SERVICING NOTICES ON CHECKING 1. KEEP THE NOTICES 6. AVOID AN X-RAY As for the places which need special attentions, Safety is secured against an X-ray by consider- they are indicated with the labels or seals on the ing about the cathode-ray tube and the high cabinet, chassis and parts.
ABOUT LEAD FREE SOLDER (PbF) Distinction of PbF PCB: PCBs (manufactured) using lead free solder will have a PbF printing on the PCB. (Please refer to figures.) Caution: • Pb free solder has a higher melting point than standard solder; Typically the melting point is 50°F~70°F(30°C~40°C) higher.
TABLE OF CONTENTS SERVICING NOTICES ON CHECKING ..................A1-1 HOW TO ORDER PARTS ......................A1-1 IMPORTANT ..........................A1-1 ABOUT LEAD FREE SOLDER (PbF) ..................A1-2 TABLE OF CONTENTS ......................A2-1 GENERAL SPECIFICATIONS ....................A3-1~A3-5 DISASSEMBLY INSTRUCTIONS 1. REMOVAL OF ANODE CAP ....................B1-1 2.
GENERAL SPECIFICATIONS CRT Size / Visual Size 26 inch / 656.7mmV System CRT Type Flat (16:9) Magnetic Field BV/BH +0.45G/0.18G Color System NTSC Display Capability 1080i/540p Speaker 2 Speaker Position Front Bottom Size 1.8 x 3.9 Inch Impedance Sound Output 5.0W+5.0W 10%(Typical) NTSC3.58+4.43 /PAL60Hz...
Page 6
GENERAL SPECIFICATIONS On Screen Menu Display Menu Type Icon Picture Mode(Picture preference) Brightness Contrast Color Tint Sharpness Color Temperature Display Format Cable Clear Reset Audio Bass Treble Balance Stable Sound Speakers On/Off Dolby Virtual WOW SRS 3D WOW Focus WOW Tru Bass HDMI1 HDMI2 Reset...
Page 7
Timer Back-up (at Power Off Mode) more than G-10 Remote Unit RC-KK Control Glow in Dark Remocon Back Light Remocon Remocon Format Toshiba Format Toshiba Custom Code TV:40-BFh Power Source Voltage(D.C) UM size x pcs UM-4 x 2 pcs Total Keys...
Page 8
GENERAL SPECIFICATIONS G-11 Features Auto Shut Off CABLE Power On Memory Memory(Last CH) Memory(Last Volume) V-Chip Type USA, ORION Type SRS WOW(SRS 3D/Focus/Tru Bass) Virtual Dolby Yes(Digital) Timer(On Timer /Off Timer/Sleep Timer) Aspect Cinema Mode Image Tilt Direct Input Selection Auto Search CH Lock CH Program...
Page 9
GENERAL SPECIFICATIONS G-13 Interface Switch Front Power Channel Up/Menu Up Channel Down/Menu Down Volume Up/Menu > Volume Down/Menu < Indicator Power Yes(RED) Stand-by On Timer Terminals Front Video Input = VIDEO3 Audio Input = VIDEO3 RCA x 2 S Input = VIDEO3 Other Terminal Rear Video Input(Rear1) = VIDEO1...
DISASSEMBLY INSTRUCTIONS 3. After one side is removed, pull in the opposite direction to 1. REMOVAL OF ANODE CAP remove the other. Read the following NOTED items before starting work. NOTE After turning the power off there might still be a potential Take care not to damage the Rubber Cap.
DISASSEMBLY INSTRUCTIONS When IC starts moving back and forth easily after REMOVAL AND INSTALLATION OF desoldering completely, pickup the corner of the IC using a FLAT PACKAGE IC tweezers and remove the IC by moving with the IC desoldering machine. (Refer to Fig. 2-3.) REMOVAL NOTE Put Masking Tape (cotton tape) around the Flat Package...
Page 12
DISASSEMBLY INSTRUCTIONS INSTALLATION When bridge-soldering between terminals and/or the soldering amount are not enough, resolder using a Thin-tip Take care of the polarity of new IC and then install the new Soldering Iron. (Refer to Fig. 2-8.) IC fitting on the printed circuit pattern. Then solder each lead on the diagonal positions of IC temporarily.
SERVICE MODE LIST This unit provided with the following SERVICE MODES so you can repair, examine and adjust easily. To enter to the Service Mode, press both set key and remote control key for more than 2 seconds. Set Key Remocon Key Operations Releasing of V-CHIP PASSWORD.
Page 14
WHEN REPLACING EEPROM (MEMORY) IC If a service repair is undertaken where it has been required to change the MEMORY IC, the following steps should be taken to ensure correct data settings while making reference to TABLE 1. ADDRESS DATA INIT CRT ON 0010 OEC7118A_32...
WHEN REPLACING EEPROM (MEMORY) IC Enter DATA SET mode by setting VOLUME to minimum. Press both VOL. DOWN button on the set and Channel button (6) on the remote control for more than 2 seconds. ADDRESS and DATA should appear as FIG 1. ADDRESS is now selected and should "blink".
ELECTRICAL ADJUSTMENTS 1. ADJUSTMENT PROCEDURE FUNCTION FUNCTION FUNCTION OSD H CORNER R-Y PHASE Read and perform these adjustments when repairing the CUT OFF C.PARA G-Y GAIN circuits or replacing electrical parts or PCB assemblies. H.POSI C.SAW G-Y PHASE V.POSI V.SYMM BRI.CENT CAUTION H.
Page 17
ELECTRICAL ADJUSTMENTS 2-3: FOCUS 2-6: VERTICAL CENT/ VERTICAL SIZE Receive the monoscope pattern. Receive the monoscope pattern. Press the MENU button. And, then press the LEFT/ Turn the Focus Volume fully counterclockwise once. Adjust the Focus Volume until picture is distinct. RIGHT button on the remote control until the PICTURE menu appears.
Page 18
ELECTRICAL ADJUSTMENTS 2-8: BRIGHT CENT 2-11: TRAPEZIUM Receive the monoscope pattern. (RF Input) Receive the crosshatch signal from the Pattern Generator. Set the screen mode to FULL. Press the MENU button. And, then press the LEFT/ Using the remote control, set the brightness and contrast RIGHT button on the remote control until the PICTURE to normal position.
ELECTRICAL ADJUSTMENTS 2-14: SEMSOR PARA Receive the crosshatch signal from the Pattern Generator. Press the MENU button. And, then press the LEFT/ RIGHT button on the remote control until the PICTURE menu appears. 100% Press the LEFT/RIGHT button on the remote control to 120% highlight DISPLAY FORMAT.
ELECTRICAL ADJUSTMENTS 3. PURITY AND CONVERGENCE 3-3: STATIC CONVERGENCE ADJUSTMENTS NOTE Adjust after performing adjustments in section 3-2. NOTE Receive the crosshatch pattern from the color bar Turn the unit on and let it warm up for at least 30 generator.