switch is in ACCESSORY or IGNITION ON mode. ■...
Page 112 3-5. Opening and closing the windows Power windows Opening and closing procedures The power windows can be opened and closed using the switches. Operating the switch moves the windows as follows: Closing One-touch closing (front side windows only) Opening One-touch opening (front side windows only) : To stop the window partway, oper- ate the switch in the opposite direc-...
Page 113 If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform- ing the above procedure correctly, have the vehicle inspected by your Toyota dealer. ■...
Page 114 3-5. Opening and closing the windows WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ Closing the windows ● The driver is responsible for all the power window operations, including the operation for the passengers. In order to prevent accidental operation, especially by a child, do not let a child operate the power windows.
Page 115 3-5. Opening and closing the windows  Moon roof Use the overhead switches to open and close the moon roof and tilt it up and down. Opening and closing Opens the moon roof The moon roof stops slightly before the fully open position to reduce wind noise.
Page 116 3-5. Opening and closing the windows ■ The moon roof can be operated when Vehicles without a smart key system  The engine switch is in the “ON” position. Vehicles with a smart key system  The engine switch is in IGNITION ON mode. ■...
Page 117 Check to make sure that the moon roof is completely closed and then release the switch. If the moon roof does not fully close even after performing the above proce- dure correctly, have the vehicle inspected by your Toyota dealer. ■ Moon roof open warning buzzer...
Page 118 3-5. Opening and closing the windows WARNING Observe the following precautions. Failure to do so may cause death or serious injury. ■ Opening the moon roof ● Do not allow any passengers to put their hands or heads outside the vehi- cle while it is moving.
Page 119 3-5. Opening and closing the windows CAMRY_U (OM33A86U)
Page 120 4-1. Before driving Driving the vehicle The following procedures should be observed to ensure safe driving: Starting the engine P. 155, 157 Driving With the brake pedal depressed, shift the shift lever to D. (P. 162) Release the parking brake. (P. 167) Gradually release the brake pedal and gently depress the accelera- tor pedal to accelerate the vehicle.
Page 121 Your vehicle has a drum-in-disc type parking brake system. This type of brake system needs bedding-down of the brake shoes periodically or whenever the parking brake shoes and/or drum are replaced. Have your Toyota dealer per- form the bedding down operation.
Page 122 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When starting the vehicle Always keep your foot on the brake pedal while stopped with the engine running. This prevents the vehicle from creeping. ■...
Page 123 If you hear a squealing or scraping noise (brake pad wear limit indica- tors) Have the brake pads checked and replaced by your Toyota dealer as soon as possible. Rotor damage may result if the pads are not replaced when needed.
Page 124 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When the vehicle is stopped ● Do not race the engine. If the shift lever is any position other than P or N, the vehicle may acceler- ate suddenly and unexpectedly, causing an accident.
Page 125 4-1. Before driving WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When the vehicle is parked ● Always apply the parking brake, shift the shift lever to P, stop the engine and lock the vehicle.
Page 126 Short in electrical components ● Engine damage caused by water immersion In the event that you drive on a flooded road and the vehicle is flooded, be sure to have your Toyota dealer check the following: ● Brake function ●...
Page 127 Consult this manual to determine how this reduces the available cargo and luggage load capacity of your vehicle. (P. 152) Toyota does not recommend towing a trailer with your vehicle. Your vehicle is not designed for trailer towing. CAMRY_U (OM33A86U)
Page 128 4-1. Before driving Calculation formula for your vehicle Cargo capacity Total load capacity (vehicle capacity weight) (P. 500) When 2 people with the combined weight of A lb. (kg) are riding in your vehicle, which has a total load capacity (vehicle capacity weight) of B lb.
Page 129 4-1. Before driving WARNING ■ Things that must not be carried in the trunk The following things may cause a fire if loaded in the trunk: ● Receptacles containing gasoline ● Aerosol cans ■ Storage precautions Observe the following precautions. Failure to do so may prevent the pedals from being depressed properly, may block the driver’s vision, or may result in items hitting the driver or passengers, possibly causing an accident.
Page 130 Seating capacity means the maximum number of occupants whose estimated average weight is 150 lb. (68 kg) per person. ◆ Towing capacity Toyota does not recommend towing a trailer with your vehicle. ◆ Cargo capacity Cargo capacity may increase or decrease depending on the weight and the number of occupants.
Page 131 Trailer towing Toyota does not recommend towing a trailer with your vehicle. Toyota also does not recommend the installation of a tow hitch or the use of a tow hitch carrier for a wheelchair, scooter, bicy- cle, etc. Your vehicle is not designed for trailer towing or for the use of tow hitch mounted carriers.
Page 132 4-1. Before driving Dinghy towing Your vehicle is not designed to be dinghy towed (with 4 wheels on the ground) behind a motor home. NOTICE ■ To avoid serious damage to your vehicle Do not tow your vehicle with four wheels on the ground. CAMRY_U (OM33A86U)
Page 133 4-2. Driving procedures Engine (ignition) switch (vehicles without a smart key system) Starting the engine Check that the parking brake is set. Check that the shift lever is in P. Firmly depress the brake pedal. Turn the engine switch to the “START” position and start the engine.
Page 134 Do not crank the engine for more than 30 seconds at a time. This may overheat the starter and wiring system. ● Do not race a cold engine. ● If the engine becomes difficult to start or stalls frequently, have your vehi- cle checked by your Toyota dealer immediately. CAMRY_U (OM33A86U)
Page 135 4-2. Driving procedures Engine (ignition) switch (vehicles with a smart key system) Performing the following operations when carrying the elec- tronic key on your person starts the engine or changes engine switch modes. Starting the engine Check that the parking brake is set. Check that the shift lever is in P.
Page 136 4-2. Driving procedures Changing engine switch modes Modes can be changed by pressing the engine switch with the brake pedal released. (The mode changes each time the switch is pressed.) The emergency flashers can be used. The multi-information display will not be displayed.
Page 137 If the engine does not start ● The engine immobilizer system may not have been deactivated. (P. 67) Contact your Toyota dealer. ● Check that the shift lever is securely set in P. The engine may not start if the shift lever is displaced out of P.
Page 138 4-2. Driving procedures ■ If the electronic key battery is depleted P. 420 ■ Operation of the engine switch ● When operating the engine switch, one short, firm press is enough. If the switch is pressed improperly, the engine may not start or the engine switch mode may not change.
Page 139 Do not race a cold engine. ● If the engine becomes difficult to start or stalls frequently, have your vehi- cle checked by your Toyota dealer immediately. ■ Symptoms indicating a malfunction with the engine switch If the engine switch seems to be operating somewhat differently than usual, such as the switch sticking slightly, there may be a malfunction.
Page 140 4-2. Driving procedures Automatic transmission Shifting the shift lever Vehicles without a smart key system: While the engine switch is in the “ON” position, move the shift lever with the brake pedal depressed. Vehicles with a smart key system: While the engine switch is in IGNITION ON mode, move the shift lever with the brake pedal depressed.
Page 141 4-2. Driving procedures Changing shift ranges in S mode When the shift lever is in the S position, the shift lever or paddle shift switches (if equipped) can be operated as follows: Shift lever Paddle shift switches   equipped) Upshifting Downshifting The initial shift range in S mode is set automatically to 4 or 5 accord-...
Page 142 4-2. Driving procedures Selecting shift ranges in the D position (vehicles with paddle shift switches) To drive using temporary shift range selection, operate the “-” paddle shift switch. The shift range can then be selected by operating the “-” and “+” paddle shift switches. Changing the shift range allows restric- tion of the highest gear, preventing upshifting and enabling the level of engine braking force to be selected.
Page 143 S This may indicate a malfunction in the automatic transmission system. Have the vehicle inspected by your Toyota dealer immediately. (In this situation, the transmission will operate in the same manner as when the shift lever is in D.) ■...
Page 144 4-2. Driving procedures Turn signal lever Operating instructions Right turn Lane change to the right (move the lever partway and release The right hand signals will flash 3 times. Lane change to the left (move the lever partway and release The left hand signals will flash 3 times.
Page 145 4-2. Driving procedures Parking brake Operating instructions To set the parking brake, fully depress the parking brake pedal with your left foot while depress- U.S.A. Canada ing the brake pedal with your right foot. (Depressing pedal again releases the parking brake.) ■...
Page 146 4-3. Operating the lights and wipers Headlight switch The headlights can be operated manually or automatically. Operating instructions Turning the end of the lever turns on the lights as follows: The headlights, day- time running lights and lights listed below turn on and off automatically.
Page 147 4-3. Operating the lights and wipers Turning on the high beam headlights With the headlights on, push the lever away from you to turn on the high beams. Pull the lever toward you to the center position to turn the high beams off.
Page 148 4-3. Operating the lights and wipers ■ Automatic light off system Vehicles without a smart key system  ● When the headlights are on: The headlights and tail lights turn off 30 sec- onds after the engine switch is turned to the “ACC” or “LOCK” position and a door is opened and closed.
Page 149 4-3. Operating the lights and wipers ■ Battery-saving function In the following conditions, the remaining lights will go off automatically after 20 minutes in order to prevent the vehicle battery from being discharged: ● The headlights and/or tail lights are on. ●...
Page 150 4-3. Operating the lights and wipers  Automatic High Beam The Automatic High Beam uses an in-vehicle camera sensor to assess the brightness of streetlights, the lights of oncoming and preceding vehicles, etc., and automatically turns high beam on or off as necessary. Activating the Automatic High Beam system Turn the headlight switch to Push the lever away from you.
Page 151 4-3. Operating the lights and wipers High beam automatic turning on or off conditions When all of the following conditions are fulfilled, high beam will be automatically turned on: ● Vehicle speed is above approximately 21 mph (34 km/h). ● The area ahead of the vehicle is dark. ●...
Page 152 4-3. Operating the lights and wipers ■ The Automatic High Beam can be operated when The engine switch is in IGNITION ON mode. ■ Camera sensor detection information ● High beam may not be automatically turned off in the following situations: •...
Page 153 4-3. Operating the lights and wipers ● In the situations below, the system may not be able to correctly detect the surrounding brightness levels, and may flash or expose nearby pedestrians to the high beam. Therefore, you should consider turning the high beams on or off manually rather than relying on the Automatic High Beam system.
Page 154 4-3. Operating the lights and wipers ■ If the Automatic High Beam indicator flashes It may indicate a malfunction in the system. Contact your Toyota dealer. ■ Customization The Automatic High Beam can be deactivated. (Customizable features: P. 531) WARNING ■...
Page 155 Do not install a parking tag or any other accessories near or around the camera sensor. ● Do not overload the vehicle. ● Do not modify the vehicle. ● If the windshield needs to be replaced, contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 156 4-3. Operating the lights and wipers Windshield wipers and washer Operating the wiper lever The wiper operation is selected by moving the lever as follows. When intermittent windshield wiper operation is selected, the wiper interval can be also adjusted. Intermittent windshield wiper operation Low speed windshield...
Page 157 Damage to the washer fluid pump may be caused if the lever is pulled toward you and held continually. ■ When a nozzle becomes blocked In this case, contact your Toyota dealer. Do not try to clear it with a pin or other object. The nozzle will be damaged. CAMRY_U (OM33A86U)
Page 158 4-4. Refueling Opening the fuel tank cap Perform the following steps to open the fuel tank cap: Before refueling the vehicle ● Close all the doors and windows, and turn the engine switch off. ● Confirm the type of fuel. ■...
Page 159 4-4. Refueling NOTICE ■ Refueling Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the emission control system to operate abnormally or damaging fuel system components or the vehicle’s painted surface. Opening the fuel tank cap Pull up the opener to open the fuel filler door.
Page 160 WARNING ■ When replacing the fuel tank cap Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
Page 161 4-5. Using the driving support systems  Cruise control Summary of functions Use the cruise control to maintain a set speed without depressing the accelerator pedal. Vehicles without a multi-infor- Vehicles with a multi-informa-   mation display tion display Display Set speed Indicators...
Page 162 4-5. Using the driving support systems Setting the vehicle speed Press the “ON-OFF” button to activate the cruise control. Vehicles without a multi-informa- tion display Cruise control indicator will come Vehicles with a multi-information display Cruise control indicator will be dis- played on the multi-information dis- play.
Page 163 4-5. Using the driving support systems Adjusting the set speed To change the set speed, operate the lever until the desired set speed is obtained. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direc- tion.
Page 164 If the cruise control speed cannot be set or if the cruise control cancels imme- diately after being activated, there may be a malfunction in the cruise control system. Have the vehicle inspected by your Toyota dealer. CAMRY_U (OM33A86U)
Page 165 4-5. Using the driving support systems WARNING ■ To avoid operating the cruise control by mistake Switch the cruise control off using the “ON-OFF” button when not in use. ■ Situations unsuitable for cruise control Do not use cruise control in any of the following situations. Doing so may result in loss of control and could cause an accident resulting in death or serious injury.
Page 166 4-5. Using the driving support systems  Dynamic radar cruise control Summary of functions Dynamic radar cruise control supplements conventional cruise control with a vehicle-to-vehicle distance control. In vehicle-to-vehicle dis- tance control mode, the vehicle automatically accelerates or deceler- ates in order to maintain a set following distance from vehicles ahead. Vehicle-to-vehicle distance but- Indicators Set speed...
Page 167 4-5. Using the driving support systems Setting the vehicle speed (vehicle-to-vehicle distance control mode) Press the “ON-OFF” button to activate the cruise control. Radar cruise control indicator will be displayed. Press the button again to deacti- vate the cruise control. Accelerate or decelerate the vehicle to the desired speed, and push the lever down to set...
Page 168 4-5. Using the driving support systems Adjusting the set speed To change the set speed, operate the lever until the desired set speed is displayed. Increases the speed Decreases the speed Fine adjustment: Momentarily move the lever in the desired direc- tion.
Page 169 4-5. Using the driving support systems Changing the vehicle-to-vehicle distance Pressing the button changes the Preceding vehicle-to-vehicle distance as fol- vehicle mark lows: Long Medium Short Preceding vehicle mark The vehicle-to-vehicle distance is set automatically to long mode when the engine switch is turned to IGNITION ON mode.
Page 170 4-5. Using the driving support systems Driving in vehicle-to-vehicle distance control mode This mode employs a radar sensor to detect the presence of vehicles up to approximately 400 ft. (120 m) ahead, determines the current vehicle-to-vehicle following distance, and operates to maintain a suit- able following distance from the vehicle ahead.
