Sony SNC-WR632 Installation Manual

4-474-023-12(1)
Network Camera
Installation Manual
Before operating the unit, please read this manual thoroughly and
retain it for future reference.
SNC-WR632/WR602
© 2013 Sony Corporation
Printed in China
A

 
B
 
      
C
  
Printed side

About the Manuals
Installation Manual (this document)
This Installation Manual describes the names and functions of parts and controls
of the Network Camera, gives connection examples and explains how to set up
the camera. Be sure to read the Installation Manual before operating.
SNC easy IP setup Guide (stored in the CD-ROM)
User's Guide/Application Guide (Web)
The User's Guide describes how to set up the camera and how to control the
camera via a Web browser.
After installing and connecting the camera correctly, operate referring to this
User's Guide.
Using the software
The supplied CD-ROM includes the setup program for assigning an IP address.
The information for how to set up an IP address is also included in the disc in PDF
format.
User's Guide and Application Guide can be downloaded from the disc, or the
following URL:
http://www.sony.net/ipela/snc
Using the CD-ROM manual
The manual can be read on a computer with Adobe Reader installed.
You can download Adobe Reader free from the Adobe website.
1
Open the index.html file in the CD-ROM.
2
Select and click on the manual that you want to read.
Note
If you have lost or damaged the CD-ROM, you can purchase a new one from your
Sony dealer or Sony service counter.
Adobe and Acrobat Reader are trademarks of Adobe Systems Incorporated in the
United States and/or other countries.
Assigning the IP address
Assign the IP address using the setup program in the supplied CD-ROM.
For details on how to set up the IP address, see SNC easy IP Setup Guide.
Location and Function of Part
Camera (Front)
 Top sunshade
 Dome cover
 Sunshade
Top Unit (Bottom)
 Reset switch
This switch returns the setting of the device to the factory default setting.
1. Move the INIT switch in the direction indicated by  and connect with
camera.
2. Turn on power and wait 1 minute. After the initialization is completed, the
camera starts.
3. Check that the camera has started and turn off the power to remove camera.
4. Move the INIT switch back to its original position.
Notes
ˎ
Resetting the device removes all customized settings. It is recommended
that users save the settings as necessary. Instructions on how to save
settings are available in the User's Guide.
ˎ
The reset switch should always be returned to its original position.
Otherwise your device is reset to its factory default setting whenever it is
turned on.
 Camera connection terminal
Connect to the camera connection terminal of the camera.
 AC 24 V (power input) terminal
Use the supplied AC connector to connect to the 24 V AC power supply system.
Pin name
Pin No.
AC24V
1 AC24V+
2 Frame Ground
3 AC 24V-
Note
Be sure to connect the Frame Ground to the specified terminal.
 I/O (Input/Output) port
Provides four sensor inputs and two alarm outputs.
1 8
7 14
Pin name
Pin Pin
Pin name Color
RS422/ RS485
No. No.
RS485(Full) (Half )
1 Alarm Out 1- Blue 8 Rx-
2 Alarm Out 1+ Blue 9 Rx+
Tx-/Rx-
3 Sensor in 4 Yellow 10 Tx-
4 Sensor in 3 Orange 11 Tx+ Tx+/Rx+
5 Sensor in 2 Red 12 GND
6 Sensor in 1 Brown 13 Alarm Out 2-
14
7 GND Black Alarm Out 2+
Note
For details about functions and settings, see the user's guide.
  LAN (network) port (RJ-45)
Connect to a 10BASE-T or 100BASE-TX network using a network cable (UTP,
category 5).
 Harness holder
Attach the supplied band mount.
 (video output) terminal
Outputs a composite video signal. Use the supplied monitor cable to connect to
the camera.
 (microphone input) terminal (minijack, monaural)
Connect a commercially available microphone.
 (line output) terminal (minijack, monaural)
Connect to a commercially available speaker with a built-in amplifier.
Camera (Top)
 Camera connection terminal
Connect to the camera connection terminal of the top unit.
 Rating Label
This label shows the name of device and its electric rating.
 Built-in wire rope
The wire rope is used for fall-prevention.
 SD memory card slot
This slot is used for an optional SD memory card.
Images captured by the camera can be stored into an inserted memory card.
Be sure that the printed side of a memory card and the product specifications
label face in the same direction, and then insert the card firmly into the slot. (a)
This unit only supports memory card formats compatible with the SD/SDHC
standards.
Note
For information about Sony-approved SD memory cards, contact your Sony
dealer.
Connection
Connecting to the Network
Connect the LAN port of the camera unit to a router or hub in the network using
the network cable (not supplied).
Connecting the Power Source
The following power sources can be used.
ˎ HPoE+ 4 line power-supply
ˎ 24 V AC
Notes
ˎ Do not turn off the camera immediately after turning it on. Wait for at least five
minutes before turning off the camera.
ˎ If power is supplied by an HPoE+ system, do not install the wiring for 24 V AC.
Perform grounding of the frame ground only.
HPoE+ 4 line power-supply
The power is supplied by using PD9501G of PowerDsine or a similar power supply
device via a network cable.
For details, refer the manual of the power supply device.
Note
If the power is supplied by HPoE+, the integrated heater is not available. Use the
camera in the activation temperature range of 0 °C to 50 °C (32 °F to 122 °F).
Connecting to a 24 V AC power source supply
Connect the 24 V AC power supply system to the power input terminal of the
camera. The AC power cable is not supplied.
ˎ Use a 24 V AC power source isolated commercial power supply.
ˎ The usable voltage range is as follows:
24 V AC: 21.6 to 26.4 V
ˎ Use a UL cable (VW-1 style 10368) for 24 V AC connection.
Recommended power cable
24 V AC
Cable(AWG) #22 #20
Maximum cable length
5 (16.4) 8 (26.2)
(m (feet))
Connecting the I/O Cable
Wiring diagram for sensor input
Mechanical switch/open collector output device

Camera inside Outside
3.3 V
10 kohms

2.2 kohms
10 kohms
Sensor Input 1, 2, 3, 4
Mechanical
switch
10 kohms
GND
GND GND GND
Wiring diagram for alarm output
Camera inside Outside
24 V DC
Alarm Output +
Magnet relay
24 V AC
24 V DC, Circuit example
1 A or less
Alarm Output –
GND
Color
Yellow
Orange
Red
Brown
Black
Purple
Purple

#18 #16
15 (49.2) 21 (68.9)
or
Open collector
output device
R
(continued on the reverse side)