Page 2
IMPOR TANT NOTICE This manual has been provided for the use of authorized Yamaha Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically Yamaha Products, are already known and under- stood by the users, and have therefore not been restated.
EMX3000 SPECIFICATIONS General specifications STEREO: 300 W+300 W/4Ω @0.5% THD at 1 kHz Maximum output power 215 W+215 W/8Ω @0.5% THD at 1 kHz BRIDGE: 600 W/8Ω @0.5% THD at 1 kHz 20 Hz~20 kHz +1 dB, –3 dB @1 W output into 8Ω...
Page 4
EMX3000 Input specifications Input level Gain Actual load For use with Input terminals Connectors on mixer trim impedance nominal Max. before clip Sensitivity –60 dB (775 µV) –40 dB (7.75 mV) MIC INPUT (1–8) kΩ 50~600Ω Mics XLR-3-31 type –16 dB (123 mV) +4 dB (1.23 V)
EMX3000 PANEL LAYOUT Control Panel Channel Control Section GAIN GAIN GAIN control PEAK PEAK HIGH HIGH A/B switch (Channels 9/10~11/12 only) PEAK indicator Equalizer controls (HIGH, MID, LOW) Monitor 1/2 controls (MONI 1/2) Effect control (EFFECT) PAN (panpot) control (Channels 1~8)
EMX3000 Master Control Section MONI 1 (monitor 1) fader MONI 2 (monitor 2) fader EFFECT fader ST 1 (stereo 1) fader MONO (monaural) fader AFL (after fader listen) MONI 1 MONI 2 EFFECT ST 1 MONO Tape in Section ST (stereo) control...
Page 9
EMX3000 Power amp Section LIMITER indicator LIMITER LEVEL controls LEVEL Power amp select switch BRIDGE ST1 L ST1 R MONI 1 MONO MONO (BRIDGE) POWER AMP Other indicators and controls Peak level indicator POWER indicator PEAK PHANTOM (+48V) switch and indicator...
EMX3000 Rear panel SPEAKERS SPEAKERS (speaker output) jacks MONO MONI 1 POWER switch AC inlet BRIDGE AC IN POWER CIRCUIT BOARD LAYOUT PWR2 PWR2 PWR1 MAIN INPUT OUTPUT ST 1 11 L FOOT SW +4dB TAPE -10dBV -10dBV 10 R...
EMX3000 DISASSEMBLY PROCEDURE Panel Assembly and Bottom Assembly (Manhour requirement: 5 min.) 1-1. After removing the six (6) screws marked [90] and six (6) screws marked [100], lift the rear side of the assembly and remove it from claws on the front. (Fig. 1)
Page 15
EMX3000 [P50] [P50] [P70] [P70] [P70] [P50] [P40] [P40] MAIN [P40] [P40] [P70] [P70] [P40] [P70] [P40] [P70] [P40]: Flat Head Tapping Screw-B 3.0 X 25 MFZN2BL (VV095300) [P50]: Bonding Screw-B 3.0 X 8 MFZN2BL (VN413300) [P70]: Bind Head Tapping Screw-B 3.0 X 6 MFZN2BL (EP600230) Fig.2...
Page 16
EMX3000 Power transformer (Manhour requirement: 10 min.) 7-1. Remove the panel assembly and the bottom assembly. (See Procedure 1.) 7-2. Remove the hexagonal bolt. The power transformer can then be removed. (Fig. 3) (See Fig.3 for drawing direction of wiring assembly.)
EMX3000 LSI PIN DESCRIPTION ZFX-2 (XY297A00) CPU DSP: IC105 NAME FUNCTION NAME FUNCTION AXLR2 Audio Data Transmitt Unit 2/3 Left and Right Channel Frame Frequency Signal Audio Data Receive Unit 1 Data Input External Memory and I/O Data Bus Audio Data Receive Unit 2 Data Input...
Page 18
EMX3000 PCM3001E/2K (X0053A00) ADA DSP: IC104 NAME FUNCTION NAME FUNCTION VINL VOUTL ADC Analog Input, Lch DAC Analog Output, Lch Vcc1 LRCIN ADC Analog Power Supply Sampling Clock Input (fs) AGND1 ADC Analog GND BCKIN Bit Clock Input VREFL ADC Reference decouple, Lch...
EMX3000 CIRCUIT BOARDS MAIN Circuit Board INPUT LINE LINE LINE LINE LINE LINE LINE LINE INSERT INSERT INSERT INSERT 9/10 11/12 GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN GAIN...
Page 21
EMX3000 OUTPUT FOOTSW CNM01: to PWR1-CN102 TAPE MONO LINE L(MONO) MONI1 MONI2 EFFECT R ST-SUB1 R ST-SUB2 C-R/PHONES 9/10 11/12 C-R/PHONES POWER PEAK TAPE IN ST TAPE IN ST TAPE IN ST MONI 1 MONI 1 MONI 1 GAIN GAIN...
Page 24
EMX3000 DSP Circuit Board CN102: to PWR1-CN101 CN101: to MAIN-CNM04 Component side Pattern side 3NA-V698320...