Page 171 4-5. Using the driving support systems Example of follow-up cruising When following a vehicle driving slower than the set speed The system continues follow-up cruising while adjusting for changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle dis- tance set by the driver.
Page 172 4-5. Using the driving support systems Selecting conventional constant speed control mode When constant speed control mode is selected, your vehicle will main- tain a set speed without controlling the vehicle-to-vehicle distance. Select this mode only when vehicle-to-vehicle distance control mode does not function correctly due to dirt etc.
Page 173 The windshield wipers are operating at high speed (when the wiper switch is set to the high speed wiper operation position). If vehicle-to-vehicle distance control driving is automatically canceled for any other reason, there may be a malfunction in the system. Contact your Toyota dealer. ■...
Page 174 4-5. Using the driving support systems ■ Radar sensor and grille cover Always keep the sensor and grille cover clean to ensure that the vehicle-to- vehicle distance control operates properly. (Some obstructions, such as snow, ice and plastic objects, cannot be detected by the obstruction sensor.) Dynamic radar cruise control is canceled if an obstruction is detected.
Page 175 4-5. Using the driving support systems WARNING ■ Before using dynamic radar cruise control Do not overly rely on vehicle-to-vehicle distance control. Be aware of the set speed. If automatic deceleration/acceleration is not appropriate, adjust the vehicle speed, as well as the distance between your vehicle and vehicles ahead by applying the brakes etc.
Page 176 4-5. Using the driving support systems WARNING ■ Situations unsuitable for dynamic radar cruise control Do not use dynamic radar cruise control in any of the following situations. Doing so may result in inappropriate speed control and could cause an acci- dent resulting in death or serious injury.
Page 177 4-5. Using the driving support systems WARNING ● Motorcycles traveling in the same lane ● When water or snow thrown up by the surrounding vehicles hinders the detecting of the sensor ● When your vehicle is pointing upwards (caused by a heavy load in the trunk, etc.) ■...
Page 178 Do not attach accessories or stickers to the sensor, grille cover or sur- rounding area. ● Do not modify or paint the sensor and grille cover. ● If the radar sensor needs to be replaced, contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 179 4-5. Using the driving support systems  LDA (Lane Departure Alert) Summary of function While driving on a road that has lane markers, this system recognizes the lane markers using a camera as a sensor to alert the driver when the vehicle deviates from its lane.
Page 180 4-5. Using the driving support systems Operating conditions ● When the vehicle speed is approximately 32 mph (50 km/h) or more ● When the lane width is more than approximately 8.2 ft. (2.5 m) ● When driving on a straight road or through a curve with a radius of more than approximately 328 ft.
Page 181 4-5. Using the driving support systems ■ Temporary cancelation of the LDA system functions If any of the following occurs, the LDA system functions will be temporarily canceled. The functions will resume after the necessary operating conditions have returned. ● The turn signal lever is operated.
Page 182 4-5. Using the driving support systems ■ Conditions in which the function may not operate correctly In the following situations, the camera sensor may be unable to recognize lane markers causing the lane departure warning function to operate incor- rectly. However, this does not indicate a malfunction. ●...
Page 183 4-5. Using the driving support systems WARNING ■ Before using the LDA system Do not rely solely on the LDA system. The LDA system does not drive the vehicle automatically, nor does it reduce the amount of care you need to take.
Page 184 The direction of the camera sensor is precisely adjusted. ● Do not subject the camera sensor to strong impact or force, and do not disassemble the camera sensor. ● If the windshield needs to be replaced, contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 185 4-5. Using the driving support systems Rear view monitor system The rear view monitor system assists the driver by displaying guide lines and an image of the view behind the vehicle while backing up, for example while parking. The screen illustrations used in this text are intended as examples, and may differ from the image that is actually displayed on the screen.
Page 186 4-5. Using the driving support systems Using the rear view monitor system Screen description ■ Vehicle width guide lines The line indicates a guide path when the vehicle is being backed straight up. The displayed width is wider than the actual vehicle width. Vehicle center guide lines These lines indicate the estimated vehicle center on the ground.
Page 187 4-5. Using the driving support systems Rear view monitor system precautions Area displayed on screen ■ The rear view monitor system displays an image of the view from the bumper of the rear area of the vehicle. To adjust the image on the rear view monitor system screen.
Page 188 4-5. Using the driving support systems Differences between the screen and the actual road ■ The distance guide lines and the vehicle width guide lines may not actually be parallel with the dividing lines of the parking space, even when they appear to be so. Be sure to check visually. The distances between the vehicle width guide lines and the left and right dividing lines of the parking space may not be equal, even when they appear to be so.
Page 189 4-5. Using the driving support systems ● When any part of the vehicle sags When any part of the vehicle sags due to the number of pas- sengers or the distribution of the load, there is a margin of error between the fixed guide lines on the screen and the actual distance/course on the A margin of error...
Page 190 4-5. Using the driving support systems Vehicle width guide lines ■ Visually check the surroundings and the area behind the vehicle. In the case shown below, the truck appears to be outside of the vehi- cle width guide lines and the vehicle does not look as if it hits the truck.
Page 191 If you notice any of the following symptoms, refer to the likely cause and the solution, and re-check. If the symptom is not resolved by the solution, have the vehicle inspected by your Toyota dealer. Likely cause Solution  The image is difficult to see •...
Page 192 4-5. Using the driving support systems WARNING ■ When using the rear view monitor system The rear view monitor system is a supplemental device intended to assist the driver when backing up. When backing up, be sure to check visually behind and all around the vehicle before proceeding.
Page 193 ● Do not expose the camera to strong impact as this could cause a malfunc- tion. If this happens, have the vehicle inspected by your Toyota dealer as soon as possible. CAMRY_U (OM33A86U)
Page 194 4-5. Using the driving support systems Driving assist systems To help enhance driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supple- mentary and should not be relied upon too heavily when operat- ing the vehicle.
Page 195 4-5. Using the driving support systems When the TRAC/VSC systems are operating The slip indicator light will flash while the TRAC/VSC systems are operating. Disabling the TRAC system If the vehicle gets stuck in mud, dirt or snow, the TRAC system may reduce power from the engine to the wheels.
Page 196 When the “TRAC OFF” indicator light comes on even if the has not been pressed (vehicles without a multi-information display) TRAC cannot be operated. Contact your Toyota dealer. ■ When the message is displayed on the multi-information display show- ing that TRAC has been disabled even if...
Page 197 4-5. Using the driving support systems ■ Automatic reactivation of TRAC and VSC systems After turning the TRAC and VSC systems off, the systems will be automati- cally re-enabled in the following situations: ● When the engine switch is turned off ●...
Page 198 The ABS, TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels. ■ Handling of tires and the suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.
Page 199 4-5. Using the driving support systems  PCS (Pre-Collision System) When the radar sensor detects possibility of a frontal collision, brakes are automatically engaged to lessen impact as well as vehicle damage. The alert timing for the pre-collision system can be changed or turned on/off, as necessary, by operating the switch.
Page 200 4-5. Using the driving support systems Changing the pre-collision system Changing the alert timing of the pre-collision system ■ Each time the PCS switch is pressed, the response to the distance changes as follows. Middle Near : Default setting Turning off the pre-collision system ■...
Page 201 4-5. Using the driving support systems ■ The pre-collision system is operational when The pre-collision system is on (P. 222) and the following conditions are met: ● Pre-collision warning: • Vehicle speed is greater than approximately 10 mph (15 km/h). •...
Page 202 4-5. Using the driving support systems ■ Obstacles not detected The sensor cannot detect plastic obstacles such as traffic cones. There may also be occasions when the sensor cannot detect pedestrians, animals, bicy- cles, motorcycles, trees, or snowdrifts. ■ Situations in which the pre-collision system does not function properly The system may not function effectively in situations such as the following: ●...
Page 203 4-5. Using the driving support systems ■ Certification For vehicles sold in the U.S.A.  FCC ID : HYQDNMWR007 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 204 Do not attach accessories or stickers to the sensor, grille cover or sur- rounding area. ● Do not modify or paint the sensor and grille cover. ● If the radar sensor needs to be replaced, contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 205 4-5. Using the driving support systems WARNING ■ Cautions regarding the assist contents of the system By means of alarms and brake control, the pre-collision system is intended to assist the driver in avoiding collisions through the process of LOOK- JUDGE-ACT.
Page 206 4-5. Using the driving support systems  BSM (Blind Spot Monitor) Summary of the Blind Spot Monitor The Blind Spot Monitor is a system that has 2 functions; ● The Blind Spot Monitor function Assists the driver in making the decision when changing lanes ●...
Page 207 4-5. Using the driving support systems Rear Cross Traffic Alert buzzer (Rear Cross Traffic Alert function only) When a vehicle approaching from the right or left rear of the vehicle is detected, a buzzer sounds from behind the rear seat. ■...
Page 208 If the sensor moves even slightly off position, the system may mal- function and vehicles that enter the detection area may not be detected. If the sensor or surrounding area is subject to a strong impact, always have the area inspected by your Toyota dealer. ● Do not disassemble the sensor.
Page 209 4-5. Using the driving support systems The Blind Spot Monitor function The Blind Spot Monitor function uses radar sensors to detect vehicles that are traveling in an adjacent lane in the area that is not reflected in the outside rear view mirror (the blind spot), and advises the driver of the vehicles existence via the outside rear view mirror indicator.
Page 210 4-5. Using the driving support systems ■ Conditions under which the Blind Spot Monitor function will not detect a vehicle The Blind Spot Monitor function is not designed to detect the following types of vehicles and/or objects: ● Small motorcycles, bicycles, pedestrians etc. ●...
Page 211 4-5. Using the driving support systems The Rear Cross Traffic Alert function The Rear Cross Traffic Alert functions when your vehicle is in reverse. It can detect other vehicles approaching from the right or left rear of the vehicle. It uses radar sensors to alert the driver of the other vehi- cle’s existence through flashing the outside rear view mirror indicators and sounding a buzzer.
Page 212 4-5. Using the driving support systems The Rear Cross Traffic Alert function detection areas The areas that vehicles can be detected in are outlined below. To give the driver a more consistent time to react, the buzzer can alert for faster vehicles from farther away. Example: Approximate Approaching vehicle...
Page 213 4-5. Using the driving support systems ■ Conditions under which the Rear Cross Traffic Alert function may not function correctly The Rear Cross Traffic Alert function may not detect vehicles correctly in the following conditions: ● When ice or mud etc. is attached to the rear bumper ●...
Page 214 4-6. Driving tips Winter driving tips Carry out the necessary preparations and inspections before driving the vehicle in winter. Always drive the vehicle in a man- ner appropriate to the prevailing weather conditions. Preparation for winter ● Use fluids that are appropriate to the prevailing outside tempera- tures.
Page 215 4-6. Driving tips When driving the vehicle Accelerate the vehicle slowly, keep a safe distance between you and the vehicle ahead, and drive at a reduced speed suitable to road con- ditions. When parking the vehicle Park the vehicle and move the shift lever to P without setting the park- ing brake.
Page 216 NOTICE ■ Repairing or replacing snow tires Request repairs or replacement of snow tires from Toyota dealers or legiti- mate tire retailers. This is because the removal and attachment of snow tires affects the opera- tion of the tire pressure warning valves and transmitters.
Page 217 4-6. Driving tips CAMRY_U (OM33A86U)
Page 218 5-1. Basic Operations Audio system types Entune Audio  Entune Audio Plus  Owners of this system should refer to the “NAVIGATION AND MULTI- MEDIA SYSTEM OWNER'S MANUAL”. CAMRY_U (OM33A86U)
Page 219 5-1. Basic Operations Entune Premium Audio with Navigation  Owners of this system should refer to the “NAVIGATION AND MULTI- MEDIA SYSTEM OWNER'S MANUAl”. CAMRY_U (OM33A86U)
Page 220 5-1. Basic Operations  Audio system Operations such as listening to audio, using the hands-free phone and changing multimedia system settings are started by using the following buttons. Audio system operation buttons “AUDIO” button Display the “Select Audio Source” screen or audio top screen. (P.
Page 221 5-1. Basic Operations Operating the touch screen By touching the screen with your finger, you can control the multime- dia system, etc. Drag ■ Touch the screen with your finger, and move the screen to the desired position. ● Scrolling the lists Flick ■...
Page 222 5-1. Basic Operations Steering wheel audio switches Some audio features can be controlled using the switches on the steering wheel. Operation may differ depending on the type of multimedia sys- tem or navigation system. For details, refer to the manual pro- vided with the multimedia system or navigation system.
Page 223 5-1. Basic Operations USB port/AUX port Connect an iPod, USB memory device or portable audio player to the USB/AUX port as indicated below. Select “iPod”, “USB” or “AUX” on the audio source selection screen and the device can be operated via multimedia system. Connecting using the USB/AUX port iPod ■...
Page 224 5-1. Basic Operations WARNING ■ While driving Do not connect a device or operate the device controls. CAMRY_U (OM33A86U)
Page 225 5-1. Basic Operations Basic audio operations Basic audio operations and functions common to each mode are explained in this section. Operating the multimedia system Press: Turns the multimedia system on and off. Turn: Adjusts the volume. Ejects a disc. Disc slot Pauses or resumes playing music.
Page 226 5-1. Basic Operations WARNING ■ Laser product This product is a class 1 laser product. Do not open the cover of the player or attempt to repair the unit yourself. Refer servicing to qualified personnel. ● Laser products • Do not take this unit apart or attempt to make any changes yourself. This is an intricate unit that uses a laser pickup to retrieve information from the surface of compact discs.
Page 227 5-2.Setup Setup menu You can adjust the multimedia system to your desired settings. Display “Setup” screen Press the “SETUP” button to display the “Setup” screen. Select to adjust the settings for operation sounds, screen ani- mation, etc. (P. 252) Select to set the voice settings. (P.
Page 228 The animation effect for the screen can be set to on/off. Select to delete personal data (P. 253) Select to update program versions. For details, contact your Toyota dealer. Select to display the software information. Notices related to third party software used in this product are enlisted. (This includes instructions for obtaining such software, where applicable.)
