Sony D-F200 Service Manual
Sony D-F200 Service Manual

Sony D-F200 Service Manual

Fm/am portable cd player
Hide thumbs Also See for D-F200:

Advertisement

SERVICE MANUAL
Ver 1.0 2002. 05
CD player
System
Compact disc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 780 nm
Emission duration: Continuous
Laser output: Less than 44.6 µW (This output
is the value measured at a distance of 200 mm
from the objective lens surface on the optical
pick-up block with 7 mm aperture.)
D-A conversion
1-bit quartz time-axis control
Frequency response
20 – 20,000 Hz +1/–3 dB
(measured by JEITA CP-307)
Output (at 4.5 V input level)
Headphones (stereo minijack)
• D-F200:
Approx. 5 mW + Approx. 5 mW
at 16 ohms
• D-F201:
Approx. 5 mW + Approx. 5 mW
at 16 ohms (Except FR model)
Approx. 0.2 mW + Approx. 0.2 mW
at 16 ohms (FR model)
Radio
Frequency range
• D-F200, F201 (CND, E13, E92, AUS,
MX, AR): (STEP switch)
9 kHz step:
FM: 87.5 – 108.0 MHz
AM: 531 – 1,710 kHz
10 kHz step:
FM: 87.5 – 108.0 MHz
AM: 530 – 1,710 kHz
• D-F201 (AEP, UK, FR, CET, CH):
FM: 87.5 – 108.0 MHz
AM: 531 – 1,602 kHz
Sony Corporation
9-874-005-01
2002E0400-1
Personal Audio Company
© 2002.05
Published by Sony Engineering Corporation
D-F200/F201

SPECIFICATIONS

Antenna
FM: Headphones/earphones cord antenna
AM: Built-in ferrite bar antenna
General
Power requirements
For the area code of the model you purchased,
check the upper left side of the bar code on the
package.
• Two LR6 (size AA) batteries: 3 V DC
• AC power adaptor (DC IN 4.5 V jack):
US/CND/E92/MX model: 120 V, 60 Hz
AEP/E13/FR/CET model: 220 – 230 V,
50/60 Hz
UK model: 230 – 240 V, 50 Hz
AUS model: 240 V, 50 Hz
CH/AR model: 220 V, 50 Hz
Battery life* (approx. hours)
(When you use the CD player on a flat and stable
surface.)
Playing time varies depending on how the CD player
is used.
When using
ESP
on
off
Two sony alkaline
31
33
batteries LR6(SG)
(produced in Japan)
* Measured value by the standard of JEITA
(Japan Electronics and Information Technology
Industries Association).
** Charging time varies depending on how the
rechargeable battery is used.
FM/AM PORTABLE CD PLAYER
Canadian Model
Australian Model
Chinese Model
Model Name Using Similar Mechanism
CD Mechanism Type
Optical Pick-up Name
Operating temperature
5°C – 35°C (41°F – 95°F)
Dimensions (w/h/d) (excluding projecting
parts and controls)
Approx. 161 × 26.3 × 130.3 mm
(6
× 1
3/8
1/16
Mass (excluding accessories)
Approx. 210 g (7.5 oz.)
Supplied accessories
For the area code of the location in which you
purchased the CD player, check the upper left
side of the bar code on the package.
Headphones/earphones (1)
AC power adaptor (1) (D-F201)
Design and specifications are subject to change
without notice.
• Abbreviation
CND : Canadian model
E13 : AC 220 – 230V area in E model
E92 : AC 120V area in E model
AUS : Australian model
RADIO
CH : Chinese model
on
FR
: French model
70
CET : East European & CIS model
MX : Mexican model
AR : Argentina model
US Model
D-F200
AEP Model
UK Model
E Model
D-F201
D-EQ550
CDM-3125ER
DAX-25E
× 5
in.)
1/4
1

Advertisement

Table of Contents
loading

Summary of Contents for Sony D-F200

  • Page 1: Specifications

    AR : Argentina model * Measured value by the standard of JEITA Frequency range (Japan Electronics and Information Technology • D-F200, F201 (CND, E13, E92, AUS, Industries Association). MX, AR): (STEP switch) ** Charging time varies depending on how the 9 kHz step: rechargeable battery is used.
  • Page 2: Table Of Contents

    LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
  • Page 3: Service Note

    D-F200/F201 SECTION 1 SERVICE NOTE NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK detection lever OR BASE UNIT The laser diode in the optical pick-up block may suffer electro- static breakdown because of the potential difference generated by the charged electrostatic load, etc. on clothing and the human body.
  • Page 4: General

    D-F200/F201 SECTION 2 GENERAL This section is extracted from instruction manual. Locating the controls For details, see pages in parentheses. CD player (front) 1 i (headphones) 8 u (play/pause) jack button 2 OPEN button 9 x (stop) •RADIO OFF button q;...
  • Page 5: Disassembly

    D-F200/F201 SECTION 3 DISASSEMBLY • The equipment can be removed using the following procedure. 3-2. UPPER LID ASSY 3-1. CABINET (UPPER) ASSY (Page 5) (Page 5) 3-3. MAIN BOARD, MD ASSY 3-4. OPTICAL PICK-UP, MOTOR (Page 6) (Page 6) Note : Follow the disassembly procedure in the numerical order given.
  • Page 6: Main Board, Md Assy

    D-F200/F201 3-3. MAIN BOARD, MD ASSY Note: When installing, fit the knob (HOLD) and S803. 4 MD assy 1 CN501 7 MAIN board 3 CN503 2 CN502 5 S812 6 S813 battery terminal (–) battery terminal (+.–) S803 cabinet (lower) sub assy knob (HOLD) 3-4.
  • Page 7: Electrical Adjustments

    D-F200/F201 SECTION 4 ELECTRICAL ADJUSTMENTS TUNER SECTION 0 dB = 1 µV FM FREQUENCY COVERAGE CHECK • FM Section Setting: Frequency Display 87.5 MHz 108 MHz RADIO ON•BAND/MEMORY button : FM + 4.0 V STEP switch : 10k Reading on Digital voltmeter 3.0 ±...
  • Page 8: Cd Section

    D-F200/F201 Adjustment Location: – MAIN BOARD (SIDE A) – CN501 AM IF ADJ RF-IN FM TRACKING ADJ TP81 IC51 CT3 L4 AM TRACKING CD SECTION CD section adjustments are done automatically in this set. In case of operation check, confirm that focus bias.
  • Page 9: Diagrams

    D-F200/F201 SECTION 5 DIAGRAMS 5-1. IC PIN DESCRIPTIONS • IC51 TC9327AF-631 (TUNER PLL, LCD DRIVER) Pin No. Pin Name Pin Description 1 to 4 COM1 to 4 LCD driver signal output 5 to 20 S1 to 16 LCD driver signal output...
  • Page 10 D-F200/F201 Pin No. Pin Name Pin Description AM IN AM oscillation signal input VDD (1.8-2.2V) — Power supply pin RESET Power reset signal input XOUT Crystal oscillation signal output (75 kHz) Crystal oscillation signal input (75 kHz) — Crystal oscillation signal pin VLCD —...
  • Page 11 D-F200/F201 Pin No. Pin Name Pin Description PDM signal output for R-ch headphone to the headphone amplifier (IC302) Not used (open) HVDD — Power supply terminal (for headphone) XVDD — Power supply terminal (for master clock) XTAI System clock input terminal (16.9344 MHz) XTAO System clock output terminal (16.9344 MHz)
  • Page 12 D-F200/F201 Pin No. Pin Name Pin Description FFDR Focus servo drive signal (+) output to the TB2125F (IC401) TRDR Tracking servo drive signal (–) output to the TB2125F (IC401) TFDR Tracking servo drive signal (+) output to the TB2125F (IC401) SRDR Sled servo drive signal (–) output to the TB2125F (IC401)
  • Page 13 D-F200/F201 • IC801 TMP88CM22AF-Z5TU1 (SYSTEM CONTROL) Pin No. Pin Name Pin Description — Ground PWRSW Headphone AMP IC power switch signal output FOK I Focus OK signal input from DSP IC. (“L”: NG, “H”: OK) AGCPWM O AGC control pulse signal output...
  • Page 14 D-F200/F201 Pin No. Pin Name Pin Description BASS1 O Not used. (Fixed at “H” in this set) BASS2 O Not used. (Fixed at “H” in this set) LCDREQ O LCD display request signal output 54 to 64 SEG10 to 0 Not used in this set.
  • Page 15: Block Diagram -Cd Section