Page 25
EMX3000 PWR1 Circuit Board CN103: to PWR2 2/3 W301RE W301WH W301BE W301BL CN105: to Transformer CN106: to PWR2 3/3 W302RE W302BL W302BE Component side 3NA-V698330...
Page 26
EMX3000 PWR2 1/3 Circuit Board to Transformer POWER ON/OFF Component side AC IN to PWR1 to PWR1 to PWR1 to PWR1 PWR2 2/3 Circuit Board -CN103 4 -CN103 3 -CN103 2 -CN103 1 BRIDGE R/MONO L/MONO SPEAKERS Component side PWR2 3/3 Circuit Board...
Page 27
EMX3000 INSPECTIONS A. INSPECTION OF MIXER SECTION PREPARATIONS • Unless otherwise specified, the signal to be applied should be 1kHz, -70dBs sine wave and the signal source impedance should be 150 ohm. Also, the load resistance at each output terminal should be of the following values.
Page 28
EMX3000 1-7 POWER AMP POWER AMP switch ST1L-ST1R POWER AMP (L/BRIDGE, R) level control Minimum 1-8 PHANTOM PHANTOM switch 1-9 Measuring equipment • The oscillator connected to the balanced type input terminal should be balanced output type with 150 ohm output impedance.
Page 29
EMX3000 • In the state as described in 1 above, input the signal of the following level to MIC IN of CH1 and turn on each AFL switch. Then check that the output as described in [Table 2-5] is obtained at C-R/PHONES OUT (L, R).
Page 30
EMX3000 DISTORTION FACTOR • In the state as described in 1, check that the distortion factor when +14dBs output is obtained at each output terminal is 0.1% or less (except for REC OUT and INSERT OUT). • In the case of C-R/PHONES OUT, set the 12 o’clock point of the level control to the Norminal position and the master fader control to 5 on the scale.
Page 31
EMX3000 B. INSPECTION OF POWER AMPLIFIER INSPECTION AT ST1L-ST1R PREPARATIONS • Input terminal: ST SUB IN 1 L/MONO • POWER AMP Switch : ST1L-ST1R • POWER AMP (L/BRIDGE, R) level control:MAX • Output terminal: SPEAKER L (1), SPEAKER R (1) •...
Page 32
EMX3000 10 PROTECTION CIRCUIT • With a signal input to POWER AMP IN (L), clip the output waveform of the 10Hz signal and check that the protection circuit functions to prevent the relay from opening. • Check that the protection circuit functions within 2 seconds to shut off the output when a 1Hz, Vp-p=10V(13.2dBs) signal is input and the output is restored automatically within 5 seconds when the input signal is stopped.
EMX3000 EMX3000 CIRCUIT DIAGRAM 1/9 ( MAIN 1/5 ) ( from P.C5-F6 ) MAIN NJM2068L-D OP AMP OP AMP OP AMP OP AMP OP AMP NJM2068L-D NJM2068L-D OP AMP OP AMP OP AMP OP AMP OP AMP NJM2068L-D NJM2068L-D OP AMP...
EMX3000 EMX3000 CIRCUIT DIAGRAM 2/9 ( MAIN 2/5 ) ( from P.C1-H6 ) NJM2068L-D OP AMP OP AMP OP AMP OP AMP OP AMP NJM2068L-D NJM2068L-D OP AMP OP AMP OP AMP OP AMP OP AMP NJM2068L-D NJM2068L-D OP AMP...
EMX3000 EMX3000 CIRCUIT DIAGRAM 3/9 ( MAIN 3/5 ) ( from P.C2-H6 ) OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP OP AMP...
EMX3000 EMX3000 CIRCUIT DIAGRAM 7/9 ( PWR1 1/2 ) PWR1 OP AMP ( to P.C8-A2 ) OP AMP ( to P.C8-A2 ) ( to P.C8-A3 ) to DSP-CN102 (P.C6-G2) ( from P.C8-E3 ) to MAIN-CNM01 ( from P.C8-E5 ) (P.C4-F1) ( from P.C8-F4 )
Page 48
EMX3000 EMX3000 CIRCUIT DIAGRAM 8/9 ( PWR1 2/2 ) ( from P.C7-F4 ) ( from P.C7-F2 ) ( from P.C7-F4 ) ( from P.C7-F2 ) ( from P.C7-F3 ) ( from P.C7-F4 ) ( to P.C7-F3 ) CN106: to PWR2 3/3...
Page 49
EMX3000 EMX3000 CIRCUIT DIAGRAM 9/9 ( PWR2 1/3 , 2/3 , 3/3 ) PWR2 to PWR1-CN106-1Pin (P.C8-G4) PWR2 to PWR1-CN106-2Pin (P.C8-G4) to PWR1-CN106-3Pin (P.C8-G4) PWR2 L/MONI1 R/MONO SPEAKERS POWER ON/OFF AC CORD common transformer 38CC1-8818805 EMX3000 EMX3000...
POWERED MIXER PARTS LIST CONTENTS OVERALL ASSEMBLY ..........2 ELECTRICAL PARTS ..........5 Notes : DESTINATION ABBREVIATIONS A : Australian model M : South African model B : British model O : Chinese model C : Canadian model Q : South-east Asia model D : German model T : Taiwan model E : European model...