Page 229 5-2. Setup Delete personal data Select “Delete Personal Data” on the “General Settings” screen. Select “Delete”. Check carefully beforehand, as data cannot be retrieved once deleted. A confirmation screen will be displayed. Select “Yes”. The following personal data will be deleted or changed to its default settings.
Page 230 5-2. Setup Audio settings Settings are available for adjusting the radio operation, cover art, etc. Screen for audio settings Press the “SETUP” button. Select “Audio” on the “Setup” screen. Number of Radio Presets Select the number of radio preset stations. Display Cover Art on/off Automatic Sound Levelizer (P.
Page 231 5-2. Setup Display settings Settings are available for adjusting the contrast and brightness of the screen. Screen for display settings Press the “SETUP” button. Select “Display” on the “Setup” screen. Adjust screen contrast/bright- ness Adjust screen contrast/bright- ness of the rear view monitor camera Changes to day mode.
Page 232 5-2. Setup Voice settings This screen is used for guidance for voice command systems setting. Adjust the voice guidance vol- ume setting. voice recognition prompts “High”, “Low” or “Off”. Set the train voice recognition. Set the voice prompt interrupt on/off. Set the voice recognition tuto- rial.
Page 233 5-3.Using the Multimedia system Selecting the audio source Switching between audio sources such as radio and CD are explained in this section. Changing audio source Press the “AUDIO” button to display the audio source selection screen. If the audio source selection screen is not displayed, press the “AUDIO” button again.
Page 234 5-3. Using the Multimedia system List screen operation When a list screen is displayed, use the appropriate buttons to scroll through the list. How to scroll : Select to scroll to the next or previous page. : If appears to the right of titles, the complete titles are too long for the display.
Page 235 5-3. Using the Multimedia system Selecting a track/file/song from the track/file/song list ■ Select “Browse” or cover art. Select the desired track/file/ song. When an MP3/WMA/AAC disc or USB memory device is being used, ® the folder can be selected. When a Bluetooth device or iPod is being used, the album can be selected.
Page 236 5-3. Using the Multimedia system Optimal use of the multimedia system On the “Sound Settings” screen, sound quality (Treble/Mid/ Bass), volume balance can be adjusted. How to adjust the sound settings and sound quality Select “-” or “+” to adjust 1 2 3 the treble, mid or bass to a level between -5 and 5.
Page 237 5-4.Using the radio Radio operation Select “AM” or “FM” on the audio source selection screen to begin listening to the radio. Audio control screen Pressing the “AUDIO” button displays the audio control screen from any screens of the selected source. Audio source selection screen appears Preset stations...
Page 238 5-4. Using the radio Setting station presets Search for desired stations by turning the “TUNE/SCROLL” knob or pressing the “” or “” button on “SEEK/TRACK”. Select “(add new)”. To change the preset station to a different one, select and hold the preset station.
Page 239 ■ Error messages If an error message is displayed, refer to the following table and take the appropriate measures. If the problem is not rectified, take the vehicle to your Toyota dealer. Message Cause Correction procedures • The disc is dirty or •...
Page 240 5-5. Playing an audio CD and MP3/WMA/AAC discs ■ Discs that can be used Discs with the marks shown below can be used. Playback may not be possible depending on recording format or disc fea- tures, or due to scratches, dirt or deterioration. CDs with copy-protection features may not play correctly.
Page 241 5-5. Playing an audio CD and MP3/WMA/AAC discs ● WMA file compatibility • Compatible standards WMA Ver. 7, 8, 9 • Compatible sampling frequencies 32, 44.1, 48 (kHz) • Compatible bit rates (only compatible with 2-channel playback) Ver. 7, 8: CBR 48-192 (kbps) Ver.
Page 242 5-5. Playing an audio CD and MP3/WMA/AAC discs ● ID3, WMA and AAC tags ID3 tags can be added to MP3 files, making it possible to record the track title, artist name, etc. The system is compatible with ID3 Ver. 1.0, 1.1, and Ver. 2.2, 2.3 ID3 tags. (The number of characters is based on ID3 Ver.
Page 243 5-5. Playing an audio CD and MP3/WMA/AAC discs NOTICE ■ Discs and adapters that cannot be used Do not use the following types of CDs. Also, do not use 3 in. (8 cm) CD adapters, Dual Discs or printable discs. Doing so may damage the CD player and/or the CD insert/eject function.
Page 244 5-6.Using an external device Listening to an iPod Connecting an iPod enables you to enjoy music from the vehicle speakers. Select “iPod” on the audio source selection screen. When the iPod connected to the system includes iPod video, the system can only output the sound by selecting the browse screen.
Page 245 5-6. Using an external device ■ About iPod ● “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod or iPhone, respectively, and has been certified by the developer to meet Apple performance stan- dards.
Page 246 5-6. Using an external device ■ Error messages Message Cause/Correction procedures “Connection error. Please consult your Owner’s Man- This indicates a problem in the iPod or its con- ual for instructions on how nection. to connect the iPod.” This indicates that there is no music data in “No music files found.”...
Page 247 5-6. Using an external device WARNING ■ While driving Do not connect an iPod or operate the controls. NOTICE ■ To prevent damage to the iPod or its terminals ● Do not leave the iPod in the vehicle. The temperature inside the vehicle may become high, resulting in damage to the iPod.
Page 248 5-6. Using an external device Listening to a USB memory device Connecting a USB memory device enables you to enjoy music from the vehicle speakers. Touch “USB” on the audio source selection screen. Connecting a USB memory device P. 247 Audio control screen Pressing the “AUDIO”...
Page 249 5-6. Using an external device ■ USB memory functions ● Depending on the USB memory device that is connected to the system, the device itself may not be operable and certain functions may not be avail- able. If the device is inoperable or a function is unavailable due to a mal- function (as opposed to a system specification), disconnecting the device and reconnecting it may resolve the problem.
Page 250 5-6. Using an external device ● MP3 file compatibility • Compatible standards MP3 (MPEG1 AUDIO LAYERII, III, MPEG2 AUDIO LAYERII, III) • Compatible sampling frequencies MPEG1 AUDIO LAYERII, III: 32, 44.1, 48 (kHz) MPEG2 AUDIO LAYERII, III: 16, 22.05, 24 (kHz) •...
Page 251 5-6. Using an external device ● MP3, WMA and AAC playback • When a device containing MP3, WMA and AAC files is connected, all files in the USB memory device are checked. Once the file check is fin- ished, the first MP3, WMA and AAC file is played. To make the file check finish more quickly, we recommend that you do not include any files other than MP3, WMA and AAC files or create any unnecessary folders.
Page 252 5-6. Using an external device Using the AUX port To use the AUX port, connect a portable player, press the “AUDIO” button, then select “AUX” to display the audio control screen. Connecting a portable audio player P. 247 ■ Operating portable audio players connected to the multimedia system The volume can be adjusted using the vehicle's audio controls.
Page 253 ® 5-7.Connecting Bluetooth Preparations to use wireless communica- tion ® The following can be performed using Bluetooth wireless com- munication: A portable audio player can be operated and listened to via ■ multimedia system Hands-free phone calls can be made via a cellular phone ■...
Page 254 ® 5-7. Connecting Bluetooth WARNING  ■ Certifications for the Bluetooth FCC ID: BABFT0049B FCC ID: AJDK068 ● CAUTION: Radio Frequency Radiation Exposure This equipment complies with FCC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Expo- sure Guidelines in Supplement C to OET65.
Page 255 ® 5-7. Connecting Bluetooth Device registration/connection flow ® 1. Register the Bluetooth device to be used with multimedia system (P. 281, 282, 283) ® 2. Connect the Bluetooth device to be used (P. 285) To be used for audio To be used for hands-free phone ®...
Page 256 ® 5-7. Connecting Bluetooth Registering and connecting from the “Bluetooth* Setup” screen To display the screen shown below, press the “SETUP” button and select “Bluetooth ” on the “Setup” screen. Select to connect the device to be used with multimedia sys- tem.
Page 257 ® 5-7. Connecting Bluetooth ® Registering a Bluetooth audio player for the first time ® To use the Bluetooth Audio, it is necessary to register an audio player with the system. Once the player has been registered, it is possible to use the ®...
Page 258 ® 5-7. Connecting Bluetooth ® Registering a Bluetooth phone for the first time To use the hands-free system, it is necessary to register a ® Bluetooth phone with the system. Once the phone has been registered, it is possible to use the hands-free system.
Page 259 ® 5-7. Connecting Bluetooth ® Registering a Bluetooth device ® Bluetooth compatible phones (HFP) and portable audio players (AVP) can be registered simultaneously. You can register up to 5 ® Bluetooth devices. ® How to register a Bluetooth device Display the “Bluetooth* Setup” screen. (P. 280) Select “Add”.
Page 260 ® 5-7. Connecting Bluetooth Select “OK” when the connection status changes from “Connect- ing...” to “Connected”. If an error message is displayed, follow the guidance on the screen to try again. Registration can be performed from screens other than the “Bluetooth* Setup”...
Page 261 ® 5-7. Connecting Bluetooth ® Connecting a Bluetooth device ® Up to 5 Bluetooth devices (Phones [HFP] and audio players [AVP]) can be registered. ® If more than 1 Bluetooth device has been registered, select which device to connect to. Press the “SETUP”...
Page 262 ® 5-7. Connecting Bluetooth Manual connection When auto connection has failed or “Bluetooth* Power” is turned off, ® you must connect the Bluetooth device manually. ® Follow the steps in “Connecting a Bluetooth device” from “STEP 1”. (P. 285) : Bluetooth is a registered trademark of Bluetooth SIG, Inc. ®...
Page 263 ® 5-7. Connecting Bluetooth ® Displaying a Bluetooth device details You can confirm and change the registered device details. ® Bluetooth device registration status Display the “Bluetooth* Setup” screen. (P. 280) Select the device. Select “Device Info”. The following screen is dis- played: Device Name Change connection method...
Page 264 ® 5-7. Connecting Bluetooth ® Detailed Bluetooth system settings ® You can confirm and change the detailed Bluetooth settings. ® How to check and change detailed Bluetooth settings Display the “Bluetooth* Setup” screen. (P. 280) Select “System Settings”. The following screen is dis- played: ®...
Page 265 ® 5-8.Bluetooth Audio ® Listening to Bluetooth Audio ® The Bluetooth audio system enables the user to enjoy music played on a portable player from the vehicle speakers via wire- less communication. ® When a Bluetooth device cannot be connected, check the connec- tion status on the “Bluetooth* Audio”...
Page 266 ® 5-9.Bluetooth phone ® Using a Bluetooth Phone The hands-free system is a function that allows you to use your cellular phone without touching it. ® ® This system supports Bluetooth . Bluetooth is a wireless data system that allows the cellular phone to wirelessly connect to the hands-free system and make/receive calls.
Page 267 ® 5-9. Bluetooth phone Telephone switch (P. 302) ■ Microphone ■ The vehicle’s built in micro- phone is used when talking on the phone. The person you are speaking to can be heard from the front speakers. ® To use the hands-free system, you must register your Bluetooth phone in the system.
Page 268 ® 5-9. Bluetooth phone Making a call ® Once a Bluetooth phone is registered, you can make a call using the following procedure: Dialing Display the phone screen. (P. 290) Select the “Dial Pad” tab and enter a phone number. To delete the input phone number, select For the first digit, you can enter “+”...
Page 269 ® 5-9. Bluetooth phone Press the switch on the steering wheel. If the phonebook is empty, a message will be displayed. ® For a PBAP compatible Bluetooth phone and “Automatic Contact/  History Transfer” is off Select the desired item. Select to transfer new con- tacts from a cellular phone, select “Always”...
Page 270 ® 5-9. Bluetooth phone Calling using favorites list You can make a call using numbers registered in the contact. Display the phone screen. (P. 290) Select “Favorites” tab. Select the desired number to make a call. Dialing from call history You can make a call using the call history, which has the 3 functions below.
Page 271 ® 5-9. Bluetooth phone Receiving a call When a call is received, the following screen is displayed together with a sound. To answer the phone Press the switch on the steer- ing wheel or select To refuse a call Press the switch on the steering wheel or select To adjust the incoming call volume Turn the “PWR/VOL”...
Page 272 ® 5-9. Bluetooth phone Speaking on the phone The following screen is displayed when speaking on the phone. To adjust the call volume Select “-” or “+”. You can also adjust the volume using the steering switches or the volume knob. To prevent the other party from hearing your voice Select “Mute”.
Page 273 ® 5-9. Bluetooth phone ■ Release Tones ● A continuous tone signal is a character string that consists of numbers and the characters p or w. (e.g.056133w0123p#1) ● When the “p” pause tone is used, the tone data up until the next pause tone will be automatically sent after 2 seconds have elapsed.
Page 274 ® 5-9. Bluetooth phone Call waiting When a call is interrupted by a third party while talking, an incoming call message will be displayed. To talk with the other party: • Press the switch on the steering wheel. • Select To refuse the call: •...
Page 275 ® 5-9. Bluetooth phone ® Bluetooth phone message function Received messages can be forwarded from the connected ® Bluetooth phone, enabling checking and replying using the multimedia system. ® Depending on the type of Bluetooth phone connected, received messages may not be transferred to the message inbox. If the phone does not support the message function, this func- tion cannot be used.
Page 276 ® 5-9. Bluetooth phone Checking the messages Display the message inbox screen. (P. 299) Select the desired message from the list. Check that the message is dis- played. E-mails: Select “Mark Unread” or “Mark Read” to mark mail unread or read on the message inbox screen.
Page 277 ® 5-9. Bluetooth phone Replying to a message Display the message inbox screen. (P. 299) Select the desired message from the list. Select “Quick Message”. Select the desired message. Select “Send”. Editing quick reply message ■ Select “Quick Message”. Select corresponding to the desired message to edit.
Page 278 ® 5-9. Bluetooth phone Using the steering wheel switches The steering wheel switches can be used to operate a connected cellular phone. Operating a telephone using the steering wheel switches Steering wheel switches on the right hand side ■ Type A Type B ...
Page 279 ® 5-9. Bluetooth phone ® Bluetooth phone settings You can adjust the hands-free system to your desired settings. “Phone/Message Settings” screen To display the screen shown below, press the “SETUP” button, and select “Phone” on the “Setup” screen. Set the phone connection (P.
