Setting Video And Audio Input Sources [Audio Video] - Panasonic AG-HMX100P Operating Instructions Manual

Example of DIRECT PATTERN KEY screen
POS. X 128 Y 128
Z 196
EVENT ME TIME
00 1:00
E F
DIRECT PATTERN KEY
PATTERN WIDTH
EDGE HARD
EFFECTS
OFF
KEY EMPTY
LEARN
9000
Up to six key patterns can be stored.
It is also possible to change the settings for the edge
of each pattern or set and store effects for each pattern
( page Vol.2-5).
To use the factory default settings
1
Select [DEFAULT] using the rotary 2 control,
and press the key.
2
When the message [OK?] appears, press the
key.
To stop the setting process, press the
while holding down the SHIFT key.
The display returns to the [SETUP] menu screen.
Setting Video and Audio Input
Sources [AUDIO VIDEO]
The [AUDIO VIDEO] submenu of the [SETUP] menu is used
to select video and audio input sources to be processed or
mixed.
Rotary 1 Rotary 2 Rotary 3
AUDIO INPUT
VIDEO SETUP
SETUP
DEFAULT
V-LINK
* VIDEO1 and VIDEO2 are displayed as choices when the
1
current system format is SD ( page 19). HDMI1 and
HDMI2 are displayed when the current system format is
HD.
24
PATTERN INT
3002 WHT
ENTER TO EXIT
COLOR K LEVEL
16 WHITE 255
SETUP
key
Rotary 4 Rotary 5
AUX WFM
SDI1 SDI1
SDI1 SDI1
SDI2 SDI2
SDI3 SDI3
SDI4 SDI4
HDMI1 HDMI1
(VIDEO1)* (VIDEO1)*
1 1
HDMI2 HDMI2
(VIDEO2)* 1 (VIDEO2)* 1
PGM DVI-I
PVW
M VIEW
The video and audio input source settings are stored
individually for the following three cases.
• When the system format setting is SD (
• When the system format setting is HD (
• 3D mode setting is other than [OFF].
The stored settings are read out each time the system
format is changed.
To display the Audio/Video Input Source
Setting screen
1
Set [INPUT] to [SETUP] using the rotary 2
control, and press the
2
When the message [OK?] appears, press the
key again.
The Audio/Video Input Source Setting screen
appears.
To cancel the setting, press the
holding the SHIFT key.
The display returns to the [SETUP] menu screen.
Audio/Video Input Source Setting screen
Rotary 1 Rotary 2 Rotary 3
1 V S-1 SDI
2 V S-2 SDI
3 V S-3 SDI
4 V S-4 SDI
5 V S-1 HDMI
6 V S-2 HDMI
7 V S-1 DVI-I
8 V S-2 SDI
V S-1 SDI
V S-2 HDMI
V S-3 VIDEO
V S-4 DVI-I
 NOTE
If the 3D mode is set to [MODE3-M] or [MODE3-S], neither
[INPUT] item nor setting screen appears.
To select the number of an input source
Use one of the following two methods:
• Select the input source number on the Audio/Video Input
Source Setting screen using the rotary 1 control. The
rotary 1 control allows you to select the program input
source number of bus A.
• Use the A/PROG or B/PRESET bus source selector
buttons.
To select sources 5 to 8, press the corresponding A/
PROG (or B/PRESET) bus source selector button while
holding down the SHIFT button.
The pressed button flashes.
 page 19).
 page 19).
key.
key while
Rotary 4 Rotary 5
A S-1 SDI
A S-2 SDI
A S-3 SDI
A S-4 SDI
A S-1 HDMI
A S-2 HDMI
A S-1 ANALOG
A S-2 ANALOG
A S-1 SDI
A S-2 HDMI
A S-3 ANALOG
A S-4