Page 1
– SUMMARY – This service manual covers only the different points from the service manual, file no. 810-9903, for model SD-3109 since SD-5109 is basically the same designing as SD-3109. Please refer to the file no. 810-9903 for other information.
LASER BEAM CAUTION LABEL When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of a laser may be recceived. PREPARATION OF SERVICING Pickup Head consists of a laser diode that is very susceptible to external static electricity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened.
CONTENTS SECTION 1 GENERAL DESCRIPTIONS 1. OPERATING INSTRUCTIONS General descriptions such as location of mechanical parts and troubleshooting are the same as SD-3109. Please refer to the service manual for SD-3109 (File No. 810-9903). SECTION 2 PART REPLACEMENT AND ADJUSTMENT PROCEDURES Part replacement and adjustment procedures are the same as SD-3109.
SECTION 3 SERVICING DIAGRAMS 1. CIRCUIT SYMBOLS AND SUPPLEMENTARY EXPLANATION 1-1. Precautions for Part Replacement • In the schematic diagram, parts marked (ex. • Using the parts other than those specified shall violate the regulations, and may cause troubles such as F801) are critical part to meet the safety regulations, operation failures, fire etc.
IC615 may be requested for servicing. DATA UPDATE KIT (RS232C Interface/cable) RS-232C cable Computer (MS-DOS/PC-DOS) Fig. 3-1-6 CN601 Note: • The firmware and setup data floppy discs are not available as service parts. For more information, consult TOSHIBA service office in your area.
3. BLOCK DIAGRAMS 3-1. Overall Block Diagram Data/Control Bus DVD AV Data SP DIF Data MAIN PROCESSOR UNIT AUDIO/VIDEO OUTPUT UNIT IC503 HY512264JC-50 2M-DRAM Coaxial Digital IC202 Audio Out Buffer MSM514800C-70 TC74HCU04AF TOS Link Digital 384fs Audio ICY09 4M-DRAM Audio Out Tray Master Clock Motor...
SECTION 4 PARTS LIST SAFETY PRECAUTION The parts identified by ! ( ) mark are critical for safety. Replace only with part number specified. The mounting position of replacement is to be identical with originals. The substitute replacement parts which do not have the same safety characteristics as specified in the parts list may create shock, fire or other hazards.
5. PARTS LIST LOCATION PART NUMBER NUMBER DESCRIPTION - MECHANICAL PARTS - 79080074 Kit,Data Update FM01 79070421 Motor Assy,Feed MC01 79070426 Chassis Assy Mechanism MC14 79070429 Belt,Loading MP01 79070415 Mechanism Assy,pickup MP16 79070422 Gear MP36 79070424 Dumper,Rubber Front MP37 79070425 Dumper,Rubber Rear MP61...
Page 28
LOCATION PART LOCATION PART NUMBER NUMBER DESCRIPTION NUMBER NUMBER DESCRIPTION R822 79030035 Res,Carbon 2.7kohm J 1/6W - ELECTRICAL PARTS - R823 79030004 Res,Carbon 1kohm J 1/6W R824 79030002 Res,Carbon 10kohm J 1/6W R825 79030039 Res,Carbon 4.7kohm J 1/6W ! EU02 79085017 PC Board Assy Power...
Page 29
LOCATION PART LOCATION PART NUMBER NUMBER DESCRIPTION NUMBER NUMBER DESCRIPTION IC903 79040102 NJM2370U05 DY07 79060022 Diode,Chip 1SS368 IC904 79040087 TC7W241FU DY08 79060022 Diode,Chip 1SS368 - TRANSISTORS - - CAPACITORS - Q501 79050036 Transistor,Chip 2SA1832-GR CV01 79020062 Cap,Electrolytic 47MF M 16V Q502 79050042 Transistor,Chip...
Page 30
LOCATION PART LOCATION PART NUMBER NUMBER DESCRIPTION NUMBER NUMBER DESCRIPTION JY02 79089007 Plate,Jack Digital Audio SY01 79080018 Relay EG2-9...
SPECIFICATIONS DVD Video Player/Outputs/Supplied Accessories [DVD Video Player] Power supply 120V AC, 60 Hz Power consumption Mass 3.5 kg External dimensions 430 x 102 x 305 mm (W/H/D) Signal system Standard NTSC Laser Semiconductor laser, wavelength 650 nm Frequency range DVD linear sound : 48 kHz sampling 4 Hz to 22 kHz 96 kHz sampling 4 Hz to 44 kHz Signal-to-noise ratio...