Page 280 ® 5-9. Bluetooth phone Contact/Call History Settings ® The contact can be transferred from a Bluetooth phone to the sys- tem. The contact also can be added, edited and deleted. The call history can be deleted and contact and favorites can be changed.
Page 281 ® 5-9. Bluetooth phone Update contacts from phone Operation methods differ between PBAP compatible and PBAP ® incompatible but OPP compatible Bluetooth phones. If your cellular phone is neither PBAP nor OPP compatible, the con- tacts cannot be transferred. ® For PBAP Compatible Bluetooth Phones ■...
Page 282 ® 5-9. Bluetooth phone Updating the contacts in a different way (From the “Call His- ■ tory” screen) ® For PBAP compatible Bluetooth phones, this function is available when “Automatic Contact/History Transfer” is set to off. (P. 304) Display the phone screen. (P. 290) Select the “Call History”...
Page 283 ® 5-9. Bluetooth phone Editing the contact data ® For PBAP compatible Bluetooth phones, this function is available when “Automatic Contact/History Transfer” is set to off. (P. 304) Select “Edit Contact”. Select the desired contact. Select corresponding to the desired name or number. For editing the name ...
Page 284 ® 5-9. Bluetooth phone Favorites list setting Up to 15 contacts (maximum of 4 numbers per contact) can be regis- tered in the favorites list. Registering the contacts in the favorites list ■ Select “Add Favorite”. Select the desired contact to add to the favorites list. Dimmed contacts are already stored as a favorite.
Page 285 ® 5-9. Bluetooth phone Deleting the contacts in the favorites list ■ Select “Remove Favorite”. Select the desired contacts and select “Remove”. Select “Yes” when the confirmation screen appears. Check that a confirmation screen is displayed when the opera- tion is complete. Deleting contacts in the favorites list in a different way (from the ...
Page 286 ® 5-9. Bluetooth phone Message Settings Display the “Phone/Message Settings” screen. (P. 303) Select “Messaging Settings”. Select the desired item to be set. automatic message transfer on/off. automatic message readout on/off. Set the SMS/MMS notifica- tion popup on/off. Set the e-mail notification popup on/off.
Page 287 ® 5-9. Bluetooth phone Displaying the “Messaging Settings” screen in a different way ■ Display the phone screen. (P. 290) Select Select “Settings”. Phone Display Settings Display the “Phone/Message Settings” screen. (P. 303) Select “Phone Display Settings”. Select the desired item to be set.
Page 288  For a list of specific devices which operation has been confirmed on this system, check with your Toyota dealer or the following web- site: http://www.toyota.com/entune.html The Bluetooth version of the connected cellular phone may be older than the specified version.
Page 289 ® 5-9. Bluetooth phone When registering/connecting a cellular phone  A cellular phone cannot be registered. An incorrect passcode was entered on the cellular phone.  Enter the correct passcode on the cellular phone. The registration operation has not been completed on the cellular phone side.
Page 290  For a list of specific devices which operation has been confirmed on this system, check with your Toyota dealer or the following web- site: http://www.toyota.com/entune.html Automatic phonebook transfer function on this system is set to off.
Page 291 ® 5-9. Bluetooth phone In other situations  Even though all conceivable measures have been taken, the symptom sta- tus does not change. The cellular phone is not close enough to this system.  Bring the cellular phone closer to this system. The cellular phone is the most likely cause of the symptom.
Page 292 ® 5-10.Bluetooth ® Bluetooth ® ■ When using the Bluetooth audio system ● In the following conditions, the system may not function. • If the portable audio player is turned off • If the portable audio player is not connected •...
Page 293 ® 5-10. Bluetooth ® ■ Bluetooth antenna The antenna is built into the display. If the portable audio player is behind the seat or in the glove box or console box, or is touching or covered by metal objects, the connection status may deteriorate.
Page 294 ® 5-10. Bluetooth ■ Compatible models ® The Bluetooth audio system supports portable audio players with the follow- ing specifications ® ● Bluetooth specifications: Ver. 2.0, or higher (Recommended: Ver. 3.0+EDR or higher) ● Profiles: • A2DP (Advanced Audio Distribution Profile) Ver. 1.0, or higher (Recommended: Ver.
Page 295 ® 5-10. Bluetooth ■ Certification NOTE: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interfer- ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Page 296 ® 5-10. Bluetooth WARNING ■ While driving Do not use the portable audio player, cellular phone or connect a device to ® the Bluetooth system. ■ Caution regarding interference with electronic devices ® ● Your audio unit is fitted with Bluetooth antennas.
Page 297 5-11.Using the voice command system Voice command system The voice command system enables the hands-free system to be operated using voice commands. Operations of the voice command system can be performed by selecting the menu corresponding to each function on the screen.
Page 298 5-11. Using the voice command system ■ Microphone P. 291 ■ When using the microphone ● It is unnecessary to speak directly into the microphone when giving a com- mand. ● When “Voice Prompt Interrupt” set to on, it is not necessary to wait for the confirmation beep before speaking a command.
Page 299 5-11. Using the voice command system Command list Some recognizable voice commands and their actions are shown below as examples. Basic  Command Action Prompts voice guidance to offer examples of com- “Help” mands or operation methods “Go Back” Returns to the previous screen Phone ...
Page 300 5-11. Using the voice command system CAMRY_U (OM33A86U)
Page 301 6-1. Using the air conditioning system and defogger  Manual air conditioning system Air conditioning controls Adjusting the temperature setting ■ To adjust the temperature setting, turn clockwise to increase the temperature and counterclockwise to decrease the tempera- ture. is not pressed, the system will blow ambient temperature air or heated air.
Page 302 6-1. Using the air conditioning system and defogger Other functions Switching between outside air and recirculated air modes ■ Press The mode switches between outside air mode (indicator off) and recir- culated air mode (indicator on) each time is pressed. Defogging the windshield ■...
Page 303 6-1. Using the air conditioning system and defogger Air outlets Location of air outlets ■ The air outlets and air volume change according selected airflow mode. Adjusting the position of and opening and closing the air out- ■ lets Direct air flow to the left or right, up or down.
Page 304 6-1. Using the air conditioning system and defogger ■ Outside/recirculated air mode ● When driving on dusty roads such as tunnels or in heavy traffic, set the out- side/recirculated air mode button to the recirculated air mode. This is effec- tive in preventing outside air from entering the vehicle interior.
Page 305 6-1. Using the air conditioning system and defogger WARNING ■ To prevent the windshield from fogging up ● Do not use during cool air operation in extremely humid weather. The difference between the temperature of the outside air and that of the windshield can cause the outer surface of the windshield to fog up, block- ing your vision.
Page 306 6-1. Using the air conditioning system and defogger  Automatic air conditioning system Air outlets and fan speed are automatically adjusted according to the temperature setting. Air conditioning controls Adjusting the temperature setting ■ To adjust the temperature setting, turn clockwise to increase the temperature and counterclockwise to decrease the tempera- ture.
Page 307 6-1. Using the air conditioning system and defogger Change the airflow mode ■ To change the airflow mode, press outlets used switched each time the button is pressed. Air flows to the upper body. Air flows to the upper body and feet.
Page 308 6-1. Using the air conditioning system and defogger Other functions Switching between outside air and recirculated air modes ■ Press The mode switches between outside air mode (indicator off) and recir- culated air mode (indicator on) each time is pressed. Defogging the windshield ■...
Page 309 6-1. Using the air conditioning system and defogger Air outlets Location of air outlets ■ The air outlets and air volume change according selected airflow mode. Adjusting the position of and opening and closing the air out- ■ lets Front Rear ...
Page 310 6-1. Using the air conditioning system and defogger ■ Using automatic mode Fan speed is adjusted automatically according to the temperature setting and the ambient conditions. Therefore, the fan may stop for a while until warm or cool air is ready to flow immediately after is pressed.
Page 311 6-1. Using the air conditioning system and defogger ■ Ventilation and air conditioning odors ● To let fresh air in, set the air conditioning system to the outside air mode. ● During use, various odors from inside and outside the vehicle may enter into and accumulate in the air conditioning system.
Page 312 6-1. Using the air conditioning system and defogger  Seat heaters WARNING ● Care should be taken to prevent injury if anyone in the following categories comes in contact with the seats when the heater is on: • Babies, small children, the elderly, the sick and the physically chal- lenged •...
Page 313 6-1. Using the air conditioning system and defogger ● Vehicles without a smart key system: The seat heaters can be used when the engine switch is in the “ON” posi- tion. Vehicles with a smart key system: The seat heaters can be used when the engine switch is in IGNITION ON mode.
Page 314 6-2. Using the interior lights Interior lights list Rear interior/personal lights (vehicles with moon roof) (P. 340) Interior light (vehicles without moon roof) (P. 340) Front interior/personal lights (vehicles with moon roof) or personal lights (vehicles without moon roof) (P. 340) Shift lever light (vehicles with moon roof) Engine switch light Door courtesy lights...
Page 315: Interior Lights
6-2. Using the interior lights Interior lights Vehicles without moon roof Vehicles with moon roof   Turns the lights on Turns the lights on/off linked to door positions. Turns the lights on/off linked to door positions. Turns the lights on/off Turns the lights off The rear interior lights will turn on/ off together with the front interior...
Page 316 6-2. Using the interior lights ● Illuminated entry system: Vehicles without a smart key system: The lights automatically turn on/off according to the engine switch position, whether the doors are locked/unlocked, and whether the doors are open/ closed. Vehicles with a smart key system: The lights automatically turn on/off according to the engine switch mode, the presence of the electronic key, whether the doors are locked/unlocked, and whether the doors are open/closed.
Page 317 6-3. Using the storage features List of storage features Auxiliary boxes (P. 346) Cup holders (P. 345) Glove box (P. 343) Open tray (P. 350) Bottle holders/door pockets Console box (P. 343) (P. 344) Coin holder (P. 344) WARNING ● Do not leave glasses, lighters or spray cans in the storage spaces, as this may cause the following when cabin temperature becomes high: •...
Page 318 6-3. Using the storage features Glove box Open (press the button) Lock with the master key (vehi- cles without a smart key sys- tem) mechanical (vehicles with a smart key sys- tem) Unlock with the master key (vehicles without a smart key system) or mechanical key (vehicles with a smart key sys- tem)
Page 319 6-3. Using the storage features ● The console box is provided with a cut out that allows cables to be routed from the power outlet in the console box with the lid closed. Coin holder Pull the lid down while pressing down the button.
Page 320: Cup Holders
6-3. Using the storage features NOTICE Put the cap on before stowing a bottle. Do not place open bottles in the bot- tle holders, or glass or paper cups containing liquid. The contents may spill and glass cups may break. Cup holders Front Rear...
Page 321: Auxiliary Boxes
6-3. Using the storage features Auxiliary boxes Type A Type B   Push the lid. Push the lid. Type C (if equipped)  ■ Cable pass through (type B) The auxiliary box is provided with a groove that allows cables to be routed from the power outlet in the auxiliary box with the lid closed.
Page 322 If the LED indicators flash even though the surface of the tray is not hot, the wireless charger may be malfunctioning. Consult your Toyota dealer. ■ When charging of the wireless charger stops temporarily If any of the following operations are performed with the electronic key present, charging may stop temporarily.
Page 323 Certification for the wireless charger For vehicles sold in the U.S.A.  This device complies with Part 18 of the FCC Rules. Toyota Motor Sales, U.S.A., Inc. 19001 S. Western Avenue Torrance, CA 90501 For vehicles sold in Canada ...
Page 324 When wireless keys (that emit radio waves) other than those of your vehi- cle are being used nearby. If in situations other than above the wireless charger does not operate prop- erly or the operation indicator light is blinking, the wireless charger may be malfunctioning. Contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 325 6-3. Using the storage features NOTICE ■ To prevent failure or damage to data (vehicles with a wireless charger) ● Do not bring magnetic cards, such as a credit card, or magnetic recording media, close to the wireless charger. Otherwise, data may be erased due to the influence of magnetism.
Page 326 6-3. Using the storage features Trunk features Grocery bag hooks NOTICE To prevent damage to the hooks, do not apply too much load to the hooks. CAMRY_U (OM33A86U)
Page 327 6-4. Other interior features Other interior features Sun visors To set the visor in the forward position, flip it down. To set the visor in the side posi- tion, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it backward.
Page 328 6-4. Other interior features Clock The clock on the Entune Audio can be adjusted by the following pro- cedure. For vehicles with a navigation system or Entune Audio Plus, refer to the “NAVIGATION AND MULTIMEDIA SYSTEM OWNER’S MAN- UAL”. Press the “SETUP” button and select “General” and then select “Clock”.
Page 329 6-4. Other interior features Ashtray (if equipped) An ashtray can be installed in the cup holder. (P. 345) WARNING ● When not in use, keep the ashtray closed. In the event of sudden braking, an accident may occur due to an occupant being struck by the open ash- tray or ash flying out.
Page 330 6-4. Other interior features Power outlets Please use as a power supply for electronic goods that use less than 12 VDC/10 A (power consumption of 120 W). When using electronic goods, make sure that the power consumption of all the connected power outlets is less than 120 W. Instrument cluster Console box ...
Page 331: Assist Grips
6-4. Other interior features Armrest Fold down the armrest for use. NOTICE To prevent damage to the armrest, do not apply too much load on the arm- rest. Assist grips An assist grip installed on the ceil- ing can be used to support your body while sitting on the seat.
Page 332 6-4. Other interior features Coat hooks Coat hooks are provided on the rear assist grips. WARNING Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.
Page 333 6-4. Other interior features  Garage door opener The garage door opener can be programmed to operate garage doors, gates, entry doors, door locks, home lighting systems, security systems, and other devices.  The garage door opener (HomeLink Universal Transceiver) is manu- ...
Page 334 6-4. Other interior features Press and hold one of the  HomeLink buttons and the transmitter button. When the  HomeLink indicator light changes from a slow to a rapid flash, you can release both buttons.  If the HomeLink indicator light comes on but does not flash, or flashes rapidly for 2 seconds...
Page 335 6-4. Other interior features Programming a Rolling Code system (for U.S. owners) ■ If your device is Rolling Code equipped, follow the steps under the heading  “Programming HomeLink ” before proceeding with the steps listed below. Locate the learn button on the ceiling mounted garage door opener motor.
Page 336 6-4. Other interior features Programming other devices ■ To program other devices such as home security systems, home door locks or lighting, contact your Toyota dealer for assistance. Reprogramming a button ■  The individual HomeLink buttons cannot be erased but can be reprogrammed.
