Sony BVM-E250 Operation Manual page 101

3) Chromaticity point of SMPTE RP 431-2 is not
covered in full.
4) The BVM-E170 individual chromaticity points. The
widest color space setting of the signal reproduced
by the BVM-E170
R
G
B
5) For displaying the color gamut of the wide color
space mode S-GAMUT, which is available for the
F23 or F35 Digital Cinematography Camera
Warm-up time Approx. 30 minutes
Input
SDI BNC (×2)
Input impedance: 75 ohms unbalanced
Signal format
See "Available Signal Systems" and
"Available Signal Formats" on the
Operation Manual.
Sampling frequency
3G-SDI:
Y/Cb/Cr (4:2:2)
148.5MHz/74.25MHz/74.25MHz
Y/Cb/Cr (4:4:4)
148.5MHz/148.5MHz/148.5MHz
G/B/R (4:4:4)
148.5MHz/148.5MHz/148.5MHz
HD-SDI:
Y/Cb/Cr (4:2:2)
74.25MHz/37.125MHz/37.125MHz
SD-SDI:
Y/Cb/Cr (4:2:2)
13.5MHz/6.75MHz/6.75MHz
Quantization
3G-SDI: 10 bit/sample, 12 bit/sample
HD-SDI: 10 bit/sample
SD-SDI: 10 bit/sample
HDMI HDMI (×1)
HDCP correspondence, Deep Color
correspondence
Signal format
See "HDMI/DisplayPort" of
"Available Signal Formats" on the
Operation Manual.
DisplayPort DisplayPort connector (×1)
HDCP correspondence, 18/24/30bpp
(bits per pixel) correspondence
Signal format
See "HDMI/DisplayPort" of
"Available Signal Formats" on the
Operation Manual.
Option port Four (4) ports
Signal format
x y
0.681 0.319
0.189 0.724
0.141 0.051
(Typical)
See "Available Signal Systems" and
"Available Signal Formats" on the
Operation Manual.
Parallel remote D-sub 9-pin (female) (×1)
Serial remote (LAN)
Ethernet (10BASE-T/100BASE-TX),
RJ-45 (×1)
Output
SDI BNC (×1) (monitor output)
Output signal amplitude:
800 mVp-p±10%
Output impedance: 75 ohms unbalanced
Transmission distance
3G-SDI: 70 m max.
HD-SDI: 100 m max.
SD-SDI: 200 m max.
Note
The signal from the monitor output
connector does not satisfy the ON-LINE
signal specifications.
6) When using the 5C-FB coaxial cable made by
Fujikura Ltd. or equivalent
7) When using the 5C-2V coaxial cable made by
Fujikura Ltd. or equivalent
DC 5V OUT Circle 4-pin (female) (×1)
General
Power requirements
100 V to 240 V AC,
1.2 A to 0.7 A, 50/60 Hz
24 V to 28 V DC,
4.5 A to 3.9 A
Power consumption
Approx. 110 W (AC power supply)/
approx. 100 W (DC power supply)
(maximum)
Approx. 60 W (AC power supply)/
approx. 60 W (DC power supply)
(average power consumption in the
default status)
Inrush current (1) Maximum possible inrush current at
initial switch-on (Voltage changes
caused by manual switching):
55 A peak, 15 A r.m.s. (240V AC)
(2) Inrush current after a mains
interruption of five seconds (Voltage
changes caused at zero-crossing):
36 A peak, 7 A r.m.s. (240V AC)
Operating temperature
0 °C to 35 °C (32 °F to 95 °F)
Recommended: 20 °C to 30 °C (68 °F to
86 °F)
Operating humidity
0% to 90% (no condensation)
6)
6)
7)
101
Specifications (BVM-E170)