    D-F200/F201 5-2. BLOCK DIAGRAM — CD SECTION — MAIN BOARD (1/3) DIGITAL SIGNAL PROCESSOR, DIGITAL SERVO PROCESSOR IC601 DETECTOR CN501 WDCK WFCK RFDC RFAC D-RAM XTAO IC602 XTAI VCC1 +2V D0-D3 OP-STB RFAC FOCUS/TRACKING COIL DRIVER, D0-D3 OP-SW SPINDLE/SLED MOTOR DRIVE...
  • Page 16: Block Diagram -Tuner Section

    D-F200/F201 5-3. BLOCK DIAGRAM — TUNER SECTION — MAIN BOARD ( 2/3 ) A MUTE DC/DC CONVERTER TU VCC MUTE (Page 15) CD-L CD-R R-CH TU VCC AM OSC FM/AM FRONT-END, IF DET,MPX FERRITE-ROD MIX-OUT ANTENNA HEADPHONE AMP RV301 RF-IN...
  • Page 17: Block Diagram -Power Supply Section

    D-F200/F201 5-4. BLOCK DIAGRAM — POWER SUPPLY SECTION — MAIN BOARD (3/3) POWER CONTROL IC401 (3/3) STNG HIGH/BATT SWITCH (Page 16) Q409 INP1 XDCDT (Page 16) DTC1D SWITCHING VLGO1 POWER B+ +3V CIRCUIT 2 FOCUS/TRACKING COIL DRIVER SPINDLE/SLED MOTOR DRIVER...
  • Page 18: Printed Wiring Board -Main Section

    D-F200/F201 5-5. PRINTED WIRING BOARD — MAIN SECTION — • Semiconductor Location (Side A) Ref. No. Location Common Note on Schematic Diagram: • All capacitors are in µF unless otherwise noted. pF: µµF 50 WV or less are not indicated except for electrolytics D301 and tantalums.
  • Page 19 D-F200/F201 • Refer to page 18 for Common note on Printed Wiring Board. TP803 TP815 D601 R633 IC602 TP807 R831 R635 R640 C632 R830 TP814 IC801 TP632 R638 R829 TP634 R813 R637 C639 R631 R634 US,CND,E92,AR, C805 R824 R636 MX,E13 MODEL...
  • Page 20: Schematic Diagram -Main Section (1/3)

    D-F200/F201 5-6. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 23 for IC Block Diagram. • Refer to page 18 for Common Note on Schematic Diagram. TP59 TP10 • Waveforms (CD play mode) TP81 500mV/div 10µsec/div 1V/div 0.2µsec/div...
  • Page 21: Schematic Diagram -Main Section (2/3)

    D-F200/F201 5-7. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 18 for Common Note on Schematic Diagram. • Refer to page 22 for Waveforms. R646 R210 D602 TP626 R622 TP627 R110 (Page 22) R645 C640 CN501 L604...
  • Page 22: Schematic Diagram -Main Section (3/3)

    D-F200/F201 5-8. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 23, 24 for IC Block Diagrams. • Refer to page 18 for Common Note on Schematic Diagram. TP416 TP404 C441 Q406 L406 L408 L407 R410 R445 R449...
  • Page 23: Ic Block Diagrams