Page 337 6-4. Other interior features ■ Before programming ● Install a new battery in the remote control transmitter. ● The battery side of the remote control transmitter must be pointed away  from the HomeLink button. ■ To prevent battery discharge Vehicles without a smart key system: ...
Page 338 6-4. Other interior features WARNING ■ When programming a garage door or other remote control devices The garage door or other devices may operate, so ensure people and objects are out of danger to prevent potential harm. ■ Conforming to federal safety standards ...
Page 339 Telematics Subscription Service Agreement and its Terms and Conditions, as in effect and amended from time to time, a current copy of which is available at Toyota.com. All use of the Safety Connect service is subject to such then-applicable Terms and Conditions.
Page 340 Safety Connect. ● Safety Connect is available beginning Fall 2009 on select Toyota models. Contact with the Safety Connect response center is dependent upon the telematics device being in operative condition, cellular connection availabil- ity, and GPS satellite signal reception, which can limit the ability to reach the response center or receive emergency service support.
Page 341 ● Green indicator light flashing = Safety Connect call in process ● Red indicator light (except at vehicle start-up) = System malfunction (contact your Toyota dealer) ● No indicator light (off) = Safety Connect service not active Safety Connect services Automatic Collision Notification ■...
Page 342 In addition to assisting law enforcement with recovery of a stolen vehicle, Safety-Connect-equipped vehicle location data may, under certain circumstances, be shared with third parties to locate your vehicle. Further information is available at Toyota.com. Emergency Assistance Button (“SOS”) ■...
Page 343 6-4. Other interior features Safety information for Safety Connect Important! Read this information before using Safety Connect. Exposure to radio frequency signals ■ The Safety Connect system installed in your vehicle is a low-power radio transmitter and receiver. It receives and also sends out radio frequency (RF) signals.
Page 344 6-4. Other interior features  Compass The compass on the inside rear view mirror indicates the direc- tion in which the vehicle is heading. Operation To turn the compass on or off, press and hold the switch for 3 seconds. Displays and directions Display Direction...
Page 345 6-4. Other interior features Calibrating the compass The direction display deviates from the true direction determined by the earth’s magnetic field. The amount of deviation varies according to the geographic position of the vehicle. If you cross over a map boundary shown in illustration, the compass will deviate.
Page 346 6-4. Other interior features Circling calibration ■ When “C” appears on the dis- play, drive the vehicle at 5 mph (8 km/h) or less in a circle until a direction is displayed. If there is not enough space to drive in a circle, drive around the block until a direction is dis- played.
Page 347 6-4. Other interior features NOTICE ■ To avoid compass malfunctions Do not place magnets or any metal objects near the inside rear view mirror. Doing this may cause the compass sensor to malfunction. ■ To ensure normal operation of the compass ●...
Page 348 7-1. Maintenance and care Cleaning and protecting the vehicle exterior Perform the following to protect the vehicle and maintain it in prime condition: ● Working from top to bottom, liberally apply water to the vehicle body, wheel wells and underside of the vehicle to remove any dirt and dust.
Page 349 Precaution regarding the rear bumper with Blind Spot Monitor (if equipped) If the paint of the rear bumper is chipped or scratched, the system may mal- function. If this occurs, avoid using the system and consult your Toyota dealer. CAMRY_U (OM33A86U)
Page 350 7-1. Maintenance and care NOTICE ■ To prevent paint deterioration and corrosion on the body and compo- nents (aluminum wheels etc.) ● Wash the vehicle immediately in the following cases: • After driving near the sea coast • After driving on salted roads •...
Page 351 7-1. Maintenance and care Cleaning and protecting the vehicle interior The following procedures will help protect your vehicle’s interior and keep it in top condition: Protecting the vehicle interior Remove dirt and dust using a vacuum cleaner. Wipe dirty surfaces with a cloth dampened with lukewarm water.
Page 352 7-1. Maintenance and care ■ Caring for leather areas Toyota recommends cleaning the interior of the vehicle at least twice a year to maintain the quality of the vehicle's interior. ■ Shampooing the carpets There are several commercial foaming-type cleaners available. Use a sponge or brush to apply the foam.
Page 353 7-1. Maintenance and care NOTICE ■ Cleaning detergents ● Do not use the following types of detergent, as they may discolor the vehi- cle interior or cause streaks or damage to painted surfaces: • Non-seat portions: Organic substances such as benzene or gasoline, alkaline or acidic solutions, dye, and bleach •...
Page 354 Toyota recommends the following main- tenance: General maintenance General maintenance should be performed on a daily basis. This can be done by yourself or by a Toyota dealer. Scheduled maintenance Scheduled maintenance should be performed at specified intervals according to the maintenance schedule.
Page 355 ■ Repair and replacement It is recommended that genuine Toyota parts be used for repairs to ensure performance of each system. If non-Toyota parts are used in replacement or if a repair shop other than a Toyota dealer performs repairs, confirm the war- ranty coverage.
Page 356 7-2. Maintenance WARNING ■ If your vehicle is not properly maintained Improper maintenance could result in serious damage to the vehicle and possible death or serious injury. ■ Handling of the battery ● Engine exhaust, some of its constituents, and a wide variety of automobile components contain or emit chemicals known to the State of California to cause cancer and birth defects and other reproductive harm.
Page 357 “Owner’s Warranty Information Booklet” or “Owner’s Manual Supplement/Sched- uled Maintenance Guide”. It is recommended that any problem you notice should be brought to the attention of your Toyota dealer or qualified service shop for advice. Engine compartment...
Page 358 7-2. Maintenance Vehicle interior Items Check points • The accelerator pedal should Accelerator pedal move smoothly (without uneven pedal effort or catching). • When parked on a slope and the Automatic transmission “Park” shift lever is in P, is the vehicle mechanism securely stopped? •...
Page 359 7-2. Maintenance Items Check points • Do seat belts operate smoothly? Seat belts • The seat belts should not be dam- aged. • Do the seat controls operate prop- Seats erly? • Does the steering wheel rotate smoothly? • Does the steering wheel have the Steering wheel correct amount of free play? •...
Page 360 7-2. Maintenance WARNING ■ If the engine is running Turn the engine off and ensure that there is adequate ventilation before per- forming maintenance checks. CAMRY_U (OM33A86U)
Page 361 The OBD system determines that a problem exists somewhere in the emission control system. Your vehicle may not pass the I/M test and may need to be repaired. Contact your Toyota dealer to service the vehicle. Your vehicle may not pass the I/M test in the following situations: ●...
Page 362 • Rag or paper towel (P. 399) • Funnel (used only for adding brake fluid) • “Toyota Super Long Life Coolant” or a similar high quality ethylene glycol-based non-silicate, non- amine, non-nitrite and non-borate coolant with long- life hybrid organic acid technology U.S.A.:...
Page 363 7-3. Do-it-yourself maintenance WARNING The engine compartment contains many mechanisms and fluids that may move suddenly, become hot, or become electrically energized. To avoid death or serious injury, observe the following precautions. ■ When working on the engine compartment ● Keep hands, clothing and tools away from the moving fan and engine drive belt.
Page 364 7-3. Do-it-yourself maintenance Hood Release the lock from the inside of the vehicle to open the hood. Pull the hood lock release lever. The hood will pop up slightly. Pull up the auxiliary catch lever and lift the hood. WARNING ■...
Page 365 7-3. Do-it-yourself maintenance Positioning a floor jack When using a floor jack, follow the instructions in the manual provided with the jack and perform the operation safely. When raising your vehicle with a floor jack, position the jack cor- rectly. Improper placement may damage your vehicle or cause injury.
Page 366 7-3. Do-it-yourself maintenance Engine compartment 2.5 L 4-cylinder (2AR-FE) engine  Fuse boxes (if equipped) Battery (P. 400) (P. 424) Radiator (P. 398) Engine oil filler cap (P. 395) Electric cooling fans Engine oil level dipstick Condenser (P. 398) (P. 394) Engine coolant reservoir Brake fluid reservoir (P.
Page 367 7-3. Do-it-yourself maintenance 3.5 L V6 (2GR-FE) engine  Fuse boxes (P. 424) Radiator (P. 398) Engine oil filler cap (P. 395) Electric cooling fans Engine oil level dipstick Condenser (P. 398) (P. 394) Engine coolant reservoir Brake fluid reservoir (P.
Page 368 7-3. Do-it-yourself maintenance Engine oil With the engine at operating temperature and turned off, check the oil level on the dipstick. Checking the engine oil ■ Park the vehicle on level ground. After warming up the engine and turning it off, wait more than 5 minutes for the oil to drain back into the bottom of the engine.
Page 369 7-3. Do-it-yourself maintenance Wipe the dipstick and reinsert it fully. Adding engine oil ■ If the oil level is below or near the low level mark, add engine oil of the same type as that already in the engine. Make sure to check the oil type and prepare the items needed before adding oil.
Page 370 Dispose of used oil and filters only in a safe and acceptable manner. Do not dispose of used oil and filters in household trash, in sewers or onto the ground. Call your Toyota dealer, service station or auto parts store for information concerning recycling or disposal. ●...
Page 371: Engine Coolant
If the coolant level drops within a short time of replenishing Visually check the radiator, hoses, engine coolant reservoir caps, drain cock and water pump. If you cannot find a leak, have your Toyota dealer test the cap and check for leaks in the cooling system. CAMRY_U (OM33A86U)
Page 372 Radiator and condenser Check the radiator and condenser and clear away any foreign objects. If either of the above parts is extremely dirty or you are not sure of their condition, have your vehicle inspected by your Toyota dealer. WARNING ■...
Page 373 7-3. Do-it-yourself maintenance Brake fluid Checking fluid level ■ The brake fluid level should be between the “MAX” and “MIN” lines on the tank. “MAX” “MIN” Adding fluid ■ Make sure to check the fluid type and prepare the necessary item. Fluid type FMVSS No.116 DOT 3 or SAE J1703 brake fluid Item...
Page 374 Make sure to turn off the engine before disconnecting the battery. Take extra care when connecting the bat- tery if the engine switch mode prior to discharge is unknown. If the system will not start even after multiple attempts, contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 375 7-3. Do-it-yourself maintenance WARNING ■ Chemicals in the battery Batteries contain poisonous and corrosive sulfuric acid and may produce hydrogen gas which is flammable and explosive. To reduce the risk of death or serious injury, take the following precautions while working on or near the battery: ●...
Page 376 7-3. Do-it-yourself maintenance Washer fluid Add washer fluid in the following situations: ● A washer does not work. ● Vehicles without a multi-infor- mation display: The low wind- shield washer fluid warning light comes on. (P. 448) ● Vehicles with a multi-informa- tion display: The warning mes- sage appears on the multi- information display.
Page 377 Tire rotation Rotate the tires in the order shown. To equalize tire wear and extend tire life, Toyota recommends that tire rotation is carried out at the Front same interval as tire inspection. Do not fail to initialize the tire pressure warning system after tire rotation.
Page 378 ID codes must be registered in the tire pressure warning computer and the tire pressure warning system must be initialized. Have tire pressure warning valves and transmitter ID codes registered by your Toyota dealer. (P. 405) ◆ Initializing the tire pressure warning system The tire pressure warning system must be initialized in the fol- ■...
Page 379 The tire pressure warning valve and transmitter is equipped with a unique ID code. When replacing a tire pressure warning valve and transmitter, it is necessary to register the ID code. Have the ID code registered by your Toyota dealer. CAMRY_U (OM33A86U)
Page 380 A tire goes flat repeatedly or cannot be properly repaired due to the size or location of a cut or other damage If you are not sure, consult with your Toyota dealer. ■ Replacing tires and wheels (vehicles with a tire pressure warning...
Page 381 7-3. Do-it-yourself maintenance ■ Tire types ● Summer tires Summer tires are high-speed performance tires best suited to highway driving under dry conditions. Since summer tires do not have the same traction performance as snow tires, summer tires are inadequate for driving on snow-covered or icy roads.
Page 382 ● In the following cases, the tire pressure warning system may not operate properly. • If non-genuine Toyota wheels are used. • A tire has been replaced with a tire that is not an OE (Original Equip- ment) tire. • A tire has been replaced with a tire that is not of the specified size.
Page 383 7-3. Do-it-yourself maintenance ■ The initialization operation (vehicles with a tire pressure warning system) ● Make sure to carry out initialization after adjusting the tire inflation pres- sure. Also, make sure the tires are cold before carrying out initialization or tire inflation pressure adjustment.
Page 384 After performing initialization, the tire pressure warning light blinks for 1 minute then stays on while driving. If the inflation pressure of each tire is still not displayed, have the vehicle inspected by your Toyota dealer. ■ Tire pressure warning system certification...
Page 385 Do not mix tires of different makes, models or tread patterns. Also, do not mix tires of remarkably different treadwear. ● Do not use tire sizes other than those recommended by Toyota. ● Do not mix differently constructed tires (radial, bias-belted or bias-ply tires).
Page 386 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 387 7-3. Do-it-yourself maintenance Tire inflation pressure Tire inflation pressure The recommended cold tire infla- tion pressure and tire size are dis- played on the tire and loading information label. (P. 506) CAMRY_U (OM33A86U)
Page 388 Driving with incorrect tire inflation pressure may result in the following: ● Reduced fuel efficiency ● Reduced driving comfort and tire life ● Reduced safety ● Damage to the drivetrain If a tire needs frequent inflating, have it checked by your Toyota dealer. CAMRY_U (OM33A86U)
Page 389 7-3. Do-it-yourself maintenance ■ Instructions for checking tire inflation pressure When checking tire inflation pressure, observe the following: ● Check only when the tires are cold. If your vehicle has been parked for at least 3 hours or has not been driven for more than 1 mile or 1.5 km, you will get an accurate cold tire inflation pressure reading.
Page 390 ● Used wheels ● Bent wheels that have been straightened Aluminum wheel precautions (if equipped) ● Use only Toyota wheel nuts and wrenches designed for use with your aluminum wheels. ● When rotating, repairing or changing your tires, check that the wheel nuts are still tight after driving 1000 miles (1600 km).
Page 391 Because tire repair or replacement may affect the tire pressure warn- ing valves and transmitters, make sure to have tires serviced by your Toyota dealer or other qualified service shop. In addition, make sure to purchase your tire pressure warning valves and transmitters at your Toyota dealer.
