Sony HAP-S1 Service Manual page 35

6. The SMART data is saved as a text fi le in the USB memory.
(The fi le name is "hap_smart_data_xxxxx_yyyyy.log (xxxxx:
hard disk drive model name, yyyyy: hard disk drive serial
number))
Note 3: This fi le uses Linux newline code "LF". You should use "Internet
Explorer" or "text editor" that supports "LF" to open this fi le.
7. Rotate the [PUSH ENTER] knob to scroll the SMART data on
the liquid crystal display, and SMART ID is displayed on the
liquid crystal display.
SMART ID SMART raw value
5-4.SMART Data Read
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH
TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 100 100 040 5-4.SMART Data Read
Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 194 194 033 Pre-fail
3 Spin_Up_Time 0x0007 194 194 033 Pre-fail
Always - 1
Always - 1
4 Start_Stop_Count 0x0012 100 100 000 Old_age
Always - 140
The data was saved to USB memory
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail
Always - 0
Back to HDD Menu
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail
Offline - 0
5-4.SMART Data Read
The data was saved to USB memory
194 Temperature_Celsius
Old_age Always - 28
Back to HDD Menu
196 Reallocated_Event_Count 0x0032 100 100 000
Old_age Always - 0
The data was saved to USB memory
197 Current_Pending_Sector 0x0022 100 100 000
Old_age Always - 0
Back to HDD Menu
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000
Old_age Always - 0
The data was saved to USB memory
Back to HDD Menu
SMART ID
(Displayed characters/values in the above fi gure are example)
8. Check the SMART raw value of following SMART IDs is dis-
played on the liquid crystal display.
ID
5 Reallocated sector count
196 Reallocated event count
197 Current pending sector count
198 Offl ine scan uncorrectable sector count
9. If at least one of these ID's SMART raw value is not "0",
SMART data check is NG.
Note 4: When the SMART data check is NG, replace the hard disk drive.
0x0002 214 214 000
SMART raw value
Name
4-6. Audio
Procedure:
1. Enter the service DIAG mode.
(Refer to "1. Entering Method of The Service DIAG Mode" on
page 31)
2. Rotate the [PUSH ENTER] knob to select the "6. Audio".
3. Press the [PUSH ENTER] knob to enter the "6. Audio" mode.
6.Audio
1. Play Audio Data
2. Select Input
3. Back to Main Menu
4-6-1. Play Audio Data
It can play back various audio data.
Procedure:
1. Enter the "6. Audio" mode.
(Refer to "4-6. Audio")
2. Rotate the [PUSH ENTER] knob to select the "1. Play Audio
Data".
3. Press the [PUSH ENTER] knob to enter the "1. Play Audio
Data" mode.
(The volume control and muting function is available in this
mode)
6-1.Play Audio Data
1. 1kHz DSD 0dB
2. 1kHz PCM 0dB 32bit/48kHz
3. 1kHz PCM 0dB 32bit/44.1kHz
4. 1kHz PCM 0dB 32bit/48kHz PCM Direct
5. 1kHz PCM 0dB 32bit/44.1kHz PCM Direct
6. stop
6-1.Play Audio Data
2. 1kHz PCM 0dB 32bit/48kHz
3. 1kHz PCM 0dB 32bit/44.1kHz
4. 1kHz PCM 0dB 32bit/48kHz PCM Direct
5. 1kHz PCM 0dB 32bit/44.1kHz PCM Direct
6. stop
7. Back to Audio Check Menu
4. Select the audio data by rotating the [PUSH ENTER] knob and
press the [PUSH ENTER] knob.
Note 1: "1. kHz DSD 0dB" does not play back continuously, and stops
once after a few seconds.
Note 2: "4. 1kHz PCM 0dB 32bit/48kHz PCM Direct" and "5. 1kHz
PCM 0dB 32bit/44.1kHz PCM Direct" cannot use in this unit.
5. The selected audio data is played back.
6. To stop the audio data, rotate the [PUSH ENTER] knob to se-
lect the "6. stop" and press the [PUSH ENTER] knob.
Note 3: When checking for the "3. OPT" or "4. COAX" in the "6-2. Se-
lect Input" after playing back the "1. kHz DSD 0dB", play back
the "2. 1kHz PCM 0dB 32bit/44.1kHz" once, and then enter the
"6-2. Select Input" mode.
HAP-S1
35