    D-F200/F201 5-9. IC BLOCK DIAGRAMS IC1 TA2149BFN RF GND FM RF FM RF RF VCC FM IN AM RF AM L/CUT MIX OUT FM OSC AM OSC BUFF BUFF 1/1 OR OSC OUT LEVEL 1/16 AM IF AF IF XST DET...
  • Page 24 D-F200/F201 IC401 TB2125F 48 47 45 44 34 33 VREF VREF VLGO1 VCPU DCIN DCIN DCIN H BRIDGE 31 MGND1 VCPU DRIVER 1 CONTROL 30 RO1 VCPU2 CHARGE PGND1 VCC1 VCPU VCPU CHGON/OFF SUB VREF VCPU 29 VD12 SAW TOOTH...
  • Page 25: Exploded Views

    D-F200/F201 SECTION 6 EXPLODED VIEWS NOTE: • The mechanical parts with no reference The components identified by • Color Indication of Appearance Parts mark 0 or dotted line with mark number in the exploded views are not supplied. Example : 0 are critical for safety.
  • Page 26: Cabinet (Lower) Section

    D-F200/F201 6-2. CABINET (LOWER) SECTION CDM-3125ER LCD1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 4-222-765-11 INSULATOR 3-231-676-01 TERMINAL (LINK 4), BATTERY * 52 A-3178-707-A MAIN BOARD, COMPLETE (US,CND,E92,MX,AR) 3-222-862-01 SPRING (TORSION) * 52 A-3178-711-A MAIN BOARD, COMPLETE (E13,AUS)
  • Page 27: Cd Mechanism Deck Section (Cdm-3125Er)

    D-F200/F201 6-3. CD MECHANISM DECK SECTION (CDM-3125ER) M502 M501 The components identified by Les composants identifiés par une mark 0 or dotted line with mark marque 0 sont critiques pour 0 are critical for safety. la sécurité. Replace only with part number Ne les remplacer que par une piéce...
  • Page 28: Electrical Parts List

    D-F200/F201 SECTION 7 MAIN ELECTRICAL PARTS LIST NOTE: • Due to standardization, replacements in • SEMICONDUCTORS The components identified by mark 0 or dotted line with mark the parts list may be different from the In each case, u : µ, for example: 0 are critical for safety.
  • Page 29 D-F200/F201 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C204 1-162-962-11 CERAMIC CHIP 470PF C601 1-162-927-11 CERAMIC CHIP 100PF C254 1-107-826-11 CERAMIC CHIP 0.1uF C602 1-162-915-11 CERAMIC CHIP 10PF 0.5PF C300 1-125-838-11 CERAMIC CHIP 2.2uF 6.3V...
  • Page 30 D-F200/F201 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 8-719-420-87 DIODE MA8130 1-469-570-21 INDUCTOR CHIP 10uH D301 8-719-072-70 DIODE MA2ZD14001S0 L310 1-216-295-11 SHORT CHIP D304 8-719-059-53 DIODE MA3J14700LSO L311 1-410-389-31 INDUCTOR CHIP 47uH D305 8-719-044-74 DIODE MA792WK-TX...
  • Page 31 D-F200/F201 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 1-216-849-11 METAL CHIP 220K 1/10W 1-216-845-11 METAL CHIP 100K 1/10W 1-216-833-11 METAL CHIP 1/10W (AEP,UK,CH,FR,CET) 1-216-849-11 METAL CHIP 220K 1/10W 1-216-845-11 METAL CHIP 100K 1/10W 1-216-817-11 METAL CHIP...
  • Page 32 D-F200/F201 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R433 1-218-903-11 METAL CHIP 220K 0.5% 1/10W R634 1-216-864-11 METAL CHIP 1/10W R434 1-218-903-11 METAL CHIP 220K 0.5% 1/10W R635 1-216-833-11 METAL CHIP 1/10W R435 1-216-829-11 METAL CHIP 4.7K...
  • Page 33 D-F200/F201 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark S802 1-786-369-11 SWITCH, SLIDE (AVLS) ACCESSORIES S803 1-762-078-11 SWITCH, SLIDE (HOLD) ************ S804 1-786-369-11 SWITCH, SLIDE (EPS) S805 1-692-014-11 SWITCH, KEYBOARD (u) 1-476-845-11 ADAPTOR, AC (AC-ES455) (AEP,E13,FR,CET)
  • Page 34 D-F200/F201 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision...

This manual is also suitable for:

D-f201

Table of Contents