Page 392 7-3. Do-it-yourself maintenance Air conditioning filter The air conditioning filter must be changed regularly to maintain air conditioning efficiency. Removal method Turn the engine switch off. Open glove remove the glove box cover inside the glove box. Remove the filter cover. Remove the air conditioning fil- ter and replace it with a new one.
Page 393 7-3. Do-it-yourself maintenance ■ Checking interval Inspect and replace the air conditioning filter according to the maintenance schedule. In dusty areas or areas with heavy traffic flow, early replacement may be required. (For scheduled maintenance information, please refer to the “Schedule maintenance guide”...
Page 394 7-3. Do-it-yourself maintenance Wireless remote control/electronic key battery Replace the battery with a new one if it is depleted. You will need the following items: ● Flathead screwdriver ● Small flathead screwdriver ● Lithium battery CR2016 (vehicles without a smart key system), or CR2032 (vehicles with a smart key system) Replacing the battery Vehicles without a smart key system (type A)
Page 395 7-3. Do-it-yourself maintenance Vehicles without a smart key system (type B)  Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag. To prevent the buttons from being disassembled, face the button sur- face downward.
Page 396 7-3. Do-it-yourself maintenance Vehicles with a smart key system  Take out the mechanical key. Remove the cover. To prevent damage to the key, cover the tip of the screwdriver with a rag. Remove the depleted battery using a small flathead screw- driver.
Page 397 Use a CR2016 (vehicles without a smart key system) or CR2032 (vehicles with a smart key system) lithium battery ● Batteries can be purchased at your Toyota dealer, local electrical appliance shops or camera stores. ● Replace the battery only with the same or equivalent type recommended by the manufacturer.
Page 398 7-3. Do-it-yourself maintenance Checking and replacing fuses If any of the electrical components do not operate, a fuse may have blown. If this happens, check and replace the fuses as nec- essary. Turn the engine switch off. Open the fuse box cover. Engine compartment (type A) Engine compartment (type B) ...
Page 399 Normal fuse Blown fuse Type A and B: Replace the blown fuse with a new fuse of an appropriate amperage rat- ing. The amperage rating can be found on the fuse box lid. Type C: Contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 400 If the lights do not turn on even after the fuse has been replaced, a bulb may need replacement. (P. 427) ● If the replaced fuse blows again, have the vehicle inspected by your Toyota dealer. ■ If there is an overload in a circuit The fuses are designed to blow, protecting the wiring harness from damage.
Page 401 Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer.
Page 402 7-3. Do-it-yourself maintenance Replacing light bulbs Headlight high beams (halogen bulb)/daytime running light ■ (halogen bulb) Turn the bulb base counter- clockwise. Pull the bulb out while press- ing the lock release of the connector. When installing, reverse the steps listed. CAMRY_U (OM33A86U)
Page 403 7-3. Do-it-yourself maintenance Headlight low beams (halogen bulb) ■ Turn the bulb base counter- clockwise. Pull the bulb out while press- ing the lock release of the connector. When installing, reverse the steps listed. Front side marker lights ■ Turn the bulb base counter- clockwise.
Page 404 7-3. Do-it-yourself maintenance Front turn signal/parking lights (bulb type) ■ To ensure enough space to perform work, turn the steer- ing wheel to rotate the front wheel away from the bulb to be replaced. Turn the steering wheel to the left when replacing the right side light bulb, and turn the steering wheel to the right when replac-...
Page 405 7-3. Do-it-yourself maintenance Remove the light bulb. When installing, reverse the steps listed. Stop/tail/rear side marker lights and rear turn signal lights ■ Open trunk remove the luggage trim cover clips. (P. 435) Pull the hook while depress- ing the button. Partly remove the luggage trim cover.
Page 406 7-3. Do-it-yourself maintenance Turn the bulb base counter- clockwise. Rear turn signal light Stop/tail/rear side marker light Remove the light bulb. Rear turn signal light Stop/tail/rear side marker light When installing, reverse the steps listed. CAMRY_U (OM33A86U)
Page 407 7-3. Do-it-yourself maintenance Back-up lights ■ Open trunk remove the clips. (P. 435) Then partly remove the trunk panel cover. Unplug the connector while depressing the lock release. Turn the bulb base counter- clockwise. Remove the light bulb. When installing, reverse the steps listed. CAMRY_U (OM33A86U)
Page 408 When installing, reverse the steps listed. Replacing the following bulbs ■ If any of the lights listed below has burnt out, have it replaced by your Toyota dealer. ● Headlight low/high beams (LED type) ● Parking lights/daytime running lights (LED type) ● High mounted stoplights...
Page 409 The headlight low/high beams (LED type), parking lights/daytime running lights (LED type) and high mounted stoplights consist of a number of LEDs. If any of the LEDs burns out, take your vehicle to your Toyota dealer to have the light replaced.
Page 410 7-3. Do-it-yourself maintenance CAMRY_U (OM33A86U)
Page 411 8-1. Essential information Emergency flashers The emergency flashers are used to warn other drivers when the vehicle has to be stopped in the road due to a breakdown, etc. Press the switch. All the turn signal lights will flash. To turn them off, press the switch once again.
Page 412 8-1. Essential information If your vehicle has to be stopped in an emergency Only in an emergency, such as if it becomes impossible to stop the vehicle in the normal way, stop the vehicle using the follow- ing procedure: Steadily step on the brake pedal with both feet and firmly depress it. Do not pump the brake pedal repeatedly as this will increase the effort required to slow the vehicle.
Page 413 8-1. Essential information WARNING ■ If the engine has to be turned off while driving ● Power assist for the brakes and steering wheel will be lost, making the brake pedal harder to depress and the steering wheel heavier to turn. Decelerate as much as possible before turning off the engine.
Page 414 If your vehicle needs to be towed If towing is necessary, we recommend having your vehicle towed by your Toyota dealer or commercial towing service, using a lift-type truck or flat bed truck. Use a safety chain system for all towing, and abide by all state/ provincial and local laws.
Page 415 Release the parking brake. Use a towing dolly under the front wheels. Using a flat bed truck If your Toyota is transported by a flatbed truck, it should be tied down at the locations shown in the illustration. If you use chains or cables to tie down your vehicle, the angles shaded in black must be 45.
Page 416 8-2. Steps to take in an emergency WARNING Observe the following precautions. Failure to do so may result in death or serious injury. ■ When towing the vehicle Be sure to transport the vehicle with the front wheels raised or with all four wheels raised off the ground.
Page 417 8-2. Steps to take in an emergency If you think something is wrong If you notice any of the following symptoms, your vehicle proba- bly needs adjustment or repair. Contact your Toyota dealer as soon as possible. Visible symptoms ● Fluid leaks under the vehicle.
Page 418 8-2. Steps to take in an emergency Fuel pump shut off system To minimize the risk of fuel leakage when the engine stalls or when an airbag inflates upon collision, the fuel pump shut off system stops the supply of fuel to the engine. Follow the procedure below to restart the engine after the system is activated.
Page 419  Immediately stop the vehicle in a safe place and con- (Canada) tact your Toyota dealer. Continuing to drive the vehi- cle may be dangerous. Charging system warning light Indicates a malfunction in the vehicle’s charging system ...
Page 420 Indicates a malfunction in: • The SRS airbag system; • The front passenger occupant classification system; or • The seat belt pretensioner system  Have the vehicle inspected by your Toyota dealer immediately. ABS warning light Indicates a malfunction in: •...
Page 421 Toyota dealer. When the light comes on after blinking for 1 minute: Malfunction in the tire pressure warning system  Have the system checked by your Toyota dealer. CAMRY_U (OM33A86U)
Page 422 8-2. Steps to take in an emergency Warning light Warning light/Details/Actions Maintenance required reminder light Indicates that maintenance is required according to the driven distance on the maintenance schedule. Illuminates for about 3 seconds and then flashes for about 15 seconds approximately 4500 miles (7200 km) after the reminder light (vehicles without a multi-information dis- play) or massage (vehicles with a multi-information dis- play) has been reset.
Page 423 8-2. Steps to take in an emergency : Driver’s seat belt buzzer: Vehicles without a smart key system: The driver’s seat belt buzzer sounds to alert the driver that his or her seat belt is not fastened. Once the engine switch is turned to the “ON”...
Page 424 Is the fuel tank cap loose? If it is, tighten it securely. The light will go off after several driving trips. If the light does not go off even after several trips, contact your Toyota dealer as soon as possible. ■...
Page 425 1 minute (vehicles with a tire pressure warning system) If the tire pressure warning light frequently comes on after blinking for 1 minute when the engine switch is turned on, have it checked by your Toyota dealer. ■ Warning buzzer In some cases, the buzzer may not be heard because of noisy place or an audio sound.
Page 426 ■ If both the ABS and the brake system warning lights remain on Stop your vehicle in a safe place immediately and contact your Toyota dealer. The vehicle will become extremely unstable during braking, and the ABS system may fail, which could cause an accident resulting in death or serious injury.
Page 427 8-2. Steps to take in an emergency WARNING ■ Maintenance of the tires Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label (tire and load information label).
Page 428 8-2. Steps to take in an emergency NOTICE ■ To ensure the tire pressure warning system operates properly (vehicles with a tire pressure warning system) Do not install tires with different specifications or makers, as the tire pressure warning system may not operate properly. CAMRY_U (OM33A86U)
Page 429 Multi-information display If any of the warning message or indicator comes on again after the following actions have been performed, contact your Toyota dealer. Warning message and warning buzzer list Warning message Details/Actions Indicates that: •...
Page 430 Indicates a malfunction in the EPS (Electric Power Steering) system A buzzer also sounds.  Have the vehicle inspected by your Toyota dealer. Indicates that the vehicle is being driven at 3 mph (5 km/h) or more with the parking brake still engaged A buzzer also sounds.
Page 431 Indicates a malfunction in: • The ABS; or • The brake assist system (U.S.A.) A buzzer also sounds.  Have the vehicle inspected by your Toyota dealer. (Canada) Indicates a malfunction in the VSC (Vehicle Sta- bility Control) system.  Have the vehicle inspected by your Toyota dealer.
Page 432 Press the “ON-OFF” button once to deactivate the system, and then press the button again to reactivate the system. A buzzer also sounds.  Have the vehicle inspected by your Toyota dealer. Indicates a malfunction in the LDA (Lane Depar- ture Alert) system A buzzer also sounds.
Page 433 8-2. Steps to take in an emergency Warning message Details/Actions Indicates a malfunction in the PCS (Pre-Collision system) A buzzer also sounds.  Have the vehicle inspected by your Toyota dealer. (Flashes) (If equipped) Indicates a malfunction in the BSM (Blind Spot Monitor) system A buzzer also sounds.
Page 434 (If equipped) Indicates a malfunction in the Automatic High Beam system A buzzer also sounds.  Have the vehicle inspected by your Toyota dealer. (If equipped) Indicates that the tire inflation pressure is low  Check the tire inflation pressure, and adjust to the appropriate level.
Page 435 (Vehicles with a tire inflation pres- sure display function) there is a malfunction in the system. Have the vehicle inspected at your Toyota dealer. (If equipped) Indicates that the tire position information can- not be recognized  Drive for a short while and check if the display updates.
Page 436 8-2. Steps to take in an emergency Warning message Details/Actions Indicates that remaining fuel is approximately 2.6 gal. (9.7 L, 2.1 Imp. gal.) or less  Refuel the vehicle. Indicates that the TRAC (Traction Control) sys- tem has been deactivated ...
Page 437 8-2. Steps to take in an emergency Warning message Details/Actions Indicates that, since the VSC (Vehicle Stability Control) system was turned off, the pre-collision brake system operation is stopped  Turn the VSC on. (P. 218) (If equipped) Indicates that the PCS (Pre-collision system) is not currently functional because the grille cover or the sensor is dirty ...
Page 438 8-2. Steps to take in an emergency ■ Warning message in dynamic radar cruise control mode (if equipped) In the following situations, the warning message may not be displayed even if vehicle-to-vehicle distance decreases: ● When your vehicle and the vehicle ahead are traveling at the same speed or the vehicle ahead is traveling more quickly than your vehicle ●...
Page 439 8-2. Steps to take in an emergency Have the malfunction repaired immediately. (vehicles with a smart key system) After taking the specified steps to correct the suspected problem, check that the warning message and light go off. Interior Exterior Warning message Details/Actions buzzer buzzer...
Page 440 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer The driver’s door was opened and closed while the electronic key was not in the vehicle, the shift lever was in P and the engine switch was not turned off.
Page 441 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer An attempt was made to drive when the electronic key was not inside the vehicle.   Confirm times that elec- tronic key is inside the vehicle.
Page 442 (Flashes) right. Indicates a malfunction in the smart key system  Once  Have the vehicle inspected by your Toyota dealer. (Flashes) • When doors were unlocked with the mechanical key and then the engine switch was pressed, the elec-...
Page 443 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer An attempt was made to start the engine with the shift lever in  Once an incorrect position.  Shift the shift lever to P and start the engine. (Flashes) The engine switch has been turned off with the shift lever in...
Page 444 8-2. Steps to take in an emergency Interior Exterior Warning message Details/Actions buzzer buzzer During a engine starting proce- dure in the event that the elec- tronic key was not functioning properly (P. 488), the engine  Once switch was touched with the electronic key.
Page 445 8-2. Steps to take in an emergency If you have a flat tire Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire. For details about tires: P. 403 WARNING ■ If you have a flat tire Do not continue driving with a flat tire.
Page 446 8-2. Steps to take in an emergency Location of the spare tire, jack and tools Luggage floor cover Jack handle Wheel nut wrench Jack Spare tire CAMRY_U (OM33A86U)
Page 447 8-2. Steps to take in an emergency WARNING ■ Using the tire jack Observe the following precautions. Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury. ● Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.
Page 448 8-2. Steps to take in an emergency Secure the luggage floor cover using the hook provided. Remove the jack. Taking out the spare tire Lift up the hook of the luggage floor cover on the trunk floor. Secure the luggage floor cover using the hook provided.
Page 449 8-2. Steps to take in an emergency Remove the tool tray. Loosen the center fastener that secures the spare tire. When taking out or stowing the spare tire, make sure to firmly hold opposite ends of the tire. WARNING ■ When storing the spare tire Be careful not to catch fingers or other body parts between the spare tire and the body of the vehicle.
