[LAMP POWER] ..........22 under copyright law. [IMAGE FLIP] ............. 22 • Sony assumes no responsibility for damages, loss of [3D GAMMA SELECT] ........22 income, or any claims from a third party arising out [SINGLE 3D ADJUST] ........22 of use of the system.
SRX-T615. Installation Manual This includes instructions on how to install and configure initial settings for the SRX-T615, and how to perform adjustments for devices. Refer to this manual whenever you want to change settings or readjust the devices after installation.
Lens attachment point (page 16). Attach a lens (not supplied) here. Left side For details on lens attachment or replacement, contact your dealer or your local Sony representative. Rear Connectors a Lamp access panel (lamp grill) / intake vent / air filter...
Intake vent / air filter For details on lamp replacement or filter cleaning, contact your dealer or your local Sony representative. A Connectors a NETWORK connector (RJ-45 modular jack) c RS-232C connector (D-sub 9-pin, female) Connect a LAN cable (not supplied) here and use it to...
[Reset]: Allows you to reset the password required for authentication when displaying the For details, contact your dealer or your local [SERVICE] and [SETTING] tabs. Sony representative. This menu only appears when a user with [Quit]: Quits SRX Controller. administrator privileges has started SRX Controller.
[FUNCTION] For details on the [SERVICE] and [SETTING] tabs, contact your dealer or your local Sony Select the FUNTION you want to use. representative. You can register adjustments and settings configured for the projector in the SRX Controller screen to...
Page 8
[ON]: Temporarily blocks the entire image that is projected onto the screen (i.e., a black screen will be displayed). [OFF]: Displays the image. d [CUT OFF] area Use this to display 3D images. For details, contact your dealer or your local Sony representative. Parts Identification...
Locations subject to high temperature and Preparation humidity Precautions for Installation and Use Unsuitable Environments Locations subject to sudden temperature Do not install the projector in the following types of changes environments. Doing so may result in malfunctions or damage to the projector. Poorly ventilated locations Sudden temperature changes in an enclosed space where the projector is installed will result in condensation, which...
Unsuitable Operating Conditions Installing SRX Controller Do not operate the projector under the following on the Controller PC conditions. Install the SRX Controller software on the computer you Projector tilted to the left or right will use to control the projector. If a previous version of SRX Controller is already installed on the computer, uninstall the previous version beforehand.
Read the agreement, select [I accept the terms in the Notes license agreement], and then click [Next]. The application will not run if you select [Cancel]. If you select [I do not accept the terms in the license agreement], the software will not be installed and the If the administrator password entry screen wizard will close.
When the following screen appears, click [Finish]. Connecting the Controller If you selected the [Launch the program] checkbox, SRX Controller will start immediately. Connect the controller PC to the NETWORK connector or RS-232C connector on the projector, depending on your operating environment.
Connecting to the RS-232C Connecting the Connector Projection Source Device Use a connection cable (not supplied) to connect the RS-232C connector on the projector to the RS-232C connector on the controller PC. Notes on connection • Perform connections for devices with their breakers off or with their power cords disconnected.
When running Windows XP SP3 or later Verification • If the following dialog box appears during SRX Controller startup, click [Unblock]. Startup Turn on the projector’s main power, start SRX Controller, and then start the projector. Turning On the Main Power of the Projector Raise the power switch on the rear of the projector to the on position (|) to turn on the projector.
To connect by specifying the projector’s IP Starting the Projector address Select [Network] in the [Connect] menu, enter the Click at the top right of the main screen of SRX projector’s IP address for [Projector IP Address] in the Controller. [Network] dialog box that appears, select [SRX-T600 series] for [Select Model] and then click [OK].
Turning Off the Projector Click at the top right of the main screen of SRX Controller. A confirmation screen appears. Click [OK]. The MAIN and LAMP indicators on the rear of the projector will begin to blink green to indicate that cooling is in progress.
Display the [INSTALLATION] tab, and adjust the Projection focus and viewing angle under [LENS CONTROL]. Projecting Images onto a Screen Operations for projection are performed in the SRX Controller screen. 1 Click [–] or [+] for [Focus] to adjust the focus. Turn on the main power of the projector (page 14).
Restoring the default adjustment values Set [Right] to [ON], and select [512] for [Width]. If you set [Marker] to [On], green and red lines will Click [RESET] to restore all the adjustment points to their appear at the start and end positions of blending, default values.
Select the FUNCTION you want to register in the Adjustments and Settings [FUNCTION] drop-down list. SRX Controller Adjustments and Settings Adjustments and settings are performed in the various tabs Perform adjustments and settings in each tab. of the SRX Controller screen. The current setting values will be stored to the This section describes the setting items in each tab.
Notes [PICTURE CONTROL] Tab If [Single 3D] is selected for [INPUT SELECT], signal information will not be displayed in the right eye settings You can select the input signal and adjust the picture if it is common to the left eye settings. quality in the [PICTURE CONTROL] tab.
To specify a gamma value, select [Custom] in the drop- [COLOR CONFIG.] Tab down list, click [CUSTOM], and enter a gamma value in the [Input Gamma Data] dialog box that appears. You can configure input signal settings in the [COLOR CONFIG.] tab.
HV: Flip the top and bottom, and the left and right sides of [3D GAMMA SELECT] and [SINGLE 3D ADJUST] are the image. used when projecting 3D images. For details, contact your dealer or your local Sony representative. [LENS CONTROL] Adjust the image projected onto the screen. [Zoom] Adjust the image size.
However, turning off the test pattern will restore original conditions. [SINGLE 3D] is used when projecting 3D images. For details, contact your dealer or your local Sony representative. [INSTALLATION] Tab...
30 seconds, perform verification of operation again. If the problem persists, contact your dealer or your local Sony representative. Images Usage time (%) Color Symptom Cause Solution...
Warning (severity: medium): Operation will continue, but the problem should be resolved as soon as possible. Info (severity: low) If an error message appears, contact your dealer or your local Sony representative with the message number and error message. Error (severity: high) Message No. Message...
Page 29
WARRANTY, OR FOR ANY OTHER REASON Top & Bottom 1280 × 720 59.94p/60p WHATSOEVER. • SONY WILL NOT BE LIABLE FOR CLAIMS OF Top & Bottom 1280 × 720 ANY KIND MADE BY USERS OF THIS UNIT OR Side by Side 1280 ×...