Page 450 8-2. Steps to take in an emergency Replacing a flat tire Chock the tires. Flat tire Wheel chock positions Left-hand side Behind the rear right-hand side tire Front Right-hand side Behind the rear left-hand side tire Left-hand side In front of the front right-hand side tire Rear Right-hand side In front of the front left-hand side tire...
Page 451 8-2. Steps to take in an emergency Turn the tire jack portion “A” by hand until the notch of the jack is in contact with the jack point. The jack point guides are located under the rocker panel. They indicate the jack point positions. Raise the vehicle until the tire is slightly raised off the ground.
Page 452 • If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer. • When installing the wheel nuts, be sure to install them with the tapered ends facing inward.
Page 453 8-2. Steps to take in an emergency Installing the spare tire Remove any dirt or foreign mat- ter from the wheel contact sur- face. If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off.
Page 454 8-2. Steps to take in an emergency Firmly tighten each wheel nut two or three times in the order shown in the illustration. Tightening torque: 76 ft•lbf (103 N•m, 10.5 kgf•m) Stow the flat tire, tire jack and all tools. ■...
Page 455 8-2. Steps to take in an emergency WARNING ■ When using the compact spare tire ● Remember that the compact spare tire provided is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle. ●...
Page 456 When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire.
Page 457 8-2. Steps to take in an emergency If the engine will not start If the engine will not start even though correct starting proce- dures are being followed (P. 155, 157), consider each of the fol- lowing points: The engine will not start even though the starter motor operates normally.
Page 458 ● There may be a malfunction in the steering lock system (vehicles with a smart key system). Contact your Toyota dealer if the problem cannot be repaired, or if repair procedures are unknown. Emergency start function (vehicles with a smart key system)
Page 459 (a sys- tem to prevent accidental operation of the shift lever). Have the vehicle inspected by your Toyota dealer immediately. The following steps may be used as an emergency measure to ensure that the shift lever can be shifted: Set the parking brake.
Page 460 Unlocks the door Turning the key rearward unlocks the driver's door. Turning the key once again unlocks the other doors. Opens the windows and moon roof (turn and hold) : This setting must be customized at your Toyota dealer. CAMRY_U (OM33A86U)
Page 461 Firmly depress the brake pedal and check that is displayed on the multi-information display. Press the engine switch. In the event that the engine still cannot be started, contact your Toyota dealer. ■ Stopping the engine Shift the shift lever to P and press the engine switch as you normally do when stopping the engine.
Page 462 The following procedures may be used to start the engine if the vehicle’s battery is discharged. You can also call your Toyota dealer or a qualified repair shop. If you have a set of jumper (or booster) cables and a second vehicle with a 12-volt battery, you can jump start your vehicle by following the steps below.
Page 463 IGNITION ON mode, then start the vehicle's engine. Once the vehicle’s engine has started, remove the jumper cables in the exact reverse order from which they were connected. Once the engine starts, have the vehicle inspected at your Toyota dealer as soon as possible. CAMRY_U (OM33A86U)
Page 464 8-2. Steps to take in an emergency ■ Starting the engine when the battery is discharged The engine cannot be started by push-starting. ■ To prevent battery discharge ● Turn off the headlights and the audio system while the engine is off. ●...
Page 465 8-2. Steps to take in an emergency WARNING ■ Avoiding battery fires or explosions Observe the following precautions to prevent accidentally igniting the flam- mable gas that may be emitted from the battery: ● Make sure each jumper cable is connected to the correct terminal and that it is not unintentionally in contact with any other than the intended terminal.
Page 466 If you do not see steam: Carefully lift the hood. After the engine has cooled down sufficiently, inspect the hoses and radiator core (radia- tor) for any leaks. Radiator Cooling fans If a large amount of coolant leaks, immediately contact your Toyota dealer. CAMRY_U (OM33A86U)
Page 467 (The fans may not operate in freezing temperatures.) If the fans are not operating: Stop the engine immediately and contact your Toyota dealer. If the fans are operating: Have the vehicle inspected at the nearest Toyota dealer.
Page 468 8-2. Steps to take in an emergency WARNING ■ When inspecting under the hood of your vehicle Observe the following precautions. Failure to do so may result in serious injury such as burns. ● If steam is seen coming from under the hood, do not open the hood until the steam has subsided.
Page 469 8-2. Steps to take in an emergency If the vehicle becomes stuck Carry out the following procedures if the tires spin or the vehicle becomes stuck in mud, dirt or snow: Stop the engine. Set the parking brake and shift the shift lever to P. Remove the mud, snow or sand from around the front wheels.
Page 470 8-2. Steps to take in an emergency ■ When it is difficult to free the vehicle Press to turn off TRAC. : Vehicles without multi-information dis- play : Vehicles with multi-information display WARNING ■ When attempting to free a stuck vehicle If you choose to push the vehicle back and forth to free it, make sure the surrounding area is clear to avoid striking other vehicles, objects or people.
Page 471 8-2. Steps to take in an emergency CAMRY_U (OM33A86U)
Page 472 9-1.Specifications Maintenance data (fuel, oil level, etc.) Dimensions and weights Overall length 190.9 in. (4850 mm) Overall width 71.7 in. (1820 mm) Overall height 57.9 in. (1470 mm) Wheelbase 109.3 in. (2775 mm) 62.4 in. (1585 mm) Front 62.8 in. (1595 mm) Tread 62.0 in.
Page 473 The vehicle identification number (VIN) is the legal identifier for your vehicle. This is the primary identification number for your Toyota. It is used in registering the ownership of your vehicle. This number is stamped on the top left of the instrument panel.
Page 474 Drive belt type (2.5 L 4-cylinder [2AR-FE] engine only) The high strength drive belt is used for the generator side drive belt. When replacing the drive belt, use Toyota genuine drive belt or equivalent high strength drive belt. If the high strength drive belt is not used, durability of the belt may become less than expected.
Page 475: Lubrication System
Engine oil selection ■ “Toyota Genuine Motor Oil” is used in your Toyota vehicle. Use Toyota approved “Toyota Genuine Motor Oil” or equivalent to sat- isfy the following grade and viscosity. Oil grade: ILSAC GF-5 multigrade engine oil...
Page 476 3.5 L V6 (2GR-FE) engine  9.6 qt. (9.1 L, 8.0 Imp. qt.) Use either of the following: • “Toyota Super Long Life Coolant” • A similar high-quality ethylene glycol-based Coolant type non-silicate, non-amine, non-nitrite, and non-borate coolant with long-life hybrid organic acid technology Do not use plain water alone.
Page 477: Ignition System
Toyota dealer. NOTICE ■ Transmission fluid type Using transmission fluid other than “Toyota Genuine ATF WS” may cause deterioration in shift quality, locking up of the transmission accompanied by vibration and, ultimately, damage to the vehicle’s transmission. CAMRY_U (OM33A86U)
Page 478 9-1. Specifications Brakes Pedal clearance 3.8 in. (96 mm) 0.04  0.24 in. (1  6 mm) Pedal free play Brake pad wear limit 0.04 in. (1.0 mm) Parking brake lining wear limit 0.04 in. (1.0 mm)  10 clicks Parking brake pedal travel Fluid type SAE J1703 or FMVSS No.116 DOT 3...
Page 479 9-1. Specifications Type B  Tire size P215/55R17 93V, T155/70D17 110M Driving under normal conditions Front: 35 psi (240 kPa, 2.4 kgf/cm bar) Rear: 35 psi (240 kPa, 2.4 kgf/cm bar) Spare: Tire inflation pressure 60 psi (420 kPa, 4.2 kgf/cm or bar) (Recommended cold tire Driving at high speeds (above 100 mph [160...
Page 480 9-1. Specifications Light bulbs Light bulbs Bulb No. Type Headlights Low beam  (halogen bulbs) High beam 9005 (halogen bulbs) Front side marker lights Front turn signal/ Exterior parking lights 7444NA 28/8 (bulb type) Rear turn signal lights WY21W Stop/tail/rear side 7443 21/5 maker lights...
Page 481 In very few cases, driveability problems may be caused by the brand of gaso- line you are using. If driveability problems persist, try changing the brand of gasoline. If this does not correct the problem, consult your Toyota dealer. ■...
Page 482 Non-recommendation of the use of gasoline containing MMT Some gasoline contains an octane enhancing additive called MMT (Methylcy- clopentadienyl Manganese Tricarbonyl). Toyota does not recommend the use of gasoline that contains MMT. If fuel containing MMT is used, your emission control system may be adversely affected.
Page 483 9-1. Specifications NOTICE ■ Notice on fuel quality ● Do not use improper fuels. If improper fuels are used, the engine will be damaged. ● Do not use leaded gasoline. Leaded gasoline can cause damage to your vehicle’s three-way catalytic converters causing the emission control system to malfunction.
Page 484 9-1. Specifications Tire information Typical tire symbols Full-size tire  Compact spare tire  CAMRY_U (OM33A86U)
Page 485 9-1. Specifications Tire size (P. 515) DOT and Tire Identification Number (TIN)(P. 514) Uniform tire quality grading For details, see “Uniform Tire Quality Grading” that follows. Location of treadwear indicators(P. 403) Tire ply composition and materials Plies are layers of rubber-coated parallel cords. Cords are the strands which form the plies in a tire.
Page 486 9-1. Specifications Typical DOT and Tire Identification Number (TIN) DOT symbol Tire Identification Number (TIN) Tire manufacturer’s identifica- tion mark Tire size code Manufacturer’s optional tire type code (3 or 4 letters) Manufacturing week Manufacturing year : The DOT symbol certifies that the tire conforms to applicable Federal Motor Vehicle Safety Standards.
Page 487 9-1. Specifications Tire size Typical tire size information ■ The illustration indicates typical tire size. Tire use (P = Passenger car, T = Temporary use) Section width (millimeters) Aspect ratio (tire height to section width) Tire construction code (R = Radial, D = Diagonal) Wheel diameter (inches) Load index (2 digits or 3 digits)
Page 488 9-1. Specifications Tire section names Bead Sidewall Shoulder Tread Belt Inner liner Reinforcing rubber Carcass Rim lines Bead wires Chafer CAMRY_U (OM33A86U)
Page 489 U.S. Department of Transportation. It provides the purchasers and/or prospective purchasers of Toyota vehicles with information on uniform tire quality grading. Your Toyota dealer will help answer any questions you may have as you read this information. DOT quality grades ■...
Page 490 9-1. Specifications Temperature A, B, C ■ The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat and its ability to dissi- pate heat when tested under controlled conditions on a specified indoor laboratory test wheel.
Page 491 9-1. Specifications Glossary of tire terminology Tire related term Meaning Tire pressure when the vehicle has been Cold tire inflation pres- parked for three hours or more, or has not sure been driven more than 1 mile or 1.5 km under that condition The maximum cold inflated pressure to which Maximum...
Page 492 9-1. Specifications Tire related term Meaning The combined weight of installed regular pro- duction options weighing over 5 lb. (2.3 kg) in excess of the standard items which they Production options replace, not previously considered in curb weight weight or accessory weight, including heavy duty brakes, ride levelers, roof rack, heavy duty battery, and special trim A metal support for a tire or a tire and tube...
Page 493 9-1. Specifications Tire related term Meaning A pneumatic tire in which the ply cords that extend to the beads are laid at alternate Bias ply tire angles substantially less than 90 degrees to the centerline of the tread The tire structure, except tread and sidewall Carcass rubber which, when inflated, bears the load The breaking away of pieces of the tread or...
Page 494 9-1. Specifications Tire related term Meaning A tire designated by its manufacturer as pri- Light truck (LT) tire marily intended for use on lightweight trucks or multipurpose passenger vehicles The maximum load that a tire is rated to carry Load rating for a given inflation pressure The load rating for a tire at the maximum per- Maximum load rating...
Page 495 9-1. Specifications Tire related term Meaning The linear distance between the exteriors of the sidewalls of an inflated tire, excluding ele- Section width vations due to labeling, decoration, or protec- tive bands That portion of a tire between the tread and Sidewall bead The parting of the rubber compound from the...
Page 496 9-1. Specifications Designated seating Occupant distribution Vehicle normal load, capacity, Number of in a normally loaded Number of occupants occupants vehicle 2 through 4 2 in front 2 in front, 1 in second 5 through 10 seat 2 in front, 1 in second 11 through 15 seat, 1 in third seat, 1 in fourth seat...
Page 497 Your vehicle includes a variety of electronic features that can be personalized to suit your preferences. The settings of these fea- tures can be changed by using the meter control switches, the audio system screen or at your Toyota dealer. Customizing vehicle features Changing by using the Entune Audio system ■...
Page 498 9-2. Customization Customizable features Some function settings are changed simultaneously with other func- tions being customized. Contact your Toyota dealer for further details. Definition of symbols: O = Available, —=Not available Gauges, meters and multi-information display (P. 77, 83) ■...
Page 499 9-2. Customization Customized set- Function Default setting ting Digital speedom- eter Drive information 1 — O — Distance to empty Average fuel economy (after 6 of the following reset) items: P. 85 Drive information 2 — O — Current fuel economy Trip distance (after reset)
Page 500 Settings that can be changed using the Entune Audio Plus system or Entune Premium Audio with Navigation system Settings that can be changed by your Toyota dealer Definition of symbols: O = Available, — = Not available Door lock (P. 101, 109, 487) ■...
Page 501 9-2. Customization Smart key system and wireless remote control (P. 101, 109) ■ Customized set- Function Default setting ting Operation signal — O O (Emergency flashers) Operation signal — — O (Buzzer) Operation buzzer vol- Level 5 Off to level 7 O O O Time elapsed...
Page 502 9-2. Customization Wireless remote control (P. 94, 101, 109) ■ Customized set- Function Default setting ting Wireless remote control — — O Driver’s door unlocked in one All doors Unlocking operation step, all doors unlocked in one O O O unlocked in two step steps...
Page 503 9-2. Customization Turn signal lever (P. 166) ■ Customized set- Function Default setting ting The number of times the turn signal lights flash automatically when the turn signal lever — — O 4 to 7 moved to the first posi- tion during lane...
Page 504 9-2. Customization Automatic air conditioning system (P. 331) ■ Customized set- Function Default setting ting A/C auto switch opera- Auto Manual — O O tion : If equipped Illumination (P. 339) ■ Customized set- Function Default setting ting 7.5 seconds Time elapsed before...
Page 505 9-2. Customization WARNING ■ During customization As the engine needs to be running during customization, ensure that the vehicle is parked in a place with adequate ventilation. In a closed area such as a garage, exhaust gases including harmful carbon monoxide (CO) may collect and enter the vehicle.
Page 506 9-3. Items to initialize Items to initialize The following items must be initialized for normal system opera- tion after such cases as maintenance being performed on the vehicle: Item When to initialize Reference Maintenance required reminder light (vehicles without a multi-information display) or message indicat- After the maintenance is per- P.
Page 507 National Highway Traffic Safety Administration (NHTSA) in addi- tion to notifying Toyota Motor Sales, U.S.A., Inc. (Toll-free: 1-800- 331-4331). If NHTSA receives similar complaints, it may open an investigation, and if it finds that a safety defect exists in a group of vehicles, it may order a recall and remedy campaign.
Page 508 Seat belt instructions for Canadian owners (in French) The following is a French explanation of seat belt instructions extracted from the seat belt section in this manual. See the seat belt section for more detailed seat belt instructions in English. Utilisation correcte des ceintures de sécurité...
Page 509 AVERTISSEMENT ■ Dommage et usure de la ceinture de sécurité Inspectez la ceinture de sécurité périodiquement. Vérifiez si elles ne sont pas entaillées, effilochées et que leurs ancrages ne sont pas desserrés. N’utilisez pas une ceinture de sécurité défectueuse avant qu’elle ne soit remplacée.
Page 510 SRS airbag instructions for Canadian owners (in French) The following is a French explanation of SRS airbag instructions extracted from the SRS airbag section in this manual. See the SRS airbag section for more detailed SRS airbag instruc- tions in English. ◆...
Page 511 ◆ Coussins gonflables latéraux et rideaux SRS Coussins gonflables latéraux avant SRS Participent à la protection du torse des occupants de siège avant Coussins gonflables latéraux arrière SRS Participent à la protection du torse des occupants des sièges latéraux arrière Coussins gonflables rideaux SRS ●...
Page 512 Composants du système de coussins gonflables SRS Capteurs d'impact avant Témoins indicateurs “AIR BAG ON” et “AIR BAG OFF” Système de classification de l'occupant du siège passager Témoin d'avertissement SRS avant (ECU et capteurs) Contact de boucle de ceinture Coussins gonflables de sécurité...
Page 513 Votre véhicule est équipé de COUSSINS GONFLABLES INTELLI- GENTS conçus selon les normes de sécurité américaines applicables aux véhicules à moteur (FMVSS208). L'ensemble de capteurs de coussins gonflables (ECU) régule le déploiement des coussins gon- flables sur la base des informations qu'il reçoit des capteurs, etc., indi- qués ci-dessus dans le schéma illustrant les composants du système.
Page 514 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS Respectez les précautions suivantes concernant les coussins gonflables SRS. Le non-respect de ces précautions peut occasionner des blessures graves, voire mortelles. ● Le conducteur et tous les passagers du véhicule doivent porter correcte- ment leur ceinture de sécurité.
Page 515 Un nourrisson ou un enfant trop petit pour utiliser une ceinture de sécurité doit être correctement attaché au moyen d'un siège de sécurité enfant. Toyota recommande vivement d'installer tous les nour- rissons et enfants sur les sièges arrière du véhicule et de prévoir pour eux des systèmes de retenue adaptés.
Page 516 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS ● Ne vous asseyez pas sur le bord du siège et ne vous appuyez pas contre la planche de bord. ● Ne laissez pas un enfant rester debout devant le coussin gonflable passager avant SRS ou s'asseoir sur les genoux du passager avant.
Page 517 AVERTISSEMENT ■ Précautions relatives aux coussins gonflables SRS ● Ne fixez rien et ne posez rien sur des emplacements tels que la planche de bord, la garniture du volant et la partie inférieure du tableau de bord. Ces éléments peuvent se transformer en projectiles lorsque les coussins gon- flables conducteur, passager avant et genoux SRS se déploient.
Page 518 Si les parties renfermant les coussins gonflables SRS, comme les garnitu- res du volant et des montants avant et arrière, sont endommagées ou cra- quelées, faites-les remplacer par votre concessionnaire Toyota. ● Ne placez rien sur le siège du passager avant, comme un coussin par exemple.
Page 519 SRS Ne mettez pas votre véhicule au rebut et ne procédez à aucune des modifi- cations suivantes sans consulter votre concessionnaire Toyota. Les cous- sins gonflables SRS peuvent ne pas fonctionner correctement ou se déployer (se gonfler) accidentellement, provoquant la mort ou de graves blessures.
Page 520 You lose your keys ● If you lose your keys or mechanical keys, new genuine keys or mechanical keys can be made by your Toyota dealer. (P. 97) ● If you lose your keys or electronic keys, the risk of vehicle theft increases significantly.
Page 521 What to do if... (Troubleshooting) If you think something is wrong The engine does not start (vehicles without a smart key system) ● Is the shift lever in P? (P. 155) ● Is the steering wheel unlocked? (P. 155) ● Is the battery discharged? (P.
Page 522 What to do if... (Troubleshooting) The steering wheel cannot be turned after the engine is stopped ● Vehicles without a smart key system: It is locked to prevent theft of the vehicle if the key is pulled from the engine switch.
Page 523 What to do if... (Troubleshooting) An alarm is activated and the horn sounds (vehicles with an alarm) ● Did anyone inside the vehicle open a door during setting the alarm? The sensor detects it and the alarm sounds. (P. 69) ●...
Page 524 Alphabetical index Alphabetical index Antennas (smart key system) ....114 A/C ........326, 331 Anti-lock Brake System Air conditioning filter ..... 418 (ABS) ........216 Function........ 216 (Anti-lock Brake System)..216 Warning light......447 Function ........ 216 Armrest........356 Warning light......447 Assist grips......
Page 525 Alphabetical index Back-up lights Care ........374, 377 Replacing light bulb ....433 Aluminum wheels ....375 Wattage ........ 508 Exterior ......... 374 Battery ........400 Interior ........377 Battery checking ....400 Seat belts......378 If the vehicle has discharged Cargo capacity......
Page 526 Alphabetical index Child safety ........ 53 Airbag precautions....37 Daytime running light Battery precautions..401, 492 system........169 Child restraint system ..... 54 Defogger How your child should wear Outside rear view the seat belt......30 mirrors ......327, 333 Installing child restraints ..
Page 527 Alphabetical index Door lock Doors ........101 Eco Driving Indicator ....81 Key........102 EDR (Event data recorder)..10 Smart key system ....101 Electric Power Steering Wireless remote control ..101 (EPS) ........216 Doors ........101 Function........ 216 Automatic door locking Warning light......
Page 528 Alphabetical index Engine........502 Compartment ......392 (Electric Power Steering) ..216 Engine switch....155, 157 Function........ 216 Hood ........390 Warning light......447 How to start the Event data recorder (EDR)..10 engine......155, 157 Identification number .... 501 If the engine will not start ..
Page 529 Alphabetical index Fuel ........... 180 Capacity........ 502 Hands-free system Fuel gauge......77 (for cellular phone) ..277, 290 Fuel pump shut off system..445 Head restraints ......125 Information......509 Headlights ........ 168 Refueling....... 180 Automatic High Beam Type......180, 502 system........
Page 530 Alphabetical index Interior lights......340 Switch ........340 Lane Departure Alert (LDA) ..201 Wattage ........ 508 LATCH anchors ......59 LDA (Lane Departure Alert) ..201 Lever Auxiliary catch lever....390 Jack Fuel filler door opener... 180 Positioning the jack....391 Hood lock release lever ..
Page 531 Alphabetical index Multi-information display..83 Audio system-linked ....83 Maintenance Customizing vehicle Do-it-yourself maintenance... 388 features ........ 86 General maintenance ... 383 Drive information ....85 Maintenance data ....500 Navigation system-linked..83 Maintenance Settings display ...... 86 requirements ...... 380 Switching the display ....
Page 532 Alphabetical index Paddle shift switches ....164 Radar cruise control (dynamic radar cruise control) ..... 188 Parking brake......167 Operation ......167 Radiator........398 Parking brake engaged Radio ........261 warning buzzer ... 446, 457 Rear personal lights....340 Parking brake engaged Wattage ........
Page 533 Alphabetical index Sensor Automatic headlight Safety Connect ......364 system........ 169 Seat belt reminder light... 448 Automatic High Beam Seat belts........28 system........ 177 Adjusting the seat belt .... 29 Inside rear view mirror ..130 Automatic Locking LDA (Lane Departure Retractor (ALR) ....
Page 534 Alphabetical index Steering wheel ......127 Rear window and outside Adjustment......127 rear view mirror Audio remote control defoggers switch ..327, 333 switches......246 Seat heater switches .... 337 Meter control switches .... 84 “SOS” button......364 Stop/tail lights Steering switches ...
Page 535 Alphabetical index Tire pressure warning Transmission ......162 system........404 Automatic transmission ..162 Function ........ 404 If the shift lever cannot be Initializing ......404 shifted from P ..... 486 Installing tire pressure Paddle shift switches .... 164 warning valves and S mode .........
Page 536 Alphabetical index Warning lights ......73 ABS ........447 Valet key ........94 Brake system......446 Vanity lights ......352 Charging system....446 Wattage ........ 508 Cruise control ....... 447 Vanity mirrors ......352 Electric power steering Vehicle data recording ....9 system........
Page 537 Alphabetical index Washing and waxing ....374 Weight........500 Cargo capacity...... 152 Load limits......152 Vehicle capacity weight ..500 Wheels ........416 Replacing......416 Size........506 Window lock switch ....133 Windows........133 Power windows..... 133 Rear window defogger ..... 327, 333 Windshield wipers ....
Page 538 17.0 gal. (64.35 L, 14.2 Imp. gal.) (Reference) Fuel type P. 180, 502 Cold tire inflation P. 506 pressure Engine oil capacity (Drain and refill — P. 503 reference) “Toyota Genuine Motor Oil” or equivalent Engine oil type P. 503 CAMRY_U (OM33A86U)
Page 539 2015 Entune Premium Audio ™ with Navigation and App Suite...
Page 540 Navigation Owner’s Manual. We strongly encourage you to review the Navigation Phone Compatibility Owner’s Manual, the quick reference guide and visit www.toyota.com/entune so you will have a ENTUNE - HOW TO GET STARTED better understanding of all your vehicles features and controls.
Page 541: Phone Compatibility
Apps identified by "™" or "®" are trademarks or registered trademarks of their respective companies and cannot be used without permission. See toyota.com/entune for the latest information regarding apps and services.
Page 542: Account Creation
Click on the link embedded in the email to activate your account. www.myentune.com and Terms of Service Privacy Policy © 2011 Toyota Motor Sales, U.S.A., Inc. All information applies to U.S. vehicles only. CONNECT PHONE create a personal Entune See page 7 for instructions. App account using your computer.
Page 543: Connect A Bluetooth Phone
Before you begin using the voice recognition system, it is recommended that you access "Train Voice Pairing your phone is the first step in connecting with your Toyota for hands-free calling and for audio streaming via Bluetooth. The pairing process is quick and easy: all iPhone mobile digital devices and Recognition"...
Page 544 CALLING BY VOICE RECOGNITION CALLING BY VOICE RECOGNITION DIAL BY NUMBER DIAL BY NAME If you are able to successfully transfer your phone book, you can dial by name using voice recognition. Please say the name exactly as it is entered in your phone when in the telephone screen. If you have difficulty pairing your phone, or are unable to transfer your cell phone book, please refer to the cell phone manufacturer's user guide.
Page 545 DESTINATION INPUT DESTINATION INPUT BY ADDRESS BY ADDRESS step step From the home screen, touch the map. step step Input the house number and touch Touch the desired street name. Press and enter the desired State/ followed by Province. step step step step...
Page 546 DESTINATION INPUT DESTINATION INPUT - POINT OF INTEREST (POI) NOTE ON VOICE RECOGNITION POINT OF INTEREST BY NAME The navigation system's voice recognition feature will compare your spoken words with computer-generated word patterns preprogrammed in the database. If the system does not provide your intended match, please try a different pronunciation.
Page 547 DESTINATION INPUT - POINT OF INTEREST (POI) DESTINATION INPUT - POINT OF INTEREST (POI) POINT OF INTEREST BY CATEGORY POINT OF INTEREST BY CATEGORY - VOICE RECOGNITION Quick Tip -You can search for many dining, hotel and fuel chains by name, e.g., "Find Nearby Starbucks." step step From the home screen, touch the map.
Page 548 SET HOME SET HOME step step step step Press the Set Up icon on the Touch the desired city name. Input the street name and touch Touch faceplate followed by Quick Tip - Enter the street name without prefixes such as North or the letter N. The system will display the base street name without prefixes or suffixes on the next screen.
Page 549 ADDITIONAL NAVIGATION FEATURES ADDITIONAL NAVIGATION FEATURES OPERATION OF EMERGENCY SCREEN BEEP SETTING VOICE VOLUME SEARCH AREA Prior to inputting the desired address select the State/ PRESS SET UP ICON > PRESS SET UP ICON > PRESS > Province by pressing .
Page 550 TRAFFIC TRAFFIC MY TRAFFIC ROUTES The Traffic App integrates with your navigation system to display continuously updated traffic information for over 100 markets. Just begin by pressing the APPS button and selecting My Traffic Routes lets you store favorite and previously traveled routes to check traffic conditions. To see traffic routes, touch TRAFFIC EVENT LIST AUTOMATICALLY AVOID TRAFFIC...
Page 551 WEATHER ENTUNE APP SUITE FEATURES The weather app allows you to access Doppler weather radar information. You can also check the weather Once your phone is connected via Bluetooth, Entune lets you access many useful apps. These are some of the top forecast for other cities.
Page 552 NOTES NOTES...
Page 553 00505-NAV14-ENPRE Printed in the USA 08/13...

Toyota 2015 Camry Owner's Manual

Quick Links

Accessories, spare parts and modification of your Toyota

Installation of a mobile two-way radio system

Related Manuals for Toyota 2015 Camry

Summary of Contents for Toyota 2015 Camry

Table of Contents